Home › Engine / Hybrid System › 1HZ (FUEL) › FUEL INJECTION NOZZLE
RM25T0E _51 Engine / Hybrid System _029893 1HZ FUEL _0136494 FUEL INJECTION NOZZLE A

1HZ FUEL  FUEL INJECTION NOZZLE  INSTALLATION  


PROCEDURE

Hide 23600 1.INSTALL NOZZLE HOLDER AND NOZZLE SET

a.

Place 6 new injection nozzle seat gaskets and the 6 injection nozzle seats into the 6 injection nozzle holes of the cylinder head sub-assembly.


b.

Using SST, install the 6 nozzle holder and nozzle sets.

SST
09268-64010  

Torque:
63.7 N*m (650 kgf*cm, 47 ft.*lbf)

NOTICE:
·

Overtightening could cause nozzle deformation and needle adhesion or other defects.

·

When installing the injection nozzle, never tighten the nozzle holder body. Tighten the retaining nut section.




Hide 23760 2.INSTALL NOZZLE LEAKAGE PIPE ASSEMBLY

a.

Install 6 new gaskets and the nozzle leakage pipe assembly with the 6 nuts.

Torque:
29.4 N*m (300 kgf*cm, 22 ft.*lbf)


b.

Connect the fuel hose to the nozzle leakage pipe assembly, and slide the clamp to secure the hose.


Hide 23701 3.INSTALL INJECTION PIPE SUB-ASSEMBLY

a.

Temporarily install the 6 injection pipe sub-assemblies to the nozzle holder and nozzle set side and injection pump side.


b.
A329093C01
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Fulcrum length


Using a 14 mm union nut wrench, tighten the injection pipe union nut on the nozzle holder and nozzle set side.

Torque:
Specified tightening torque:

14.7 N*m (150 kgf*cm, 11 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.9843 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 12.7 N*m (130 kgf*cm, 9 ft.*lbf)




c.

Install the 3 injection pipe clamps with the 3 nuts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


d.

Using a 14 mm union nut wrench, tighten the injection pipe union nut on the injection pump side.

Torque:
Specified tightening torque:

14.7 N*m (150 kgf*cm, 11 ft.*lbf)


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 25 mm (0.9843 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 12.7 N*m (130 kgf*cm, 9 ft.*lbf)




e.

Install the 3 injection pipe clamps with the 6 nuts.

Torque:
6.4 N*m (65 kgf*cm, 57 in.*lbf)


Hide 5.BLEED INJECTION PIPE

a.

Move the priming pump in the upper part of the fuel filter assembly up and down, and fill the injection pump and fuel system with fuel.


b.

Loosen the injection pipe union nuts (in the nozzle side).


c.

Crank the engine until fuel comes out from the injection pipe union nut (in the nozzle side).


d.

Tighten the injection pipe union nut.

Click hereEngine / Hybrid System>1HZ (FUEL)>FUEL INJECTION NOZZLE>INSTALLATION


e.

Perform the procedures above for each injection pipe.