Home › Engine / Hybrid System › 1GR-FE (FUEL) › FUEL INJECTOR
RM25T0E _51 Engine / Hybrid System _029892 1GR-FE FUEL _0135856 FUEL INJECTOR G

1GR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


Hide 23250 2.INSPECT INJECTION VOLUME AND LEAKAGE

a.

Check the injector injection.

CAUTION:
·

This test involves high-pressure fuel and electricity.

·

Take every precaution regarding safe handling of both the fuel and the electrical parts.

·

Perform this test in a safe area, and avoid any sparks or flame.

·

Do not smoke.



i.

Discharge the fuel system pressure.

Click hereEngine / Hybrid System>1GR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


ii.
A329133C03
0.292,1.583 0.396,1.583 0.396,1.583 0.615,1.771 true 0.646,1.385 0.75,1.385 0.75,1.385 0.969,1.573 true 1.177,1.208 1.281,1.208 1.281,1.208 1.5,1.396 true 1.375,1.01 1.479,1.01 1.479,1.01 1.698,1.198 true 1.677,0.604 1.781,0.604 1.781,0.604 2,0.792 true 1.823,0.271 1.927,0.271 1.927,0.271 2.198,0.729 true 2.344,0.604 2.406,0.229 2.406,0.229 2.542,0.229 true 2.635,1.646 2.781,1.646 true 1.771,1.844 1.875,1.844 1.875,1.844 2.063,1.667 true 3.021,0.458 3.167,0.458 true 2.688,2.021 2.781,2.021 2.781,2.021 2.927,1.885 true 1.99,2.135 2.135,2.135 true 1.979,2.74 2.125,2.74 true 2.542,2.646 2.688,2.646 true 3.021,2.417 3.167,2.417 true 0.073,1.49 0.313,1.688 0.24,0.198 10 false *1 1.76,2.656 1.958,2.844 0.198,0.188 10 false *2 3.219,2.344 3.417,2.51 0.198,0.167 10 false *3 0.427,1.292 0.656,1.49 0.229,0.198 10 false *a 0.969,1.115 1.198,1.313 0.229,0.198 10 false *b 2.479,1.927 2.688,2.115 0.208,0.188 10 false *c 1.167,0.917 1.396,1.104 0.229,0.188 10 false *d 1.771,2.031 1.979,2.208 0.208,0.177 10 false *e 2.76,2.573 2.958,2.75 0.198,0.177 10 false *f 1.615,0.146 1.854,0.365 0.24,0.219 10 false *g 1.458,0.51 1.688,0.708 0.229,0.198 10 false *b 2.604,0.146 2.833,0.344 0.229,0.198 10 false *b 3.208,0.365 3.396,0.531 0.188,0.167 10 false *d 1.563,1.76 1.781,1.948 0.219,0.188 10 false *b 2.438,1.542 2.646,1.729 0.208,0.188 10 false *b
*1 Fuel Pressure Regulator Assembly
*2 Fuel Injector Assembly
*3 Fuel Pipe
*a SST (Union)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d SST (Hose)
*e SST (Adapter)
*f SST (Clamp)
*g SST (T-Joint)


Assemble SST as shown in the illustration.

SST
09268-31014  (09268-41091, 09268-41120, 09268-41141, 09268-41410, 09268-41500, 09268-41700, 95336-08070)


iii.

Disconnect the fuel inlet hose (fuel tube connector) from the fuel pipe.


iv.

Remove the 2 bolt and disconnect the fuel pressure regulator assembly from the fuel delivery pipe sub-assembly.

NOTICE:

Do not disconnect the No. 2 fuel pipe sub-assembly from the fuel pressure regulator assembly.



v.
A273743C02
2.021,1.875 2.354,1.875 true 2.5,0.875 2.802,0.875 true 1.833,1.781 2.104,2.01 0.271,0.229 10 false *1 2.885,0.792 3.146,1.01 0.26,0.219 10 false *a
*1 Fuel Pipe
*a SST (Fuel Tube Connector)


Connect SST to the fuel pipe.

SST
09268-31014  (09268-41500)

CAUTION:

Always read the precautions before connecting the fuel tube connector.



vi.
A308642C01
3.031,0.51 3.031,0.177 true 2.76,1.083 2.594,1.083 2.594,1.083 2.427,0.75 true 0.906,0.552 1.24,0.552 true 0.5,1.135 0.583,1.135 0.583,1.135 0.76,1.396 true 0.708,0.469 0.99,0.708 0.281,0.24 10 false *1 0.271,1.063 0.552,1.323 0.281,0.26 10 false *2 2.833,0.99 3.125,1.229 0.292,0.24 10 false *a 2.979,0.552 3.25,0.833 0.271,0.281 10 false *b
*1 Fuel Pressure Regulator Assembly
*2 No. 2 Fuel Pipe Sub-assembly
*a SST (Union)
*b SST (Hose)


Connect SST (hose) to the fuel inlet of the fuel pressure regulator assembly with another SST (union) and the 2 bolts.

SST
09268-31014  (09268-41091, 95336-08070)

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)


vii.
A329134C02
0.469,0.677 0.729,0.677 true 0.417,1.01 0.677,1.01 true 0.417,2.135 0.677,2.135 true 2.146,1.042 2.406,0.74 2.406,0.74 2.531,0.74 true 2.625,1.958 2.885,1.958 true 2.615,0.667 2.875,0.854 0.26,0.188 10 false *1 0.25,0.583 0.448,0.781 0.198,0.198 10 false *a 0.188,0.917 0.396,1.104 0.208,0.188 10 false *b 0.198,2.052 0.417,2.25 0.219,0.198 10 false *c 2.958,1.875 3.177,2.063 0.219,0.188 10 false *d
*1 O-Ring
*a SST (Hose)
*b SST (Hose Band)
*c SST (Adapter)
*d SST (Clamp)


Install a new O-ring to the fuel injector assembly.


viii.

Connect SST (adapter and hose) to the fuel injector assembly, and hold the fuel injector assembly and adapter with SST (clamp).

SST
09268-31014  (09268-41141, 09268-41410, 09268-41700, 95336-08070)


ix.
A329135C02
1.552,1.604 1.729,1.938 1.729,1.938 1.875,1.938 true 2.479,0.76 2.646,0.979 2.646,0.979 2.792,0.979 true 1.948,1.854 2.167,2.042 0.219,0.188 10 false *a 2.875,0.885 3.094,1.063 0.219,0.177 10 false *b
*a SST (Tie Band)
*b Lock


Pass SST (tie band) through the loop on the handle of SST (clamp) to secure SST (clamp) to SST (adapter).

SST
09268-31014  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.


·

Before using SST (tie band), make sure that there is no deterioration, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



x.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


xi.

Put the fuel injector assembly into a graduated cylinder.

CAUTION:

Install a suitable vinyl tube to the fuel injector assembly to contain any gasoline spray.



xii.

Connect the GTS to the DLC3.


xiii.

Turn the ignition switch to ON.

NOTICE:

Do not start the engine.



xiv.

Turn the GTS on.


xv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the Fuel Pump Speed Control.

Powertrain > Engine and ECT > Active Test
Tester Display
Activate the Fuel Pump Speed Control
50004 61 4

xvi.
A329136C02
1.552,0.281 1.698,0.875 1.698,0.875 1.823,0.875 true 1.896,0.792 2.125,0.99 0.229,0.198 10 false *a
*a SST (Wire)


Connect SST (wire) to the fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.

SST
09842-30080  

Standard injection volume:

76 to 91 cc (4.6 to 5.6 cu. in.) per 15 seconds


Difference between each injector:

15 cc (0.9 cu. in.) or less


NOTICE:

Always turn the voltage on and off on the battery side, not the fuel pump side.


If the result is not as specified, replace the fuel injector assembly.



b.

Check for fuel leakage.

i.

In the condition above, disconnect the tester probes of SST (wire) from the battery and check for fuel leakage from each fuel injector assembly.

Standard:

1 drop or less per 17 minutes


If the leakage is not as specified, replace the fuel injector assembly.