Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT DIFFERENTIAL CARRIER ASSEMBLY (for Standard) › 2014.08–2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0136706 FRONT DIFFERENTIAL CARRIER ASSEMBLY(for Standard) A

AXLE AND DIFFERENTIAL  FRONT DIFFERENTIAL CARRIER ASSEMBLY(for Standard)  DISASSEMBLY  


PROCEDURE

Hide 41204D 1.INSPECT RUNOUT OF FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY

a.
C236648C02
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 30 mm (1.18 in.)


Using a dial indicator, measure the runout of the front drive pinion companion flange sub-assembly vertically and laterally.

Maximum Runout:
Item Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the front drive pinion companion flange sub-assembly.



Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C161257

Using a dial indicator, measure the runout of the ring gear.

Maximum runout:

0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the ring gear with a new one.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161258

Using a dial indicator, measure the backlash of the ring gear.

Standard backlash:

0.13 to 0.18 mm (0.00512 to 0.00708 in.)


HINT:

Measure at 3 or more positions around the circumference of the ring gear.

If the backlash is not as specified, adjust the side bearing preload or repair as necessary.



Hide 4.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH (for 2 Pinion Gear Type)

a.
C161260

Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the case.

Standard backlash:

0.05 to 0.20 mm (0.00197 to 0.00787 in.)


If the backlash is not within the specification, replace the side gear thrust washer with one of a different thickness.


Hide 5.INSPECT DRIVE PINION PRELOAD

a.
C161259

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard drive pinion preload (at starting):

0.56 to 0.85 N*m (6 to 8 kgf*cm, 5 to 7 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 6.INSPECT TOTAL PRELOAD

a.
C161259

Using a torque wrench, measure the total preload with the teeth of the drive pinion and ring gear in contact.

Standard drive pinion preload (at starting):

0.39 to 0.59 N*m (4 to 6 kgf*cm, 4 to 5 in.*lbf) + Standard drive pinion preload


If necessary, disassemble and inspect the differential.


Hide 41204E 7.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT

Hide 41204D 8.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41252A 9.REMOVE FRONT DIFFERENTIAL DUST DEFLECTOR

a.
C311241N01
1.948,2.542 2.406,2.323 2.406,2.323 1.885,2.271 false 1.104,2.469 1.417,2.74 false 2.479,2.25 2.938,2.448 0.458,0.198 10 false SST 0.802,2.375 1.26,2.573 0.458,0.198 10 false SST

Using SST and press, press out the front differential dust deflector.

SST
09950-00020  
09950-60010  (09951-00440)
09950-70010  (09951-07100)

NOTICE:

Do not drop the front drive pinion companion flange sub-assembly.



Hide 41101D 10.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL

Hide 41214C 11.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41211B 12.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C124133N06
1.662,0.743 0.99,0.509 false 0.603,0.43 0.897,0.573 0.294,0.143 10 SST

Using SST, remove the front drive pinion rear tapered roller bearing (inner race).

SST
09556-22010  


Hide 41316A 13.REMOVE FRONT DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C161272

Remove the 2 bolts and 2 front differential bearing adjusting nut locks.


Hide 41311 14.REMOVE FRONT DIFFERENTIAL CASE

a.
C161273C01
1.323,1.698 0.781,1.5 0.781,1.5 1.313,1.594 true 0.594,1.406 0.781,1.604 0.188,0.198 10 true *a
*a Matchmark


Place matchmarks on the bearing caps and differential carrier.


b.

Remove the 4 bolts, 2 bearing caps and 2 front differential bearing adjusting nuts.


c.
C161274

Remove the front differential case and 2 front differential case bearings (outer race) from the differential carrier.

HINT:
C161275N02
1.156,1.333 1.365,1.5 0.208,0.167 10 LH 2.54,1.329 2.766,1.496 0.226,0.167 10 RH

Tag the 2 front differential case bearing outer races to show the locations for reassembly.



Hide 15.REMOVE DIFFERENTIAL DRIVE PINION

a.
C161277

Remove the differential drive pinion from the differential carrier.


Hide 41231F 16.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41211A 17.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C311242N01
1.5,1.615 1.75,1.781 1.75,1.781 2,1.781 false 2.073,1.708 2.531,1.906 0.458,0.198 10 false SST

Using SST and a press, press out the front drive pinion front tapered roller bearing (inner race).

SST
09950-00020  

If either the differential drive pinion or differential ring gear is damaged, replace them as a set.


Hide 18.REMOVE FRONT DIFFERENTIAL DRIVE PINION PLATE WASHER

Hide 41211B 19.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C161279N02
2.422,0.876 2.722,1.024 0.3,0.148 10 SST 2.413,0.961 1.864,0.961 false 1.864,0.961 1.864,1.12 false

Using SST, tap out the front drive pinion rear tapered roller bearing (outer race).

SST
09308-00010  

If the front drive pinion rear tapered roller bearing is damaged during removal, replace it.


Hide 41211A 20.REMOVE FRONT DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161280

Using a brass bar and hammer, tap out the front drive pinion front tapered roller bearing (outer race).

If the front drive pinion front tapered roller bearing is damaged during removal, replace it.


Hide 41115F 21.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING

a.
C162081

Using a hammer and brass bar, tap out the front differential oil storage ring.


Hide 22.REMOVE DIFFERENTIAL RING GEAR

a.
C316143

Using a screwdriver, unstake the lock plates.


b.
C161282C01
0.875,1.104 1.292,1.646 1.292,1.646 0.823,1.156 true 1.344,1.594 2.063,1.75 0.719,0.156 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and front differential case.


c.

Remove the 10 bolts and 5 lock plates.


d.
C161283

Using a plastic-faced hammer, tap on the differential ring gear to separate it from the front differential case.


Hide 41311 23.INSPECT RUNOUT OF FRONT DIFFERENTIAL CASE

HINT:

If the differential ring gear runout is at the maximum or less, this inspection is not necessary.


a.

Install the 2 front differential case bearings (outer race) to the front differential case.


b.

Install the front differential case to the differential carrier.


c.

Install the 2 front differential bearing adjusting nuts.


d.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
85.3 N*m (870 kgf*cm, 63 ft.*lbf)


e.
C236665

Inspect the differential case runout.

Maximum runout:

0.04 mm (0.00157 in.)



f.

Remove the 4 bolts and 2 bearing caps.


g.

Remove the 2 front differential bearing adjusting nuts.


h.

Remove the front differential case.


i.

Remove the 2 front differential case bearings (outer race).


Hide 41311A 24.REMOVE FRONT DIFFERENTIAL CASE BEARING

HINT:

The differential case and case bearings should only be removed when replacement is necessary.


a.
C282338C01
0.781,0.479 1.135,0.479 1.135,0.479 1.135,0.76 false 2.781,1.542 2.781,2.083 2.781,2.083 3.031,2.083 true 0.458,0.396 0.917,0.594 0.458,0.198 10 false SST 3.073,1.958 3.281,2.177 0.208,0.219 10 false *a 2.625,0.24 2.833,0.458 0.208,0.219 10 false *b 0.219,1.292 0.427,1.51 0.208,0.219 10 false *c
*a Notch
*b Turn
*c Hold


Using SST, remove the 2 front differential case bearings (inner race) from the front differential case.

SST
09950-60010  (09951-00480)
09950-40011  (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04061, 09958-04011)

HINT:

Attach the claws of SST to the notch in the front differential case to secure SST.



Hide 41311 25.DISASSEMBLE FRONT DIFFERENTIAL CASE (for 2 Pinion Gear Type)

a.
C161333

Using a pin punch and hammer, tap out the straight pin.


b.
C236670C01
0.948,0.656 1,0.417 1,0.417 1.167,0.417 false 2.49,1.281 2.542,1.042 2.542,1.042 2.708,1.042 false 0.615,0.573 0.667,0.333 0.667,0.333 0.833,0.333 false 2.823,1.448 2.875,1.208 2.875,1.208 3.042,1.208 false 1.635,1.208 1.688,1.469 1.688,1.469 1.854,1.469 false 1.292,1.625 1.427,1.802 1.427,1.802 1.594,1.802 false 0.813,1.865 0.948,2.042 0.948,2.042 1.115,2.042 false 1.76,0.365 1.844,0.365 1.844,0.365 1.927,0.531 false 2.729,0.479 2.781,0.24 2.781,0.24 2.948,0.24 false 1.229,0.354 1.542,0.552 0.313,0.198 10 false *1 2.771,0.969 3.083,1.167 0.313,0.198 10 false *1 0.854,0.25 1.167,0.448 0.313,0.198 10 false *2 3.094,1.135 3.406,1.333 0.313,0.198 10 false *2 1.917,1.406 2.229,1.604 0.313,0.198 10 false *3 1.667,1.729 1.979,1.927 0.313,0.198 10 false *4 1.177,1.969 1.49,2.167 0.313,0.198 10 false *5 1.594,0.292 1.906,0.49 0.313,0.198 10 false *4 3,0.177 3.313,0.375 0.313,0.198 10 false *5
*1 Front Differential Pinion
*2 Front Differential Pinion Thrust Washer
*3 Front No. 1 Differential Pinion Shaft
*4 Front Differential Side Gear
*5 Front No. 1 Differential Side Gear Thrust Washer


Remove the 2 front differential pinions, 2 front differential pinion thrust washers, 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and front No. 1 differential pinion shaft from the front differential case.


Hide 41311 26.DISASSEMBLE FRONT DIFFERENTIAL CASE (for 4 Pinion Gear Type)

a.
C161340C01
1.219,1.458 2.208,1.677 false 2.208,1.677 1.219,1.552 false 2.229,1.604 2.969,1.76 0.74,0.156 10 false *a
*a Matchmark


Place matchmarks on the front differential case LH and RH.


b.

Remove the 8 bolts uniformly, a little at a time.


c.

Using a plastic-faced hammer, separate the front differential case LH and RH.


d.
C161341C01
1,0.906 0.542,0.906 false 2.375,1.198 2.688,1.198 false 2.833,1.573 3.021,1.573 false 0.583,0.49 0.354,0.49 false 1.875,0.573 2.438,0.479 2.438,0.479 2.333,0.792 false 1.844,0.281 2.969,0.188 2.969,0.188 2.677,0.771 false 1.604,1.667 1.125,1.615 1.125,1.615 1.188,1.438 false 1.635,1.896 0.531,1.854 0.531,1.854 0.896,1.406 false 1.688,0.896 1.281,0.188 1.281,0.188 1.094,0.188 false 0.365,0.823 0.563,0.979 0.198,0.156 10 false *4 2.781,1.115 2.979,1.271 0.198,0.156 10 false *4 3.052,1.469 3.25,1.656 0.198,0.188 10 false *5 0.198,0.396 0.396,0.583 0.198,0.188 10 false *5 0.917,0.125 1.115,0.313 0.198,0.188 10 false *3 2.479,0.323 2.698,0.51 0.219,0.188 10 false *1 0.969,1.552 1.167,1.74 0.198,0.188 10 false *1 0.333,1.75 0.531,1.938 0.198,0.188 10 false *2 3.021,0.063 3.229,0.25 0.208,0.188 10 false *2
*1 Front Differential Pinion
*2 Front Differential Pinion Thrust Washer
*3 Front Differential Spider
*4 Front Differential Side Gear
*5 Front No. 1 Differential Side Gear Thrust Washer


Remove the 4 front differential pinions, 4 front differential pinion thrust washers, 2 front differential side gears, 2 front No. 1 differential side gear thrust washers and front differential spider from the front differential case.