37110 1.REMOVE PROPELLER SHAFT ASSEMBLY
41204G 2.REMOVE REAR DRIVE PINION COMPANION FLANGE NUT
Using SST and a hammer, loosen the staked part of the rear drive pinion companion flange nut.
| *a | Turn |
| *b | Hold |
Using SST, hold the rear drive pinion companion flange sub-assembly in place, remove the rear drive pinion companion flange nut.
41204 3.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
Using SST, remove the rear drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
41201C 4.REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL
Using SST, remove the rear differential carrier oil seal.
41214 5.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
Remove the rear differential drive pinion oil slinger from the differential drive pinion.
41201B 6.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
Using SST, remove the rear drive pinion front tapered roller bearing (inner race).
Using SST, tap out the rear drive pinion front tapered roller bearing (outer race).
41231 7.REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Remove the rear differential drive pinion bearing spacer from the differential drive pinion.
41231 8.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER
Install a new rear differential drive pinion bearing spacer.
Make sure the spacer is installed correctly.
41201B 9.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING
Using SST and a hammer, tap in the rear drive pinion front tapered roller bearing (outer race).
Install the rear drive pinion front tapered roller bearing (inner race).
41214 10.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER
Install the rear differential drive pinion oil slinger to the differential drive pinion.
41201C 11.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL
| *A | Type A |
| *B | Type B |
| *1 | Dust Deflector |
The tap-in depth for the rear differential carrier oil seal differs between type A and type B, based on the shape of the dust deflector portion of the rear drive pinion companion flange sub-assembly rear.
| *a | Oil Seal Depth |
Using SST and a hammer, tap in a new rear differential carrier oil seal.
0.05 to 0.95 mm (0.00197 to 0.0374 in.)
1.55 to 2.45 mm (0.0611 to 0.0964 in.)
Apply MP grease to the lip of the rear differential carrier oil seal.
41204 12.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR
Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.
Before using SST (center bolt), apply hypoid gear oil to its threads and tip.
13.INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
Apply hypoid gear oil LSD to the drive pinion threads and nut seat face.
| *a | Turn |
| *b | Hold |
Using SST, hold the rear drive pinion companion flange sub-assembly in place, and install a new rear drive pinion companion flange nut.
or less
Using a torque wrench, measure the preload.
| Item | Specified Condition |
|---|---|
| New bearing | 1.04 to 1.69 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf) |
| Reused bearing | 0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf) |
If the result is not as specified, adjust the preload.
41204G 14.STAKE REAR DRIVE PINION COMPANION FLANGE NUT
Using a chisel and hammer, stake the rear drive pinion companion flange nut.
37110 15.INSTALL PROPELLER SHAFT ASSEMBLY
16.ADD DIFFERENTIAL OIL