31301F 1.INSTALL CLUTCH PEDAL STOPPER BOLT (for 1GR-FE, 1HZ)
Install the lock nut to the clutch pedal stopper bolt.
Temporarily install the clutch pedal stopper bolt to the clutch pedal support sub-assembly.
Tighten the lock nut to the specified torque when adjusting the clutch pedal.
88280A 2.INSTALL CLUTCH SWITCH ASSEMBLY (for 1VD-FTV)
Install the lock nut to the clutch switch assembly.
Temporarily install the clutch switch assembly to the clutch pedal support sub-assembly.
Tighten the lock nut to the specified torque when adjusting the clutch pedal.
31353 3.INSTALL CLUTCH PEDAL SPRING HOLDER
|
MP grease |
Apply MP grease to the contact surface of the clutch pedal spring holder.
Install the clutch pedal spring holder to the clutch pedal support sub-assembly.
31453B 4.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH
|
MP grease |
Apply MP grease to the inside of a new clutch master cylinder push rod clevis bush.
Install the clutch master cylinder push rod clevis bush to the clutch pedal sub-assembly.
Install the clevis bush from the right side of the vehicle.
31301P 5.INSTALL CLUTCH PEDAL TURNOVER BUSH
|
MP grease |
Apply MP grease to the inside of the clutch pedal turnover bush.
Install the clutch pedal turnover bush to the clutch pedal sub-assembly.
31301B 6.INSTALL NO. 1 CLUTCH PEDAL CUSHION
Install the No. 1 clutch pedal cushion to the clutch pedal sub-assembly.
31301C 7.INSTALL CLUTCH PEDAL BUSH
|
MP grease |
Apply MP grease to the inside and outside of 2 new clutch pedal bushes.
Install the 2 clutch pedal bushes to the clutch pedal sub-assembly.
31324A 8.INSTALL CLUTCH PEDAL SHAFT COLLAR
|
MP grease |
Apply MP grease to the clutch pedal shaft collar.
Install the clutch pedal shaft collar to the clutch pedal sub-assembly.
31321 9.INSTALL CLUTCH PEDAL PAD
31301 10.INSTALL CLUTCH PEDAL SUB-ASSEMBLY
Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt and nut.
Install the bolt from the right side of the vehicle.
31301A 11.INSTALL CLUTCH PEDAL SPRING (for 1GR-FE, 1VD-FTV)
|
MP grease |
Apply MP grease to the inside and outside of the spacer and pin of the clutch pedal support sub-assembly.
Install the spacer to the clutch pedal spring.
Install the clutch pedal spring to the clutch pedal support sub-assembly with 2 new E-rings.
31301R 12.INSTALL TURN OVER SPRING SEAT COMPRESSION SPRING
|
MP grease |
Apply MP grease to the contact surfaces of the clutch pedal spring holder, clutch pedal and turn over spring seat compression spring.
Move the pedal to the full stroke position.
Install the turn over spring seat compression spring to the clutch pedal sub-assembly and clutch pedal spring holder.
13.TEMPORARILY INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY
Install the clutch pedal sub-assembly on the vehicle, and then temporarily install the bolt.
31410 14.INSTALL CLUTCH MASTER CYLINDER ASSEMBLY
Install a new gasket.
Install the clutch master cylinder assembly with the 2 nuts.
Tighten the clutch pedal support fixed bolt.
for 1VD-FTV:
Connect the clutch switch connector.
|
MP grease |
Apply MP grease to the contact surface of the clutch master cylinder push rod clevis pin.
Connect the clevis of the master cylinder to the clutch pedal with the clutch master cylinder push rod clevis pin.
Install a new clip to the clutch master cylinder push rod clevis pin.
| *a | Torque Wrench Fulcrum Length |
Using a union nut wrench, connect the clutch master cylinder to flexible hose tube.
Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 300 mm (11.811 in.)): 14.2 N*m (145 kgf*cm, 10 ft.*lbf)
55844 15.INSTALL NO. 2 HEATER TO REGISTER DUCT
55480D 16.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY
17.FILL RESERVOIR WITH BRAKE FLUID
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>BLEEDING
18.BLEED CLUTCH PIPE LINE
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>BLEEDING
19.CHECK FLUID LEVEL IN RESERVOIR
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>BLEEDING
20.CHECK FOR CLUTCH FLUID LEAK
31301 21.INSPECT AND ADJUST CLUTCH PEDAL SUB-ASSEMBLY