Home › Drivetrain › CLUTCH › CLUTCH UNIT (for 1VD-FTV) › 2014.08–2016.08
RM25T0E _52 Drivetrain _029901 CLUTCH _0136574 CLUTCH UNIT(for 1VD-FTV) A

CLUTCH  CLUTCH UNIT(for 1VD-FTV)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C310621C01
2.125,1.313 2.281,0.896 2.281,0.896 2.542,0.896 true 1.073,3.333 1.385,3.531 0.313,0.198 10 false *a 2.604,0.823 3.031,1.031 0.427,0.208 10 false SST
*a Flywheel Side


Insert SST into the clutch disc assembly, then insert them into the flywheel sub-assembly.

SST
09301-00120  

NOTICE:

Take care not to insert the clutch disc assembly in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C163025C01
2.49,1.333 2.896,0.906 false 1.281,0.729 0.948,0.24 0.948,0.24 1.198,0.719 true 2.969,0.802 3.323,1.01 0.354,0.208 10 false SST 0.76,0.156 1.094,0.354 0.333,0.198 10 false *a 1.396,0 1.729,0.188 0.333,0.188 10 false 1,5 2.073,1.948 2.427,2.146 0.354,0.198 10 false 2,6 0.573,1.396 0.74,1.594 0.167,0.198 10 false 9 2.594,0.479 2.76,0.677 0.167,0.198 10 false 10 0.646,0.646 0.802,0.844 0.156,0.198 10 false 7 2.615,0.833 2.781,1.01 0.167,0.177 10 false 8 1.24,1.906 1.417,2.104 0.177,0.198 10 false 4 2.083,0.01 2.302,0.219 0.219,0.208 10 false 3
*a Matchmark


Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Following the order shown in the illustration, tighten the 8 bolts, starting with the bolt located near the knock pin at the top.

SST
09301-00120  

Torque:
39.2 N*m (400 kgf*cm, 29 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C163042

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum misalignment:

0.5 mm (0.0197 in.)



b.
C163043E01
2.954,0.654 3.314,0.838 0.36,0.184 10 SST 2.478,1.169 2.911,0.76 false

If the alignment is not as specified, adjust the diaphragm spring tip alignment using SST.

SST
09333-00013  


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.
C310620

Install the release fork support to the manual transmission assembly.

Torque:
47.1 N*m (480 kgf*cm, 35 ft.*lbf)


Hide 31237 5.INSTALL CLUTCH RELEASE FORK SUPPORT BOOT

a.
C307517

Install the clutch release fork support boot to the clutch release fork sub-assembly.


Hide 31204 6.INSTALL CLUTCH RELEASE FORK SUB-ASSEMBLY

a.
C163041C02
0,0 0,0 false
V100135

Multemp 8158 grease or equivalent


Apply release hub grease to the clutch release fork sub-assembly, clutch release bearing assembly, push rod contact point and pivot points shown in the illustration.

Grease:

Multemp 8158 grease or equivalent



b.
C310622C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft spline.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



c.
C163036

Install the clutch release bearing assembly to the clutch release fork sub-assembly with the release bearing hub clip.


d.
C310619

Install the clutch release fork sub-assembly with the clutch release bearing assembly to the manual transmission assembly.

NOTICE:

After installation, move the fork back and forth to check that the release bearing slides smoothly.