Home › Engine / Hybrid System › 1HZ (FUEL) › FUEL INJECTION PUMP
RM25T0E _51 Engine / Hybrid System _029893 1HZ FUEL _0136493 FUEL INJECTION PUMP N

1HZ FUEL  FUEL INJECTION PUMP  ADJUSTMENT  


PROCEDURE

Hide 1.PRE-TEST CHECK AND PREPARATION

a.
A334002

The specifications for the test nozzle and nozzle holders are as follows.

Test nozzle:

DN12SD12 (DENSO)


Test nozzle opening pressure:

14220 to 15200 kPa (145.0 to 155.0 kgf/cm2, 2062 to 2204 psi)



b.
A334003

Check the accuracy of the tachometer.

Allowable error:

0 to 80 rpm



c.
A334004

Install the angle gauge stand.


d.

Mount the injection pump body on the pump tester.

HINT:

Place a mark on the key groove portion of the coupling.



e.
A334005

Install an injection pipe with the following specifications.

Outer diameter:

6.0 mm (0.236 in.)

Inner diameter:

2.0 mm (0.0787 in.)

Length:

840 mm (2.76 ft.)

Minimum bending radius:

25 mm (0.984 in.) or more



f.
A334006

Remove the fuel inlet hollow screw.


g.

Connect the fuel inlet pipe with an adapter.


h.
A334007C01
2.458,0.646 2.563,0.198 2.563,0.198 2.688,0.198 true 2.729,0.094 2.938,0.281 0.208,0.188 10 false *a
*a Overflow Screw


Install the overflow hose with the overflow screw.

HINT:

Always use the overflow screw installed on the pump to be adjusted.



i.
A334008C01
2.313,1.615 2.51,1.875 2.51,1.875 2.667,1.875 true 2.104,1.354 2.271,1.188 2.271,1.188 2.438,1.188 false 2.698,1.771 3.01,1.927 0.313,0.156 10 false *a 2.479,1.083 2.792,1.24 0.313,0.156 10 false *b
*a Air Bleed Screw
*b Timer Measuring Device


Using a 5 mm hexagon wrench, remove the 2 bolts and RH timer cover.


j.

Install the inner pressure gauge with the timer measuring device.

Part No. 95095-10220 and 95095-10231

(DENSO)

HINT:

Bleed the air by the air bleed screw.



k.

w/ BACS:

Connect SST (turbocharger pressure gauge) to the boost compensator.

SST
09992-00242  

A334086C01
4.938,0.677 5.063,0.396 5.063,0.396 5.292,0.396 false 5.854,0.677 5.948,0.396 5.948,0.396 6.177,0.396 false 6.01,1.375 6.01,1.146 6.01,1.146 6.438,1.146 false 5.438,5.073 5.438,4.844 5.438,4.844 5.865,4.844 false 4.375,4.438 4.479,4.208 4.479,4.208 4.708,4.208 false 5.073,4.438 5.167,4.188 5.167,4.188 5.396,4.188 false 3.115,0.604 3.313,0.604 3.313,0.604 3.552,0.885 false 6.344,2.375 6.635,2.375 false 6.323,1.844 6.615,1.844 false 5.427,2.344 5.719,2.344 false 0.375,0.885 0.573,0.885 0.573,0.885 0.813,1.167 false 0.365,4.583 0.563,4.583 0.563,4.583 0.802,4.865 false 4.865,6.063 5.156,6.063 false 5.76,6.083 6.052,6.083 false 5.75,5.552 6.042,5.552 false 0.135,0.115 0.448,0.271 0.313,0.156 10 false *A 6.5,1.042 6.698,1.219 0.198,0.177 10 false *a 6.219,0.302 6.427,0.458 0.208,0.156 10 false *b 6.646,1.729 6.833,1.917 0.188,0.188 10 false *c 6.656,2.26 6.854,2.438 0.198,0.177 10 false *d 5.948,3.135 6.146,3.313 0.198,0.177 10 false *e 5.333,0.302 5.521,0.458 0.188,0.156 10 false *f 5.25,2.219 5.458,2.417 0.208,0.198 10 false *g 0.198,0.781 0.406,0.969 0.208,0.188 10 false *h 2.958,0.49 3.125,0.677 0.167,0.188 10 false *i 4.75,4.115 4.938,4.271 0.188,0.156 10 false *f 5.438,4.094 5.646,4.25 0.208,0.156 10 false *b 5.927,4.74 6.125,4.917 0.198,0.177 10 false *a 6.094,5.448 6.281,5.635 0.188,0.188 10 false *c 6.083,5.979 6.281,6.156 0.198,0.177 10 false *d 4.688,5.938 4.896,6.135 0.208,0.198 10 false *g 5.344,6.854 5.542,7.031 0.198,0.177 10 false *e 0.156,4.479 0.365,4.667 0.208,0.188 10 false *h
*A w/ BACS - -
*a Adjusting Valve *b Fuel Feed Pump
*c Fuel Filter *d Fuel Pressure Gauge
*e Fuel Tank *f Inner Pressure Gauge
*g Measuring Cylinder *h Nozzle
*i SST (Turbocharger Pressure Gauge) - -



l.
A334011C01
2.771,0.958 3,1.156 0.229,0.198 10 false *a
*a Fuel Cut Solenoid


12 V type:

Apply approx. 6 V of DC power to the fuel cut solenoid.


m.

24 V type:

Apply approx. 14 V of DC power to the fuel cut solenoid.

NOTICE:
·

When applying voltage to the solenoid, position the battery as far away from the solenoid as possible so that a spark does not occur.

·

When connecting the battery cable, connect the solenoid side first.




n.
A334012C01
0.76,0.198 0.969,0.396 0.208,0.198 10 false *a 2.5,0.24 2.729,0.417 0.229,0.177 10 false *b
*a Fuel Pressure
*b Fuel Temperature


The pressure for feeding fuel to the injection pump should be 20 kPa (0.2 kgf/cm2, 3 psi). The fuel temperature for pump testing should be 40 to 45°C (104 to 113°F).


o.
A334013

Install an angle gauge to the stand and set it to the adjusting lever.


p.

Secure the adjusting lever fully on the maximum speed side.


q.
A334014N01
1.229,0.458 1.375,0.458 1.375,0.458 1.5,0.948 true 0.906,0.365 1.25,0.563 0.344,0.198 10 false SST

Check the installation direction of the camplate as follows:

·

Disconnect the injection pipe from the position marked "C" on the distributive head.

·

Using SST, remove the delivery valve holder.


SST
09260-54012  (09269-54020)

·
A334015

Check that fuel is flowing out when the mark is in the position shown in the illustration.

If not, it is improperly assembled.

·

Disassemble and change the camplate position 180° in the opposite direction.


HINT:

At this time, disconnect the fuel cut solenoid wire harness.


·
A334016N01
1.198,0.583 1.323,0.583 1.323,0.583 1.458,0.958 true 0.865,0.49 1.198,0.688 0.333,0.198 10 false SST

Using SST, install the delivery valve holder.

·

Connect the injection pipe.


SST
09260-54012  (09269-54020)


r.
A334017

Bleed the air from the injection pipes.


s.
A334018

Race the injection pump for 5 minutes at 2000 rpm.

NOTICE:

Check that there is no fuel leakage or abnormal noise.


HINT:
A334019C01
2.354,0.406 2.552,0.604 0.198,0.198 10 false *a
*a 30 Seconds


·

Measure the volume of each injection cylinder with a measuring cylinder.

·

Before measuring the injection volume first hold the cylinder tilted for at least 30 seconds to discard all the fuel.




Hide 2.PRE-SET FULL LOAD INJECTION VOLUME

a.

Set the adjusting lever to the maximum position.


b.

w/ HAC:

Apply 101.1 to 101.5 kPa (758 to 761 mmHg, 29.85 to 29.97 in.Hg) absolute pressure.


c.

Measure the injection volume.

Pump rpm No. of measuring strokes Injection volume
1200 200 11.88 to 12.28 cc (0.72 to 0.75 cu.in.)


d.
A334020C01
1.458,0.438 1.729,0.656 0.271,0.219 10 true *a
*a 90° or more


Remove the collar seal as follows:

·

Hold the full load set screw, and release the collar seal from the spot weld by turning the lock nut counterclockwise by 90° or more.

·

Using a screwdriver, remove the collar seal.



e.

w/ Wire Seal Type:

Cut off the wire seal.


f.
A334022C01
1.031,0.667 1.219,0.667 1.219,0.667 1.521,0.99 true 0.833,0.583 1.042,0.771 0.208,0.188 10 false *1
*1 Full Load Set Screw


Adjust by turning the full load set screw.

HINT:

The injection volume will increase about 3 cc (0.18 cu. in.) with each 1/2 turn of the screw.



Hide 3. PRE-SETTING OF LOAD SENSING TIMER (w/o HIGH ALTITUDE)

a.
A334023C01
2.385,0.354 2.604,0.552 0.219,0.198 10 false *a
*a Protrusion


Using a 5 mm hexagon wrench, adjust the protrusion of the governor shaft.

Protrusion:

0.5 to 2.0 mm (0.0197 to 0.0787 in.)



Hide 4. PRE-SET MAXIMUM SPEED

a.

Set the adjusting lever to the maximum position.


b.

w/ HAC:

Apply 101.1 to 101.5 kPa (758 to 761 mmHg, 29.85 to 29.97 in.Hg) absolute pressure.


c.

Measure the injection volume.

Pump rpm No. of measuring strokes Injection volume
2300 200 4.44 to 6.44 cc (0.27 to 0.39 cu.in.)


d.

Cut off the seal wire.


e.
A334024C01
0.99,0.177 1.313,0.177 1.313,0.177 1.875,0.74 true 0.781,0.094 0.979,0.281 0.198,0.188 10 false *1
*1 Maximum Speed Adjusting Screw


Adjust the injection volume with the maximum speed adjusting screw.


Hide 5.ADJUST PUMP INNER PRESSURE

a.
A334018

Measure the pump inner pressure at the following listed rpm.

Pump rpm Inner pressure
500 343 to 402 kPa (3.5 to 4.1 kgf/cm2, 50 to 58 psi)
1900 760 to 820 kPa (7.7 to 8.4 kgf/cm2, 110 to 119 psi)


b.
A334025

If the pressure is low, adjust by lightly tapping the regulator valve piston while watching the pressure gauge.

HINT:

If the pressure is too high or if the regulator valve was tapped in too far, the regulator must be replaced.



Hide 6.CHECK OVERFLOW VOLUME

a.
A334026

Measure the overflow volume at the following listed rpm.

Pump rpm Overflow volume
2000 366 to 800 cc/min. (22.3 to 48.8 cc in./min.)

HINT:

Always use the overflow screw installed on the pump to be adjusted.



Hide 7.RELEASE COLD STARTING SYSTEM FOR FOLLOWING INSPECTIONS (w/ ACSD)

a.
A334027C01
1.583,1.219 2,0.75 2,0.75 2.229,0.75 false 2.271,0.656 2.479,0.844 0.208,0.188 10 false *a
*a Metal Plate


Using a screwdriver, turn the cold starting lever counterclockwise approx. 20°.


b.

Put a metal plate (thickness of 3.5 to 7.5 mm (0.138 to 0.295 in.)) between the cold starting lever and thermo wax plunger.

HINT:

Keep the cold starting system released until all measurements and adjustments are finished.



Hide 8.ADJUST TIMER

a.
A334028

Set the timer measuring device at zero.


b.

Measure the timer piston stroke at the following listed rpms.

Timer Piston Stroke (w/ BACS):
Pump rpm Timer piston stroke
800 2.6 to 3.2 mm (0.102 to 0.126 in.)
1200 4.5 to 5.1 mm (0.177 to 0.201 in.)
1520 5.98 to 6.56 mm (0.235 to 0.258 in.)
1900 7.17 to 7.65 mm (0.282 to 0.301 in.)

Timer Piston Stroke (w/o BACS):
Pump rpm Timer piston stroke
800 0.61 to 1.61 mm (0.0240 to 0.0634 in.)
1200 2.47 to 3.47 mm (0.0972 to 0.137 in.)
1520 3.95 to 4.95 mm (0.156 to 0.195 in.)
1900 5.72 to 6.72 mm (0.225 to 0.265 in.)
2500 7.17 to 7.65 mm (0.282 to 0.301 in.)
(LST non-operational)

HINT:

Check that the hysteresis is within 0.3 mm (0.0118 in.).



c.
A334029

Using a 5 mm hexagon wrench, adjust by turning the timer adjusting screw.

HINT:

The stroke will decrease by turning clockwise and increase by turning counterclockwise.



Hide 9.CHECK AIRTIGHTNESS OF BOOST COMPENSATOR

a.
A334030

Apply 98 kPa (1.0 kgf/cm2, 14 psi) of pressure to the boost compensator.


b.

Measure the time it takes for the pressure to drop to 95 kPa (1.0 kgf/cm2, 14 psi).

Pressure drop:

10 seconds or more



Hide 10.ADJUST FULL LOAD INJECTION VOLUME

a.
A334031E01
1.854,0.01 2.083,0.198 0.229,0.188 10 true 0° 1.969,0.323 2.125,0.521 0.156,0.198 10 false A 1.76,0.323 1.917,0.521 0.156,0.198 10 false B

The adjusting lever angle for the adjustment below should be as shown in the illustration.

Adjusting Lever Angle:
A (Maximum speed side) B (Idle speed side)
Plus 21 to 31° Minus 12 to 22°



b.

w/ HAC:

Apply 101.1 to 101.5 kPa (758 to 761 mmHg, 29.85 to 29.97 in.Hg) absolute pressure.


c.

Measure the full load injection volume.

Adjusting lever angle Pump rpm No. of measuring strokes Injection volume
Plus 21 to 31° 1200 200 11.88 to 12.28 cc (0.72 to 0.75 cu.in.)


d.
A334032C01
0.896,0.552 1.083,0.552 1.083,0.552 1.5,0.979 true 0.698,0.448 0.906,0.635 0.208,0.188 10 false *1
*1 Full Load Set Screw


Adjust by turning the full load set screw.

HINT:

The injection volume will increase about 3 cc (0.18 cu. in.) with each 1/2 turn of the screw.



Hide 11.ADJUST MAXIMUM SPEED

a.

w/ HAC:

Apply 101.1 to 101.5 kPa (758 to 761 mmHg, 29.85 to 29.97 in.Hg) absolute pressure.


b.

Measure the injection volume at each pump rpm.

Adjusting lever angle Pump rpm No. of measuring strokes Injection volume Remarks
Plus 21 to 31° 2300 200 4.44 to 6.44 cc (0.27 to 0.39 cu.in.) Adjust


c.
A334024C01
0.99,0.177 1.313,0.177 1.313,0.177 1.875,0.74 true 0.781,0.094 0.979,0.281 0.198,0.188 10 false *1
*1 Maximum Speed Adjusting Screw


Adjust by turning the maximum speed adjusting screw.


Hide 12.CHECK INJECTION VOLUME

a.

w/ HAC:

Apply 101.1 to 101.5 kPa (758 to 761 mmHg, 29.85 to 29.97 in.Hg) absolute pressure.


b.

Measure the injection volume at each pump rpm.

Adjusting lever angle Pump rpm No. of measuring strokes Injection volume Remarks
Plus 21 to 31° 1200 200 12.08 cc (0.74 cu.in.) Basic full-load injection volume
100 1.2 cc (0.07 cu.in.) Volume during starting
500 10.6 cc (0.65 cu.in.) -
1900 11.22 cc (0.68 cu.in.) -

If the injection volume at 100 rpm is not as specified, replace the governor sleeve plug as follows:

·
A334087N01
1.781,0.813 2.208,0.573 2.208,0.573 2.396,0.573 false 2.448,0.49 2.781,0.677 0.333,0.188 10 false SST

Using SST and a press, press out the sleeve plug assembly from the governor sleeve.


SST
09236-00101  (09237-00070)

·
A334088C01
1.844,0.26 2.375,0.26 false 1.833,1.708 2.333,1.708 false 1.813,1.99 2.333,1.99 false 2.219,1.385 2.219,0.74 2.219,0.74 1.885,0.74 false 1.885,1.073 2.385,1.073 false 1.885,1.385 2.219,1.385 false 2.385,1.625 2.698,1.781 0.313,0.156 10 false *1 2.427,0.979 2.74,1.135 0.313,0.156 10 false *2 2.385,1.896 2.698,2.052 0.313,0.156 10 false *3 2.417,0.177 2.729,0.333 0.313,0.156 10 false *4
*1 Stop Ring
*2 Bearing and Bearing Retainer
*3 E-Ring
*4 Sleeve Plug


Remove the E-ring and following parts from the sleeve plug:

(1) Stop ring

(2) Bearing and 2 bearing retainers

·
A334089C01
1.823,0.26 2.031,0.458 0.208,0.198 10 false *a
*a Head Thickness


Measure the head thickness of the sleeve plug, and select a new sleeve plug.

w/o BACS:
Sleeve plug head thickness
3.0 mm (0.118 in.) 3.5 mm (0.138 in.) 4.0 mm (0.158 in.)
3.1 mm (0.122 in.) 3.6 mm (0.142 in.) 4.1 mm (0.161 in.)
3.2 mm (0.126 in.) 3.7 mm (0.146 in.) 4.2 mm (0.165 in.)
3.3 mm (0.130 in.) 3.8 mm (0.150 in.) -
3.4 mm (0.134 in.) 3.9 mm (0.154 in.) -

w/ BACS:
Sleeve plug head thickness
3.0 mm (0.118 in.) 4.3 mm (0.169 in.) 5.6 mm (0.220 in.)
3.1 mm (0.122 in.) 4.4 mm (0.173 in.) 5.7 mm (0.224 in.)
3.2 mm (0.126 in.) 4.5 mm (0.177 in.) 5.8 mm (0.228 in.)
3.3 mm (0.130 in.) 4.6 mm (0.181 in.) 5.9 mm (0.232 in.)
3.4 mm (0.134 in.) 4.7 mm (0.185 in.) 6.0 mm (0.236 in.)
3.5 mm (0.138 in.) 4.8 mm (0.189 in.) 6.1 mm (0.240 in.)
3.6 mm (0.142 in.) 4.9 mm (0.193 in.) 6.2 mm (0.244 in.)
3.7 mm (0.146 in.) 5.0 mm (0.197 in.) 6.3 mm (0.248 in.)
3.8 mm (0.150 in.) 5.1 mm (0.201 in.) 6.4 mm (0.252 in.)
3.9 mm (0.154 in.) 5.2 mm (0.205 in.) 6.5 mm (0.256 in.)
4.0 mm (0.157 in.) 5.3 mm (0.209 in.) 6.6 mm (0.260 in.)
4.1 mm (0.161 in.) 5.4 mm (0.213 in.) -
4.2 mm (0.165 in.) 5.5 mm (0.216 in.) -


HINT:

Lengthening the plug 0.1 mm (0.004 in.) will decrease the injection volume by 0.6 cc (0.04 cu. in.).


·
A334088C01
1.844,0.26 2.375,0.26 false 1.833,1.708 2.333,1.708 false 1.813,1.99 2.333,1.99 false 2.219,1.385 2.219,0.74 2.219,0.74 1.885,0.74 false 1.885,1.073 2.385,1.073 false 1.885,1.385 2.219,1.385 false 2.385,1.625 2.698,1.781 0.313,0.156 10 false *1 2.427,0.979 2.74,1.135 0.313,0.156 10 false *2 2.385,1.896 2.698,2.052 0.313,0.156 10 false *3 2.417,0.177 2.729,0.333 0.313,0.156 10 false *4
*1 Stop Ring
*2 Bearing and Bearing Retainer
*3 E-Ring
*4 Sleeve Plug


Install the following parts to a new sleeve plug with a new E-ring:

(1) Bearing and 2 retainers

(2) Stop ring

·
A334090

Using a press, press in the sleeve plug assembly to the governor sleeve.



Hide 13.ADJUST FULL LOAD MINIMUM INJECTION VOLUME (w/ BACS)

a.

Measure the injection volume.

Pump rpm No. of measuring strokes Injection volume
1200 200 9.82 to 10.42 cc (0.60 to 0.64 cu.in.)


b.
A334033C01
2.01,1.198 2.167,1.125 2.167,1.125 2.729,1.125 true 2.792,1.031 3.104,1.188 0.313,0.156 10 false *a
*a Timer Slide Pin


Using a hexagon wrench, adjust the timer slide pin.


Hide 14.ADJUST BOOST COMPENSATOR CHARACTERISTIC (w/ BACS)

a.

Apply pressure to the boost compensator.


b.

Measure the injection volume bushing.

Pump rpm Boost pressure No. of measuring strokes Injection volume
1200 35 kPa (0.4 kgf/cm2, 5 psi) 200 10.98 to 11.78 cc (0.67 to 0.72 cu.in.)


c.
A334034C01
2.646,0.688 2.865,1.406 2.865,1.406 3.021,1.406 true 3.063,1.313 3.281,1.49 0.219,0.177 10 false *1
*1 Guide Bushing


Using a screwdriver, adjust the bushing.

HINT:

When the guide bushing is turned clockwise, as seen from above, the injection volume will increase.



Hide 15.INSPECT BOOST COMPENSATOR CHARACTERISTIC TENDENCY (w/ BACS)

a.
A334035C01
2.479,2.115 2.667,2.281 0.188,0.167 10 false *a 0.865,2.708 1.073,2.875 0.208,0.167 10 false *b 0.823,0.271 1.031,0.448 0.208,0.177 10 false *c 1.271,2.49 1.5,2.667 0.229,0.177 10 false *d 1.698,2.219 1.917,2.396 0.219,0.177 10 false *e 0.406,0.854 0.594,1.031 0.188,0.177 10 false *f 1.927,1.823 2.167,2.021 0.24,0.198 10 false *g 1.958,3.302 2.167,3.479 0.208,0.177 10 false *h 2.198,1.135 2.406,1.302 0.208,0.167 10 false *b 2.208,0.594 2.396,0.76 0.188,0.167 10 false *a 0.406,2.51 0.594,2.688 0.188,0.177 10 false *f
*a Adjust Full-load Injection Volume
*b Adjust Full-load Minimum Injection Volume
*c Adjust Cold Starting Injection Volume
*d Adjust Boost Compensator Characteristic
*e Adjust Boost Compensator Characteristic Tendency
*f Injection Volume
*g Pump rpm
*h Boost Pressure


Apply pressure to the boost compensator.


b.

Measure the injection volume.

Pump rpm Boost pressure No. of measuring strokes Injection volume
1200 80 kPa (0.8 kgf/cm2, 12 psi) 200 11.88 to 12.28 cc (0.72 to 0.75 cu.in.)


Hide 16.CHECK HYSTERESIS (w/ BACS)

Compare the injection volume when the boost compensator pressure is lowered from 127 kPa (1.3 kgf/cm2, 18 psi) to 0 kPa (0 kgf/cm2, 0 psi) and, conversely, when it is raised from zero.

HINT:

Make measurements after moving the adjusting lever between idle and maximum 3 times for each lowering of the pressure.


Pump rpm Boost pressure No. of measuring strokes Injection volume Hysteresis
1200 80 kPa (0.8 kgf/cm2, 12 psi) 200 11.88 to 12.28 cc (0.72 to 0.75 cu.in.) -
35 kPa (0.4 kgf/cm2, 5 psi) 200 10.98 to 11.78 cc (0.67 to 0.72 cu.in.) 0.3 cc (0.02 cu.in.) or less
25 kPa (0.3 kgf/cm2, 4 psi) 200 10.28 to 11.08 cc (0.63 to 0.68 cu.in.) -
0 kPa (0 kgf/cm2, 0 psi) 200 9.82 to 10.42 cc (0.60 to 0.64 cu.in.) -

If not within the specification, check each sliding part of the boost compensator and check whether or not there is any oil.

Hide 17.ADJUST LOAD SENSING TIMER (w/o HIGH ALTITUDE)

a.
A334036C01
2.313,3.042 2.167,3.042 2.167,3.042 1.99,2.688 false 1.313,3.667 1.219,3.292 1.219,3.292 1.104,3.292 false 0.917,3.198 1.125,3.385 0.208,0.188 10 false *a 2.365,2.938 2.552,3.125 0.188,0.188 10 false *b 0.458,2.927 0.667,3.115 0.208,0.188 10 false *c 1.073,4.135 1.271,4.323 0.198,0.188 10 false *d 2.219,4.146 2.417,4.344 0.198,0.198 10 false *e 1.615,4.396 1.802,4.552 0.188,0.156 10 false *f
*a End Point of the Load Sensing Timer
*b Starting Point of the Load Sensing Timer
*c Injection Pump Inner Pressure
*d Idle Speed Side
*e Maximum Speed Side
*f Adjusting Lever Position


Using a 5 mm hexagon wrench, adjust the starting and end points of the load sensing timer by turning the governor shaft.


b.

w/ HAC:

Apply 101.1 to 101.5 kPa (758 to 761 mmHg, 29.85 to 29.97 in.Hg) absolute pressure.


c.

Measure the injection volume.

Adjusting lever position Pump rpm No. of measuring strokes
Maximum speed side 1520 200


d.
A334037

Slowly move the adjusting lever from the maximum speed side to the idle speed side, and secure it at the point where the pump inner pressure begins to drop.


e.

Measure the injection volume at the drop point (starting point).

Pump rpm No. of measuring strokes Injection volume
1520 200 Measured value at step (c)
-1.0 to 1.8 cc (0.06 to 0.11 cu.in.)


f.
A334092

Using a 5 mm hexagon wrench, adjust by turning the governor shaft, and perform the measurement again it is as specified.

HINT:

The injection volume will increase about 3 cc (0.18 cu. in.) with each 1/2 turn of the governor shaft.



g.
A334038

Check the end point injection volume by slowly moving the adjusting lever from the maximum speed side to the idle speed side, and secure it at the point where the pump inner pressure stops dropping.

Pump rpm No. of measuring strokes Injection volume
1520 200 7.58 cc (0.5 cu.in.) or more


h.

Check the timer piston fluctuation when the adjusting lever is moved from the maximum speed side to the idle speed side.

Pump rpm Timer piston fluctuation
1520 2.93 to 4.45 mm (0.115 to 0.175 in.)


i.
A334039C01
2.354,0.406 2.563,0.604 0.208,0.198 10 false *a
*a Protrusion


Check the protrusion of the governor shaft.

Protrusion:

0.5 to 2.0 mm (0.0197 to 0.0787 in.)



Hide 18.ADJUST IDLE SPEED

a.

Measure the injection volume for each pump rpm.

Adjusting lever angle Pump rpm No. of measuring strokes Injection volume Variation limit Remarks
Minus 12 to 22° 325 200 2.96 to 3.96 cc (0.18 to 0.24 cu.in.) 0.4 cc (0.02 cu.in.) Adjust
350 More than q +0.5 cc (0.03 cu.in.) - -
450 q -1.2 to 2.2 cc (0.07 to 0.13 cu.in.) -


b.
A334040

Adjust by turning the idle speed adjusting screw.


Hide 19.ADJUST COLD START SYSTEM (w/ ACSD)

a.
A334041C01
0.958,0.719 1.198,0.719 1.198,0.719 1.844,1.115 true 0.76,0.625 0.958,0.813 0.198,0.188 10 false *1
*1 Set Key


Remove the overflow screw and check the fuel temperature in the fuel pump.

Fuel temperature:

15 to 35°C (59 to 95°F)



b.

Set the key of the pump drive shaft in a vertical or horizontal position.


c.

Set the scale of the timer measuring device to zero.


d.

Check the adjusting lever opening angle and consider this angle as zero.


e.
A334042C01
1.635,1.229 1.938,0.885 1.938,0.885 2.125,0.885 false 2.156,0.781 2.365,0.969 0.208,0.188 10 false *a
*a Metal Plate


Remove the metal plate between the cold starting lever and thermo wax plunger.


f.
A334043

Turn the cold starting lever clockwise to approx. 4.9 N*m (50 kgf*cm, 43 in.*lbf) and keep the lever tightened for about 10 seconds. Then release the torque.


g.
A334044C01
2.604,1.5 2.875,1.688 0.271,0.188 10 false 20 1.333,1.5 1.604,1.688 0.271,0.188 10 false -10 1.823,1.5 2.094,1.688 0.271,0.188 10 false 0 2.188,1.5 2.458,1.688 0.271,0.188 10 false 10 0.917,1.5 1.188,1.688 0.271,0.188 10 false -20 3.01,1.5 3.281,1.688 0.271,0.188 10 false 30 0.823,1.719 1.229,1.917 0.406,0.198 10 false (-4.0) 1.26,1.719 1.677,1.917 0.417,0.198 10 false (14.0) 1.76,1.719 2.063,1.917 0.302,0.198 10 false (32) 2.167,1.719 2.479,1.917 0.313,0.198 10 false (50) 2.573,1.719 2.885,1.917 0.313,0.198 10 false (68) 2.969,1.719 3.281,1.917 0.313,0.198 10 false (86) 0.24,0.74 0.438,0.948 0.198,0.208 10 false *a 2.052,1.938 2.25,2.146 0.198,0.208 10 false *b 2.875,1.948 3.417,2.156 0.542,0.208 10 false °C (°F) 0.469,0.094 1.083,0.302 0.615,0.208 10 false mm (in.) 0.51,0.563 1.052,0.771 0.542,0.208 10 false 2 (0.08) 0.5,0.99 1.052,1.188 0.552,0.198 10 false 1 (0.04)
*a Timer Piston Stroke
*b Fuel Temperature


Measure the timer piston stroke.


h.
A334045C01
1.625,0.188 1.802,0.188 1.802,0.188 2.25,1.26 true 1.427,0.083 1.646,0.292 0.219,0.208 10 false *1
*1 Timer Adjusting Screw


Adjust by turning the timer adjusting screw.

HINT:

Screw in for stroke decrease.



Hide 20.ADJUST FAST IDLE (w/ ACSD)

a.
A334046

Measure the clearance between the adjusting lever and idle speed adjusting screw.

Fuel temperature Clearance
15°C (59°F) 1.3 mm (0.0512 in.)
30°C (86°F) 0 mm (0 in.)


b.
A334047C01
1.531,1.094 2,0.271 2,0.271 2.177,0.271 true 2.229,0.156 2.448,0.365 0.219,0.208 10 false *1
*1 Fast Idle Adjusting Screw


Adjust by turning the fast idle adjusting screw.


Hide 21. POST ADJUSTMENT CHECK

a.
A334091

Check that injection stops when the fuel cut solenoid harness is removed.

Pump revolution:

100 rpm



b.
A334013

Check the adjusting lever movement.

Adjusting lever angle:

38 to 48°



Hide 22. SEAL PARTS

a.
A334048C01
1.99,0.979 1.99,0.323 1.99,0.323 2.198,0.323 true 1.198,1.354 0.896,1.125 0.896,1.125 0.688,1.125 true 0.49,1.021 0.698,1.219 0.208,0.198 10 false *a 2.229,0.229 2.438,0.406 0.208,0.177 10 false *b
*a Full Load Set Screw with New Lead Seal
*b Maximum Speed Adjusting Screw


Seal the maximum speed adjusting screw and full load set screw with new lead seals.


Hide 23770 23.INSTALL NO. 2 NOZZLE LEAKAGE PIPE ASSEMBLY

Hide 23811 24.INSTALL FUEL FILTER TO INJECTION PUMP FUEL PIPE

Hide 22811 25.INSTALL INJECTION PUMP STAY

a.

Using a 5 mm hexagon wrench, install the injection pump stay with the 3 bolts.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)