Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL SYSTEM
RM25T0E _51 Engine / Hybrid System _029892 1GR-FE FUEL _0135855 FUEL SYSTEM L

1GR-FE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·

Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.

·

Do not smoke or be near an open flame when working on the fuel system.

·

Keep gasoline away from rubber and leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.

·

After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.



a.
A220786C01
0.052,0.063 0.365,0.313 0.313,0.25 10 true *A 0.083,2.292 0.417,2.531 0.333,0.24 10 true *B
*A for Model Code #J71 Series
*B for Model Code #J76 Series


for Model Code #J71, #J76 Series:

Disconnect the fuel pump connector.


b.

for Model Code #J78, #J79 Series:

i.
A220707

for Single Tank Type:

Disconnect the fuel pump connector.


ii.
A220787C01
0.063,0.063 0.417,0.323 0.354,0.26 10 true *A 0.083,2.344 0.438,2.625 0.354,0.281 10 true *B
*A for Fuel Main Tank
*B for Fuel Sub Tank


for Double Tank Type:

Disconnect the 2 fuel pump connectors.



c.
A293629

for 130 L Tank:

Disconnect the fuel pump connector.


d.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

HINT:

If a DTC is output, clear the DTC.

Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



e.

Crank the engine and check that the engine does not start.


f.

Loosen the fuel tank cap assembly, and then discharge the pressure in the fuel tank completely.


g.

Disconnect the cable from the negative (-) battery terminal.


h.

for Model Code #J71, #J76 Series:

Connect the fuel pump connector.


i.

for Model Code #J78, #J79 Series:

i.

for Single Tank Type:

Connect the fuel pump connector.


ii.

for Double Tank Type:

Connect the 2 fuel pump connectors.



j.

for 130 L Tank:

Connect the fuel pump connector.



FUEL SYSTEM


a.

When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

i.

Discharge the fuel system pressure (see above procedure).


ii.

Put a container under the connecting part of the pressure line.


iii.

Slowly loosen the connection.


iv.

Disconnect the connection.


v.

Plug the connection with a rubber plug.



b.
A133695C02
0.573,2.729 0.74,2.729 0.74,2.729 0.823,2.229 false 1.51,2.781 1.344,2.781 1.344,2.781 1.26,2.281 false 0.365,2.646 0.667,2.875 0.302,0.229 10 false *1 1.594,2.698 1.906,2.917 0.313,0.219 10 false *2 2.344,0.219 2.698,0.469 0.354,0.25 10 false *a 2.385,1.125 2.646,1.365 0.26,0.24 10 false *b 2.396,2.24 2.635,2.438 0.24,0.198 10 false *b
*1 O-Ring
*2 Fuel Delivery Pipe Sub-assembly
*a CORRECT
*b INCORRECT


Observe these precautions when removing and installing the fuel injector assemblies:

NOTICE:
·

Never reuse the O-ring.

·

When installing a new O-ring to the injector, do not damage it.

·

Coat a new O-ring with spindle oil or gasoline before installing it. Do not use engine oil, gear oil or brake oil.




c.
A133696C02
0.708,2.49 1.208,2.49 true 1,0.667 1.167,0.667 1.167,0.667 1.594,1.125 true 2.281,0.344 2.115,0.344 2.115,0.344 1.865,0.677 true 0.948,1.729 1.448,1.729 true 2.125,1.823 2.625,1.823 true 0.708,0.573 1.01,0.844 0.302,0.271 10 false *1 2.375,0.26 2.688,0.417 0.313,0.156 10 false *2 0.74,1.646 1.052,1.917 0.313,0.271 10 false *3 2.688,1.74 3,1.896 0.313,0.156 10 false *4 0.49,2.396 0.74,2.604 0.25,0.208 10 false *5
*1 O-Ring
*2 Fuel Delivery Pipe Sub-assembly
*3 Fuel Injector Assembly
*4 Intake Manifold
*5 Fuel Vibration Insulator


Install the fuel injector assembly to the fuel delivery pipe sub-assembly and intake manifold as shown in the illustration.

NOTICE:

Before installing the fuel injector assembly, apply spindle oil or gasoline to the place where the fuel delivery pipe sub-assembly contacts the O-ring of the fuel injector assembly.



d.

Observe these precautions when disconnecting the fuel tube connector.

i.
A181442C01
0.927,3.24 1.427,3.24 true 0.896,0.76 1.063,0.76 1.063,0.76 1.313,1.26 true 0.104,0.052 0.469,0.333 0.365,0.281 10 false *a 0.688,0.677 1.031,0.969 0.344,0.292 10 false *1 0.729,3.156 1.073,3.448 0.344,0.292 10 false *2
*1 No. 1 Fuel Pipe Clamp
*2 No. 2 Fuel Pipe Clamp
*a for Fuel Pipe Clamp Type


for Fuel Pipe Clamp Type:

Remove the fuel pipe clamp from the fuel tube connector.


ii.
A157617C06
0.063,0.073 0.448,0.396 0.385,0.323 10 false *a
*a for Fuel Hose Connector Cover Type
V100135

Pull


for Fuel Hose Connector Cover Type:

Detach the lock claw by lifting up the cover as shown in the illustration.


iii.

Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.


iv.
A147380C01
0,0 0,0 false
V100135

Pinch
V100136

Pull


Pinch the connector and disconnect the connector and pipe.

If the connector and the pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.

NOTICE:
·
A220697C01
0.5,1.042 0.833,1.042 true 0.656,1.729 0.823,1.729 0.823,1.729 0.99,1.313 true 0.99,0.875 0.802,0.375 0.802,0.375 0.635,0.375 true 1.458,1.531 1.313,1.531 1.313,1.531 1.313,1.167 true 1.458,1.177 1.458,1.76 true 2.135,0.885 2.302,0.469 2.302,0.469 2.469,0.469 true 1.375,1.813 1.677,2.031 0.302,0.219 10 false *1 0.458,1.635 0.75,1.833 0.292,0.198 10 false *2 0.302,0.948 0.563,1.167 0.26,0.219 10 false *3 0.438,0.292 0.688,0.542 0.25,0.25 10 false *4 2.521,0.365 2.823,0.604 0.302,0.24 10 false *a
*1 O-Ring
*2 Connector
*3 Pipe
*4 Retainer
*a Nylon Tube


Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.

·

Do not use any tools to separate the pipe and connector.

·

Do not forcefully bend or twist the nylon tube.

·

Check for foreign matter on the pipe seal surface. Clean if necessary.

·

Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.

·

If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.




v.

Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.


vi.

To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.



e.
A130944C01
0,0 0,0 false
V100135

Push


Observe these precautions when connecting the fuel tube connector.

i.

Check that there is no damage or contamination in the connected part of the pipe.


ii.

Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.

NOTICE:
·
A220697C02
1.458,1.771 1.458,1.188 true 1.458,1.51 1.302,1.51 1.302,1.51 1.302,1.177 true 0.583,1.729 0.75,1.729 0.75,1.729 1,1.313 true 0.813,1.052 0.479,1.052 true 0.646,0.458 0.813,0.458 0.813,0.458 0.99,0.875 true 2.604,0.469 2.406,0.469 2.406,0.469 2.198,0.885 true 1.365,1.823 1.656,2.042 0.292,0.219 10 false *1 0.385,1.635 0.76,1.896 0.375,0.26 10 false *2 0.292,0.979 0.542,1.167 0.25,0.188 10 false *3 0.458,0.375 0.708,0.583 0.25,0.208 10 false *4 2.677,0.385 2.99,0.604 0.313,0.219 10 false *a
*1 O-Ring
*2 Connector
*3 Pipe
*4 Retainer
*a Nylon Tube


Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.

·

After connecting the connectors and pipes, check if they are securely connected by trying to pull them apart.




iii.
A130945C01
0,0 0,0 false
V100135

Pull


After having finished the connection, try to pull apart the pipe and connector to confirm that they are securely connected.


iv.
A157616C01
0.073,0.063 0.458,0.365 0.385,0.302 10 false *a
*a for Fuel Hose Connector Cover Type
V100135

Push


for Fuel Hose Connector Cover Type:

Attach the lock claw to the connector by pushing down on the cover as shown in the illustration.


v.
A181442C02
1.427,2.521 1.594,2.521 1.594,2.521 1.844,2.854 true 0.833,0.958 1,0.958 1,0.958 1.25,1.292 true 0.125,0.125 0.469,0.427 0.344,0.302 10 false *a 0.625,0.865 0.875,1.115 0.25,0.25 10 false *1 1.208,2.438 1.51,2.729 0.302,0.292 10 false *2
*1 No. 1 Fuel Pipe Clamp
*2 No. 2 Fuel Pipe Clamp
*a for Fuel Pipe Clamp Type


for Fuel Pipe Clamp Type:

Install the fuel pipe clamp to the fuel tube connector.


vi.

Check that there is no fuel leakage.




CHECK FOR FUEL LEAK


a.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION