1.DRAIN DIFFERENTIAL OIL
37140 2.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
41204E 3.REMOVE FRONT DRIVE PINION COMPANION FLANGE NUT
Using SST and a hammer, loosen the staked part of the front drive pinion companion flange nut.
| *a | Turn |
| *b | Hold |
Using SST, hold the front drive pinion companion flange sub-assembly, and remove the front drive pinion companion flange nut.
41204D 4.REMOVE FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
Using SST, remove the front drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
41101D 5.REMOVE FRONT DIFFERENTIAL CARRIER OIL SEAL
Using SST, remove the front differential carrier oil seal.
41214C 6.REMOVE FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
Remove the front differential drive pinion oil slinger from the differential drive pinion.
41211B 7.REMOVE FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST, remove the front drive pinion rear tapered roller bearing (inner race).
Using SST, tap out the front drive pinion rear tapered roller bearing (outer race).
41115F 8.REMOVE FRONT DIFFERENTIAL OIL STORAGE RING
Using a screwdriver and hammer, tap out the front differential oil storage ring.
41231F 9.REMOVE FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Remove the front differential drive pinion bearing spacer from the differential drive pinion.
41231F 10.INSTALL FRONT DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new front differential drive pinion bearing spacer.
Make sure the front differential drive pinion bearing spacer is installed correctly.
41115F 11.INSTALL FRONT DIFFERENTIAL OIL STORAGE RING
Using a brass bar and hammer, tap in a new front differential oil storage ring.
Be careful not to damage the front differential oil storage ring.
41211B 12.INSTALL FRONT DRIVE PINION REAR TAPERED ROLLER BEARING
Using SST and a hammer, install the front drive pinion rear tapered roller bearing (outer race).
Install the front drive pinion rear tapered roller bearing (inner race).
41214C 13.INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER
Install the front differential drive pinion oil slinger to the differential drive pinion.
41101D 14.INSTALL FRONT DIFFERENTIAL CARRIER OIL SEAL
| *a | Oil Seal Depth |
Using SST and a hammer, tap in a new front differential carrier oil seal.
0.55 to 1.45 mm (0.0217 to 0.0570 in.)
Apply MP grease to the lip of the front differential carrier oil seal.
41204D 15.INSTALL FRONT DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
Using SST, install the front drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
Apply hypoid gear oil LSD to the drive pinion threads and nut seat face.
| *a | Turn |
| *b | Hold |
Using SST, hold the front drive pinion companion flange sub-assembly.
Using a 30 mm socket wrench and torque wrench, gradually tighten the front drive pinion companion flange nut within the adjustment range of the differential drive pinion preload.
or less
Apply hypoid gear oil LSD to the drive pinion threads and front drive pinion companion flange front nut seat face.
16.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Using a torque wrench, measure the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 1.05 to 1.64 N*m (11 to 16 kgf*cm, 10 to 14 in.*lbf) |
| Reused bearing | 0.56 to 0.85 N*m (6 to 8 kgf*cm, 5 to 7 in.*lbf) |
If the result is not as specified, adjust the preload.
for Standard: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT DIFFERENTIAL CARRIER ASSEMBLY (for Standard)>REASSEMBLY
w/ Differential Lock: Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT DIFFERENTIAL CARRIER ASSEMBLY (w/ Differential Lock)>REASSEMBLY
41204E 17.STAKE FRONT DRIVE PINION COMPANION FLANGE NUT
Using a chisel and hammer, stake the front drive pinion companion flange nut.
37140 18.INSTALL FRONT PROPELLER SHAFT ASSEMBLY
19.ADD DIFFERENTIAL OIL