Home › Drivetrain › H150F (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSMISSION ASSEMBLY (for 1GR-FE) › 2014.08–2022.09
RM25T0E _52 Drivetrain _029902 H150F MANUAL TRANSMISSION / TRANSAXLE _0137560 MANUAL TRANSMISSION ASSEMBLY(for 1GR-FE) A

H150F MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSMISSION ASSEMBLY(for 1GR-FE)  INSTALLATION  


PROCEDURE

Hide 31236B 1.INSTALL RELEASE FORK SUPPORT

Hide 31237 2.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT

Hide 31204 3.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

Hide 4.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C314388C01
0.615,0.969 0.927,1.167 0.313,0.198 10 false *a 1.823,0.948 2.135,1.146 0.313,0.198 10 false *b
*a for Type A
*b for Type B


Install the air fuel ratio sensor bracket LH with the bolt.

Torque:
for Type A : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
for Type B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


b.
C314389C01
0.625,0.948 0.938,1.146 0.313,0.198 10 false *a 1.833,0.927 2.146,1.125 0.313,0.198 10 false *b
*a for Type A
*b for Type B


Install the air fuel ratio sensor bracket RH with the bolt.

Torque:
for Type A : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
for Type B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


c.
C314390C01
0.604,0.938 0.917,1.135 0.313,0.198 10 false *a 1.833,0.927 2.146,1.125 0.313,0.198 10 false *b
*a for Type A
*b for Type B


Install the heated oxygen sensor bracket RH with the bolt.

Torque:
for Type A : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
for Type B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


d.
C314391C01
1.854,0.917 2.167,1.115 0.313,0.198 10 false *b 0.635,0.917 0.948,1.115 0.313,0.198 10 false *a
*a for Type A
*b for Type B


Install the heated oxygen sensor bracket LH with the bolt.

Torque:
for Type A : 7.5 N*m (76 kgf*cm, 66 in.*lbf)
for Type B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


e.
C312649

Install the 2 wire harness clamp brackets with the 2 bolts.

Torque:
8.0 N*m (82 kgf*cm, 71 in.*lbf)


Hide 5.INSTALL TRANSFER ASSEMBLY

C161482

a.

Install the transfer assembly to the manual transmission with the 6 bolts.

Torque:
68.6 N*m (700 kgf*cm, 51 ft.*lbf)


Hide 36112B 6.CONNECT REAR NO. 1 TRANSFER CASE HOSE

a.
C312891

Connect the rear No. 1 transfer case hose to the manual transmission and slide the clip to secure it.


b.

Connect the clamp.


Hide 7.INSTALL MANUAL TRANSMISSION WITH TRANSFER

C213823E02
0.61,0.325 0.736,0.491 0.126,0.165 10 A 1.181,0.022 1.307,0.187 0.126,0.165 10 A 2.167,0.109 2.293,0.274 0.126,0.165 10 A 2.619,0.548 2.745,0.714 0.126,0.165 10 A 2.802,1.432 2.928,1.598 0.126,0.165 10 A 0.464,1.54 0.595,1.686 0.131,0.146 10 B 0.847,1.812 0.978,1.958 0.131,0.146 10 B 2.384,1.849 2.515,1.995 0.131,0.146 10 B 2.685,1.678 2.816,1.823 0.131,0.146 10 B

a.

Install the manual transmission with transfer with the 9 bolts.

Torque:
for Bolt A : 71.6 N*m (730 kgf*cm, 53 ft.*lbf)
for Bolt B : 37.3 N*m (380 kgf*cm, 28 ft.*lbf)

NOTICE:

Make sure that the knock pins are not loose, bent, damaged or scratched, and that the contact surfaces of the engine and manual transmission are flush when installing the manual transmission to the engine.



Hide 8.CONNECT WIRE HARNESS

a.

Connect the connectors and clamps, and then connect the wire harness to the manual transmission.


b.

Tilt up the manual transmission with transfer.


c.
C312650

Install the clamp and connect the wire harness to the manual transmission with transfer.


d.
C213830

Connect the No. 2 cable bond with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 12371 9.INSTALL REAR ENGINE MOUNTING INSULATOR

C161536

a.

Install the rear engine mounting insulator to the manual transmission with transfer with the 4 bolts.

Torque:
59 N*m (602 kgf*cm, 44 ft.*lbf)


Hide 51203 10.INSTALL NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

a.
C312481C01
0,0 0,0 false
V100135

Nut
V100136

Bolt


Install the No. 2 frame crossmember sub-assembly with the 2 nuts and 8 bolts.

Torque:
for Nut : 74 N*m (755 kgf*cm, 55 ft.*lbf)
for Bolt : 46 N*m (469 kgf*cm, 34 ft.*lbf)


Hide 11.INSTALL FRONT STABILIZER BRACKET LH

a.

Install the front stabilizer bracket LH with the 2 bolts.

Torque:
29.7 N*m (303 kgf*cm, 22 ft.*lbf)


Hide 12.INSTALL FRONT STABILIZER BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 31470 13.CONNECT CLUTCH RELEASE CYLINDER ASSEMBLY

a.
C213829N01
1.865,3.198 1.979,3.354 0.115,0.156 10 false B 1.354,2.927 1.469,3.083 0.115,0.156 10 true B 1.313,0.125 1.469,0.323 0.156,0.198 10 true A 1.896,0.625 2.052,0.823 0.156,0.198 10 true A

Connect the clutch release cylinder assembly with the 4 bolts.

Torque:
for Bolt A : 20 N*m (204 kgf*cm, 15 ft.*lbf)
for Bolt B : 11.8 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 31121 14.INSTALL NO. 1 CLUTCH HOUSING COVER

Hide 28100 15.INSTALL STARTER ASSEMBLY

Hide 37110 16.INSTALL REAR PROPELLER SHAFT ASSEMBLY

Hide 37140 17.INSTALL FRONT PROPELLER SHAFT ASSEMBLY

Hide 17118 18.INSTALL NO. 1 EXHAUST MANIFOLD STAY

Hide 17410 20.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Model Code #J78, #J79 Series)

Hide 17410 21.INSTALL FRONT EXHAUST PIPE ASSEMBLY (for Model Code #J71, #J76 Series)

Hide 51447C 22.INSTALL TRANSFER CASE PROTECTOR

C213828

a.

Install the transfer case protector to the No. 2 frame crossmember sub-assembly with the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 17705 24.INSTALL AIR CLEANER CAP SUB-ASSEMBLY WITH NO. 1 AIR CLEANER HOSE

Hide 16571C 26.INSTALL NO. 1 RADIATOR HOSE

Hide 36308 27.CONNECT HIGH AND LOW SHIFT ROD SUB-ASSEMBLY

a.

Connect the high and low shift rod sub-assembly with the washer and nut.

Torque:
11.76 N*m (120 kgf*cm, 9 ft.*lbf)


Hide 29.INSPECT AND ADJUST TRANSFER SHIFT LEVER ASSEMBLY

Hide 33530F 30.INSTALL TRANSMISSION SHIFT LEVER ASSEMBLY

C313779C02
0.594,1.615 0.885,1.615 0.885,1.615 1.125,1.094 true 0.313,1.542 0.656,1.76 0.344,0.219 11 false *a
*a Cloth or Equivalent
V100135

Down
V100136

Clockwise


a.

Cover the transmission shift lever cap with a cloth or equivalent.


b.

While pressing down on the transmission shift lever cap, turn it clockwise to install the transmission shift lever.


Hide 58286 31.INSTALL NO. 1 SHIFT AND SELECT LEVER BOOT

Hide 36303 32.INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

Hide 89441A 33.INSTALL DECELERATION SENSOR (w/ ABS)

Hide 89170 34.INSTALL AIRBAG SENSOR ASSEMBLY WITH AIRBAG SENSOR BRACKET (w/ Airbag System)

Hide 62111A 39.INSTALL COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 67913 41.INSTALL FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 43.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 51442 48.INSTALL NO. 2 ENGINE UNDER COVER