Home › Drivetrain › CLUTCH › CLUTCH UNIT (for 1HZ)
RM25T0E _52 Drivetrain _029901 CLUTCH _0136647 CLUTCH UNIT(for 1HZ) A

CLUTCH  CLUTCH UNIT(for 1HZ)  INSTALLATION  


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

a.
C226320C01
1.667,0.917 1.75,0.667 1.75,0.667 2,0.667 false 2.042,0.583 2.5,0.781 0.458,0.198 10 false SST 2.167,0.927 2.625,1.125 0.458,0.198 10 false *a
*a Flywheel Side


Insert SST into the clutch disc assembly, then insert the clutch disc into the flywheel sub-assembly.

SST
09301-00110  

NOTICE:

Take care not to insert the clutch disc assembly in the wrong direction.



Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C215535C01
0.823,1.365 0.427,1.167 0.427,1.167 0.885,1.323 false 2.813,1.229 2.563,1.229 2.563,1.229 2.271,0.969 false 0.271,1.094 0.583,1.292 0.313,0.198 10 false *a 2.865,1.146 3.177,1.344 0.313,0.198 10 false SST 0.625,0.125 0.938,0.323 0.313,0.198 10 false 1,4 2.427,0.188 2.74,0.385 0.313,0.198 10 false 5 2.615,1.313 2.927,1.51 0.313,0.198 10 false 2 2.292,1.927 2.604,2.125 0.313,0.198 10 false 6 0.677,1.833 0.99,2.031 0.313,0.198 10 false 3 0.396,0.729 0.708,0.927 0.313,0.198 10 false 7
*a Matchmark


Align the matchmarks on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Following the order shown in the illustration, tighten the 6 bolts, starting with the bolt located near the knock pin at the top.

SST
09301-00110  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C215536N01
1.844,3.208 2.052,2.469 2.052,2.469 2.344,2.469 false 2.396,2.396 2.854,2.594 0.458,0.198 10 false SST

Using a dial indicator with a roller instrument, measure the diaphragm spring tip alignment.

SST
09333-00013  

Maximum misalignment:

0.5 mm (0.0196 in.)


If the alignment is more than the maximum, using SST, adjust the diaphragm spring tip alignment.


Hide 31236B 4.INSTALL RELEASE FORK SUPPORT

a.
C310617

Install the release fork support to the manual transmission assembly.

Torque:
47 N*m (479 kgf*cm, 35 ft.*lbf)


Hide 31230 5.INSTALL CLUTCH RELEASE BEARING ASSEMBLY

a.

Install the release bearing hub clip to the clutch release bearing assembly.


b.
C215537C01
0,0 0,0 false
V100135

Multemp 8158 grease or equivalent


Apply release hub grease to the clutch release fork sub-assembly, clutch release bearing assembly, push rod contact point and pivot points shown in the illustration.

Grease:

Multemp 8158 grease or equivalent



c.

Install the release fork sub-assembly to the clutch release bearing assembly.


d.

Install the clutch release bearing assembly together with the clutch release fork sub-assembly to the clutch housing.

NOTICE:

After the installation, move the fork forward and backward to check that the release bearing slides smoothly.



e.
C310616C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply the clutch spline grease to the spline of the input shaft.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31126 6.INSTALL CLUTCH RELEASE FORK BOOT