Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › STEERING PAD › 2014.08–2021.07
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0137998 STEERING PAD N

SUPPLEMENTAL RESTRAINT SYSTEMS  STEERING PAD  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Never dispose of a steering pad with an undeployed airbag.

·

The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.

·

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool).Perform the operation in a place away from electrical noise.

·

When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the steering pad.

·

The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad with a deployed airbag.

·

Do not apply water etc. to a steering pad with a deployed airbag.

·

Always wash your hands with water after completing the operation.



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the steering pad, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the Service Dept. of the distributor.


Hide 45130 2.DISPOSE OF STEERING PAD (WHEN INSTALLED IN VEHICLE)

NOTICE:
·

When disposing of the steering pad, use an unneeded vehicle to deploy the airbag.

·

Be sure to observe the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool).


i.
C110372N03
0.958,1.542 0.885,0.979 0.885,0.979 0.688,0.979 false 0.417,0.906 0.875,1.104 0.458,0.198 10 false SST

Connect SST to the battery.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.


ii.
C110475N10
1.167,0.938 1.094,0.385 1.094,0.385 0.896,0.385 false 0.615,0.313 1.073,0.51 0.458,0.198 10 SST

Check the function of SST.

Press SST activation switch, and check that the LED of SST activation switch comes on.

CAUTION:
·

Do not connect SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST malfunction is possible, so replace SST with a new one.




iii.

Disconnect SST from the battery.




c.

Remove the lower instrument panel finish panel assembly.

Click hereVehicle Interior>INTERIOR PANELS / TRIM>INSTRUMENT PANEL SAFETY PAD>REMOVAL


d.

Remove the lower steering column cover.

Click hereVehicle Exterior>WIPER / WASHER>WIPER SWITCH>REMOVAL


e.

Disconnect the cable from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



f.

Disconnect the airbag connector from the spiral cable sub-assembly.

i.
E298618C01
1.26,1.802 0.854,1.802 0.854,1.802 0.771,1.344 true 1.333,1.688 1.646,1.885 0.313,0.198 10 false *1
*1 Slider


Slide the slider to release the lock, and then disconnect the connector.



g.
B234315N01
0.823,1.344 0.823,1.042 true 0.448,1.052 1.385,1.052 1.385,1.052 1.385,1.344 true 0.135,0.948 0.594,1.146 0.458,0.198 10 false SST

Install SST.

CAUTION:

Check that there is no looseness in the steering wheel assembly and steering pad.


i.

Connect SST connector to the spiral cable sub-assembly.

SST
09082-00700  09082-00780  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.



ii.
B340835C02
0.729,1.521 0.646,0.917 0.646,0.917 0.521,0.917 false 1.604,1.896 1.917,2.052 0.313,0.156 10 false *a 0.208,0.844 0.667,1.042 0.458,0.198 10 false SST
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


iii.

While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage SST wire harness.



iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.



h.

Deploy the airbag.

i.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


ii.

Press SST activation switch and deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the vehicle.


HINT:

The airbag is deployed as the LED of SST activation switch comes on.




i.

Remove the steering pad.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL

CAUTION:
·

The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad with a deployed airbag.

·

Do not apply water etc. to a steering pad assembly with a deployed airbag.

·

After removal, quickly seal the steering pad assembly in a plastic bag.

·

Always wash your hands with water after completing the operation.




Hide 45130 3.DISPOSE OF STEERING PAD (WHEN NOT INSTALLED IN VEHICLE)

CAUTION:

Be sure to follow the procedure detailed below when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N26
0.875,1.208 0.833,0.635 0.833,0.635 0.646,0.635 false 0.365,0.563 0.823,0.76 0.458,0.198 10 SST

Check the function of SST.

SST
09082-00700  

CAUTION:

When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool).


i.
C110372N03
0.958,1.542 0.885,0.979 0.885,0.979 0.688,0.979 false 0.417,0.906 0.875,1.104 0.458,0.198 10 false SST

Connect SST to the battery.

Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.


ii.
C110475N10
1.167,0.938 1.094,0.385 1.094,0.385 0.896,0.385 false 0.615,0.313 1.073,0.51 0.458,0.198 10 SST

Check the function of SST.

Press SST activation switch, and check that the LED of SST activation switch comes on.

CAUTION:
·

Do not connect SST connector to the airbag.

·

If the LED comes on when the activation switch is not being pressed, SST malfunction is possible, so replace SST with a new one.




iii.

Disconnect SST from the battery.



b.

Remove the steering pad.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>REMOVAL

CAUTION:
·

When removing the steering pad, wait at least 90 seconds after the ignition switch off and the cable is disconnected from the negative (-) battery terminal.

·

When storing the steering pad, keep the airbag deployment side facing upward.




c.
B104882C54
1.99,1.594 1.99,1.25 false 2.656,0.51 2.969,0.667 0.313,0.156 10 *a 1.917,1.625 2.229,1.781 0.313,0.156 10 *b
*a Wire Diameter
*b Stripped Wire Section


Using braided wire, tie down the steering pad to an unneeded tire.

Cross-sectional area of stripped wire:

1.25 mm2 (0.00192 in.2)


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the steering pad, it may snap when the airbag is deployed. Always use a wire for vehicle use with an area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire: Area = 3.14 x (Diameter)2 / 4


i.
B233020C01
0.458,1.333 0.771,1.49 0.313,0.156 10 false *a 1.104,1.729 1.417,1.885 0.313,0.156 10 false *b
*a L = 35.0 mm (1.3780 in.)
*b M = 6.0 mm (0.2362 in.)


Install 2 bolts with washers to the steering pad.

Bolt:

L: 35.0 mm (1.3780 in.)

M: 6.0 mm (0.2362 in.)

Pitch: 1.0 mm (0.0393 in.)


NOTICE:
·

Tighten the bolts by hand until they become difficult to turn.

·

Do not tighten the bolts excessively.




ii.
B233021N01
2.385,1.323 2.385,1.667 true 2.906,1.333 1.688,1.333 true 2.969,1.24 3.333,1.51 0.365,0.271 10 false SST

After connecting SST to each other, connect them to the steering pad.

SST
09082-00802  (09082-10801, 09082-40800)


iii.
B233022C01
0.823,3.219 1.229,4.229 true 1.844,0.625 2.281,0.229 true 1.208,4.25 1.521,4.448 0.313,0.198 10 false *b 2.323,0.135 2.635,0.333 0.313,0.198 10 false *a
*a 2 times or more


Wind 3 wires at least 2 times each around the bolts installed on the left and right sides of the steering pad.

CAUTION:
·

Tightly wind the wires around the bolts so that there is no slack.

·

Make sure that the wires are tight. If there is slack in the wires, the steering pad may break loose when the airbag is deployed.




iv.
B233023C01
2.146,0.323 2.604,0.167 false 2.656,0.063 3.021,0.323 0.365,0.26 10 false *a
*a Deployment Side


Face the airbag deployment side of the steering pad upward on top of an unneeded tire and wheel set. Separately tie the left and right sides of the steering pad to the wheel through the hub nut holes. Position the SST connector so that it hangs downward through the hub hole of the wheel.

CAUTION:
·

Make sure that the wire harnesses are tight. If there is slack in the wire harnesses, the steering pad may break loose when the airbag is deployed.

·

Always tie down the steering pad with the airbag deployment side facing upward.



NOTICE:

The tire and wheel may be damaged by the airbag deployment, so use an unneeded tire and wheel.




d.
B233024N01
2.458,0.24 2.719,0.24 2.719,0.24 3.167,0.781 false 2.135,0.146 2.427,0.323 0.292,0.177 10 false SST

Install SST.

CAUTION:

Place the disc wheel on level ground.


i.

Connect SST connector.

SST
09082-00700  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the disc wheel.



ii.
B233025C01
1.74,0.375 1.063,0.375 1.063,0.375 1.063,0.646 false 1.823,0.26 2.115,0.438 0.292,0.177 10 false SST 1.344,2.583 1.604,2.792 0.26,0.208 10 false *a
*a 10 m or more


Move SST at least 10 m (32.8 ft.) away from the steering pad tied down to the wheel.



e.
B233026C01
0.552,1.844 0.781,1.844 0.781,1.844 1,2.177 true 2.573,2.875 2.375,2.875 2.375,2.875 2.552,2.313 true 1.031,0.615 1.188,0.792 0.156,0.177 10 false Y 0.844,1.26 1,1.438 0.156,0.177 10 false Y 2.948,1.479 3.104,1.656 0.156,0.177 10 false X 2.635,2.76 2.969,3.021 0.333,0.26 10 false *1 0.344,1.75 0.677,2.01 0.333,0.26 10 false *1
*a Weight


Cover the steering pad (using a cardboard box).

i.

Cover the steering pad with a cardboard box.


ii.

Place weights on the cardboard box in 4 places totaling at least 190 N (19 kg, 42.7 lb).

Minimum cardboard box size:
Must exceed the following dimensions:

X

460 mm (1.51 ft.)

Y

650 mm (2.13 ft.)


NOTICE:
·

When dimension Y of the cardboard box exceeds the diameter of the wheel and tire to which the steering pad is tied, X should be the following size.

X = 460 mm (1.51 ft.) + width of tire

·

If a cardboard box smaller than the specified size is used, it may be broken by the shock from the airbag deployment.





f.

Cover the steering pad (using tires).

i.

Place at least 3 tires without wheels onto the wheel and tire to which the steering pad is tied.


ii.
B233027C01
1.542,0.26 1.823,0.51 0.281,0.25 10 false *a 2.708,0.698 2.979,0.927 0.271,0.229 10 false *b 0.521,1.75 0.813,1.969 0.292,0.219 10 false *c
*a Inner Diameter
*b Width
*c Tires (3 or more)


Place a wheel and tire on top.

Minimum tire size:

Must exceed the following dimensions

Width

185 mm (7.28 in.)

Inner diameter

360 mm (1.18 ft.)


CAUTION:

Do not use tires with wheels except for on the top and bottom.


NOTICE:
·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.

·

Do not place SST connector under the tire because it could be damaged.




iii.
C107322

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires results in the tires breaking loose when the airbag is deployed.




g.
E298619C01
1.583,0.177 1.115,0.177 1.115,0.177 1.115,0.365 false 1.333,2.521 0.865,2.521 0.865,2.521 0.865,2.708 false 0.094,0.104 0.406,0.302 0.313,0.198 10 false *A 0.146,2.26 0.458,2.458 0.313,0.198 10 false *B 1.271,1.979 1.583,2.177 0.313,0.198 10 false *a 1.271,4.292 1.583,4.49 0.313,0.198 10 false *a 1.646,0.083 2.104,0.281 0.458,0.198 10 false SST 1.396,2.427 1.854,2.625 0.458,0.198 10 false SST
*A Using a Cardboard Box
*B Using Tires
*a 10 m or more


Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the wheel which the steering pad is tied.


iii.

Press SST activation switch to deploy the airbag.

CAUTION:

When deploying the airbag, make sure that no one is near the tire.


HINT:

The airbag is deployed as the LED of SST activation switch comes on.




h.
B181592

Dispose of the steering pad.

CAUTION:
·

The steering pad becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

Use gloves and safety glasses when handling a steering pad with a deployed airbag.

·

Do not apply water to a steering pad with a deployed airbag.

·

Always wash your hands with water after completing the operation.



i.

Remove the steering pad from the disc wheel.


ii.

Place the steering pad in a plastic bag, tie it tightly and dispose of it according to local regulations.