Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(for Standard) › 2014.08–2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0136708 REAR DIFFERENTIAL CARRIER ASSEMBLY(for Standard) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(for Standard)  DISASSEMBLY  


PROCEDURE

Hide 1.INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE

a.
C236648C09
2.479,1.813 2.656,1.969 0.177,0.156 10 false *a
*a 35 mm (1.38 in.)


Using a dial indicator, measure the runout of the companion flange vertically and laterally.

Maximum Runout:
Runout Specified Condition
Vertical runout 0.10 mm (0.00394 in.)
Lateral runout 0.10 mm (0.00394 in.)


If the runout is more than the maximum, replace the companion flange.


Hide 2.INSPECT RUNOUT OF DIFFERENTIAL RING GEAR

a.
C161834

Using a dial indicator, measure the ring gear runout.

Maximum runout:

0.05 mm (0.00197 in.)


If the runout is more than the maximum, replace the ring gear.


Hide 3.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161835

Using a dial indicator, measure the ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

HINT:

Measure at 3 or more positions around the circumference of the ring gear.



Hide 4.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD

a.
C161259

Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

Standard drive pinion preload (at starting):

0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)


If necessary, disassemble and inspect the differential.


Hide 41204G 5.REMOVE REAR DRIVE PINION COMPANION FLANGE NUT

Hide 41204 6.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41201C 7.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL

Hide 41214 8.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 9.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C124133N08
1.662,0.743 0.99,0.509 false 0.603,0.43 0.897,0.573 0.294,0.143 10 SST

Using SST, remove the rear drive pinion front tapered roller bearing (inner race) from the differential drive pinion.

SST
09556-22010  

If the rear drive pinion front tapered roller bearing is damaged or worn, replace the rear drive pinion front tapered roller bearing.


Hide 41316 10.REMOVE REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK

a.
C161838

Remove the 2 bolts and 2 rear differential bearing adjusting nut locks.


Hide 11.REMOVE DIFFERENTIAL CASE ASSEMBLY

a.
C161903C01
1.667,1.51 1.021,1.854 1.021,1.854 1.708,1.625 true 0.823,1.781 1.135,1.979 0.313,0.198 10 false *a
*a Matchmark


Place matchmarks on the bearing caps and differential carrier.


b.

Remove the 4 bolts, 2 bearing caps and 2 rear differential bearing adjusting nuts.


c.
C161275N04
1.156,1.333 1.365,1.5 0.208,0.167 10 LH 2.54,1.329 2.766,1.496 0.226,0.167 10 RH

Remove the differential case and 2 rear differential case bearings (outer race) from the differential carrier.

HINT:

Tag the 2 rear differential case bearings (outer race) to show the location for reassembly.



Hide 12.REMOVE DIFFERENTIAL DRIVE PINION

a.

Remove the differential drive pinion from the differential carrier.


Hide 41231 13.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

a.

Remove the rear differential drive pinion bearing spacer from the differential carrier.


Hide 41201A 14.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C237656N06
2.731,0.394 3.04,0.551 0.309,0.157 10 SST 2.334,1.03 2.605,0.467 2.605,0.467 2.697,0.467 false

Using SST and a press, press out the rear drive pinion rear tapered roller bearing (inner race).

SST
09950-00020  

If either the drive pinion or ring gear is damaged, replace them as a set.


Hide 41201D 15.REMOVE REAR DIFFERENTIAL DRIVE PINION PLATE WASHER

a.

Remove the rear differential drive pinion plate washer from the differential drive pinion.


Hide 41201B 16.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161839

Using a brass bar and hammer, tap out the rear drive pinion front tapered roller bearing (outer race).


Hide 41201A 17.REMOVE REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162552

Using a brass bar and hammer, tap out the rear drive pinion rear tapered roller bearing (outer race).


Hide 18.REMOVE DIFFERENTIAL RING GEAR

a.
C161840C01
1.24,1.313 2.167,1.208 2.167,1.208 1.219,1.458 true 2.208,1.125 2.969,1.292 0.76,0.167 10 false *a
*a Matchmark


Place matchmarks on the differential ring gear and differential case.


b.

Remove the 12 differential ring gear set bolts.


c.

Using a plastic-faced hammer, tap on the differential ring gear to separate it from the differential case.


Hide 19.INSPECT RUNOUT OF DIFFERENTIAL CASE

HINT:

If the differential ring gear runout is at the maximum or less, this inspection is not necessary.


a.

Install the 2 rear differential case bearings (outer race) to the differential case.


b.

Install the differential case to the differential carrier.


c.

Install the 2 rear differential bearing adjusting nuts.


d.

Install the 2 bearing caps to the differential carrier with the 4 bolts.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)


e.
C161904

Using a dial indicator, measure the differential case runout.

Maximum runout:

0.04 mm (0.00157 in.)



f.

Remove the 4 bolts and 2 bearing caps.


g.

Remove the 2 rear differential bearing adjusting nuts.


h.

Remove the differential case.


i.

Remove the 2 rear differential case bearings (outer race).


Hide 41301A 20.REMOVE REAR DIFFERENTIAL CASE BEARING

a.
C161842N03
1.912,1.161 2.493,1.045 2.493,1.045 2.175,1.279 false 2.523,0.945 2.837,1.094 0.314,0.148 10 SST 2.493,1.045 2.138,0.87 false

Using SST, remove the 2 rear differential case bearings from the differential case.

SST
09950-00020  
09950-00030  
09950-40011  (09957-04010)
09950-60010  (09951-00480)


Hide 21.DISASSEMBLE DIFFERENTIAL CASE

a.
C161843C01
1.885,1.344 2.625,0.979 2.625,0.979 1.896,1.469 true 2.646,0.896 2.927,1.146 0.281,0.25 10 false *a
*a Matchmark


Place matchmarks on the differential case LH and RH.


b.

Remove the 8 bolts uniformly, a little at a time.


c.

Using a plastic-faced hammer, separate the differential case LH and RH.


d.

Remove the 2 rear No. 1 differential side gear thrust washers, 2 rear differential side gears, rear differential spider, 4 rear differential pinions and 4 rear differential pinion thrust washers.