88460 1.INSTALL COOLER CONDENSER ASSEMBLY
Install the cooler condenser assembly with the 2 bolts as shown in the illustration.
88716B 2.CONNECT COOLER REFRIGERANT LIQUID PIPE B
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.
ND-OIL 8 or equivalent
Install the O-ring on the cooler refrigerant liquid pipe B.
Connect the cooler refrigerant liquid pipe B on the cooler condenser assembly with the nut.
When tightening the nut, do not allow any tools to contact the pipe.
When tightening the nut, hold a part of the pipe near the connector.
88717 3.CONNECT NO. 1 COOLER REFRIGERANT SUCTION PIPE
Remove the attached vinyl tape from the pipe and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the pipe joint.
ND-OIL 8 or equivalent
Install the O-ring on the No. 1 cooler refrigerant suction pipe.
Connect the No. 1 cooler refrigerant suction pipe A on the cooler condenser assembly with the nut.
When tightening the nut, do not allow any tools to contact the pipe.
When tightening the nut, hold a part of the pipe near the connector.
88712 4.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE
Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.
ND-OIL 8 or equivalent
Install the O-ring on the No. 1 cooler refrigerant suction hose.
Connect the No. 1 cooler refrigerant suction hose on the cooler condenser assembly with the nut.
When tightening the nut, do not allow any tools to contact the pipe.
When tightening the nut, hold a part of the pipe near the connector.
88711 5.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE
Remove the attached vinyl tape from the hose and the connecting part of the cooler condenser assembly.
Sufficiently apply compressor oil to a new O-ring and the fitting surface of the hose joint.
ND-OIL 8 or equivalent
Install the O-ring on the No. 1 cooler refrigerant discharge hose.
Connect the No. 1 cooler refrigerant discharge hose on the cooler condenser assembly with the bolt.
When tightening the bolt, do not allow any tools to contact the pipe.
When tightening the bolt, hold a part of the pipe near the connector.
53205 6.INSTALL UPPER RADIATOR SUPPORT SUB-ASSEMBLY
Install the upper radiator support sub-assembly with the 6 bolts.
Attach the 3 clamps.
53510 7.INSTALL HOOD LOCK ASSEMBLY
Install the hood lock assembly with the 2 bolts.
53217A 8.INSTALL HOOD LOCK SUPPORT BRACE
Install the hood lock support brace with the 2 bolts.
86510 9.INSTALL HIGH PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>INSTALLATION
86520 10.INSTALL LOW PITCHED HORN ASSEMBLY
Click hereVehicle Exterior>HORN>HORN>INSTALLATION
16400 11.INSTALL RADIATOR ASSEMBLY
52119A 12.INSTALL FRONT BUMPER COVER
for Standard:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Standard)>INSTALLATION
for Step Type:
Click hereVehicle Exterior>EXTERIOR PANELS / TRIM>FRONT BUMPER (for Step Type)>INSTALLATION
53111 13.INSTALL RADIATOR GRILLE
14.CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
15.WARM UP ENGINE
16.CHECK FOR REFRIGERANT GAS LEAK