Home › Engine / Hybrid System › 1VD-FTV (COOLING) › THERMOSTAT
RM25T0E _51 Engine / Hybrid System _029897 1VD-FTV COOLING _0136550 THERMOSTAT A

1VD-FTV COOLING  THERMOSTAT  INSTALLATION  


PROCEDURE

Hide 16331A 1.INSTALL THERMOSTAT

a.
A326764C01
1.375,3.042 1.375,2.875 false 2.031,3.063 2.031,2.896 false 2.875,0.927 2.125,0.927 true 2.333,0.531 2.417,0.281 2.417,0.281 2.583,0.281 false 1.938,0.531 1.854,0.281 1.854,0.281 1.688,0.281 false 1.313,3.063 1.625,3.219 0.313,0.156 10 false *1 2.927,0.844 3.24,1 0.313,0.156 10 false *2 2.042,0.031 2.354,0.188 0.313,0.156 10 false *a 2.625,0.198 2.938,0.354 0.313,0.156 10 false *b 1.281,2.313 1.594,2.469 0.313,0.156 10 false *c 1.979,2.313 2.292,2.469 0.313,0.156 10 false *d 1.958,3.073 2.271,3.229 0.313,0.156 10 false *1 1.521,0.198 1.833,0.354 0.313,0.156 10 false *b
*1 Gasket
*2 Jiggle Valve
*a Upward
*b 30°
*c Correct
*d Incorrect


Install a new gasket to the thermostat.

HINT:

When installing the gasket to the thermostat, be careful not to deform the gasket. Make sure that the groove of the gasket is properly installed onto the thermostat as shown in the illustration.



b.

Install the thermostat with the jiggle valve facing upward.

HINT:

The jiggle valve may be set to within 30° on either side of the prescribed position.



Hide 16321 2.INSTALL WATER INLET

a.
A326765C01
2.792,0.594 3.083,0.833 0.292,0.24 10 false .
V100135

Bolt A
V100136

Bolt B


Install the water inlet with the 4 bolts.

Torque:
for bolt A : 21 N*m (214 kgf*cm, 15 ft.*lbf)
for bolt B : 24.5 N*m (250 kgf*cm, 18 ft.*lbf)


b.

Attach the clamp to connect the No. 2 oil cooler hose to the water inlet.


Hide 16603B 3.INSTALL IDLER PULLEY SUB-ASSEMBLY

a.

Install the idler pulley sub-assembly with the bolt.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


Hide 16572D 4.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the hose clamp to secure the hose.


Hide 16470 7.INSTALL RADIATOR RESERVOIR ASSEMBLY

Hide 17875 8.INSTALL INTAKE AIR CONNECTOR PIPE

Hide 17805 9.INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY

Hide 10.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

Hide 17881 12.INSTALL NO. 1 AIR CLEANER HOSE

Hide 16571C 13.INSTALL NO. 1 RADIATOR HOSE

Hide 51442 16.INSTALL NO. 2 ENGINE UNDER COVER