Home › Drivetrain › CLUTCH › CLUTCH UNIT (for 1GR-FE)
RM25T0E _52 Drivetrain _029901 CLUTCH _0136573 CLUTCH UNIT(for 1GR-FE) A

CLUTCH  CLUTCH UNIT(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C212166C02
2.729,1.354 2.833,1.104 2.833,1.104 2.969,1.104 false 3.01,1.031 3.333,1.24 0.323,0.208 10 false SST 1.646,3.156 1.875,3.375 0.229,0.219 10 false *a
*a Flywheel Side


Insert SST into the clutch disc assembly, then insert the clutch disc assembly into the flywheel sub-assembly.

SST
09301-00110  

NOTICE:

Take care not to insert the clutch disc assembly in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C173307C02
1.281,1.406 0.844,1.26 0.844,1.26 1.198,1.427 true 2.542,1.281 2.667,0.917 2.667,0.917 2.865,0.917 false 0.667,1.177 0.875,1.406 0.208,0.229 10 false *a 1.844,0.021 2.177,0.177 0.333,0.156 10 false 1,4 2.448,0.938 2.583,1.094 0.135,0.156 10 false 2 0.969,1.75 1.104,1.906 0.135,0.156 10 false 3 2.448,0.271 2.583,0.427 0.135,0.156 10 false 5 1.885,1.927 2.021,2.083 0.135,0.156 10 false 6 0.938,0.76 1.073,0.917 0.135,0.156 10 false 7 2.927,0.844 3.229,1.052 0.302,0.208 10 false SST
*a Matchmark


Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.

SST
09301-00110  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C212168N01
2.542,3.292 2.76,3.031 2.76,3.031 2.938,3.031 false 3.01,2.938 3.333,3.177 0.323,0.24 10 false SST

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

SST
09333-00013  

Maximum non-alignment:

0.5 mm (0.0197 in.)


If the alignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.
C310625

Install the release fork support to the manual transmission assembly.

Torque:
47.1 N*m (480 kgf*cm, 35 ft.*lbf)


Hide 31237 5.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT

a.
C307517

Install the clutch release fork support boot to the clutch release fork sub-assembly.


Hide 31204 6.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C163041C02
0,0 0,0 false
V100135

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)


Apply release hub grease to the clutch release fork sub-assembly, clutch release bearing assembly, push rod contact point and pivot points shown in the illustration.

Grease:

Toyota Genuine Clutch Release Hub Grease or equivalent (mineral ingredients should not be included)



b.
C212169C02
0,0 0,0 false
V100135

Toyota Genuine Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



c.
C163036

Install the clutch release bearing assembly to the clutch release fork sub-assembly with the release bearing hub clip.


d.
C311968

Install the clutch release fork sub-assembly with the clutch release bearing assembly to the manual transmission assembly.

NOTICE:

After installation, move the fork back and forth to check that the release bearing slides smoothly.