Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0138019 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 43502C 1.REMOVE FRONT AXLE HUB SUB-ASSEMBLY LH

Hide 2.DISCONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.
C305658

Remove the bolt and disconnect the front speed sensor LH.


Hide 43401 3.REMOVE STEERING KNUCKLE SPINDLE SUB-ASSEMBLY

a.
C305659

Remove the 8 bolts, front axle hub dust seal, knuckle spindle oil retainer gasket and front disc brake dust cover.


b.
C305660

Using a brass bar and hammer, tap the knuckle spindle of the steering knuckle.


c.

Remove the knuckle spindle and knuckle spindle gasket.


Hide 4.REMOVE FRONT AXLE SHAFT ASSEMBLY

a.

Position one flat part of the outer shaft upward and remove the front axle shaft assembly.


Hide 45451 5.DISCONNECT STEERING RELAY ROD (for RHD)

a.

Remove the cotter pin and nut.


b.
C305663N01
2.042,1.125 2.417,1.292 2.417,1.292 2.854,1.292 false 2.917,1.229 3.281,1.427 0.365,0.198 10 false SST

Using SST, disconnect the steering relay rod from the steering knuckle arm.

SST
09611-22012  


Hide 45047 6.DISCONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Remove the cotter pin and nut.


b.
C305664N01
2.823,1.521 2.552,1.521 2.552,1.521 2.281,1.177 false 2.875,1.448 3.208,1.656 0.333,0.208 10 false SST

Using SST, disconnect the tie rod from the steering knuckle arm.

SST
09611-22012  


Hide 43241 7.REMOVE STEERING KNUCKLE OIL SEAL COVER

a.
C305665

Remove the 6 bolts and 2 steering knuckle oil seal covers.


Hide 43232 8.REMOVE STEERING KNUCKLE BEARING CAP

a.
C305666

Remove the 2 bolts from the bearing cap.


b.
C305667C01
2.26,1.74 2.438,1.74 2.438,1.74 2.708,1.406 true 2.146,0.479 2.292,0.479 2.292,0.479 2.656,0.927 true 2.094,1.646 2.406,1.802 0.313,0.156 10 false *a 1.813,0.385 2.167,0.604 0.354,0.219 10 false SST
*a Wooden plate


Using SST and wooden plate, remove the steering knuckle bearing cap and shim from the steering knuckle.

SST
09606-60020  


Hide 45611G 9.REMOVE NO. 1 STEERING KNUCKLE ARM

a.
C305668

Remove the 4 nuts from the No. 1 steering knuckle arm.


b.

Using a brass bar and hammer, tap on the heads of the 4 bolts to remove the 4 cone washers.


c.
C305669C01
2,0.438 2.292,0.438 2.292,0.438 2.542,0.729 true 2.333,1.625 2.531,1.625 2.531,1.625 2.74,1.177 true 1.813,0.344 2.125,0.5 0.313,0.156 10 false *a 2.031,1.542 2.49,1.74 0.458,0.198 10 false SST
*a Wooden plate


Using SST and wooden plate, remove the No. 1 steering knuckle arm from the steering knuckle.

SST
09606-60020  


d.

Remove the steering knuckle king pin dust or ring seal from the No.1 steering knuckle arm.


Hide 45612A 10.REMOVE NO. 2 STEERING KNUCKLE ARM

HINT:

Use the same procedure described for the No. 1 steering knuckle arm.


Hide 43204 11.REMOVE STEERING KNUCKLE OIL SEAL SUB-ASSEMBLY

a.

Remove the steering knuckle outer oil seal, steering knuckle inner oil seal and steering knuckle oil seal inner ring from the steering knuckle.


Hide 43212 12.REMOVE STEERING KNUCKLE LH

a.

Remove the steering knuckle from the front axle housing assembly.


b.
C305693C01
1.792,0.479 2.104,0.635 0.313,0.156 10 false *a 1.74,1.375 2.052,1.531 0.313,0.156 10 false *b
*a LH Upper side
*b LH Lower side


Remove 2 steering knuckle arm bearings from the steering knuckle.

HINT:

Mark the removed adjusting shim and bearings so as to enable reassembling them to their proper positions.



c.
C399805

Using an E12 "TORX" socket wrench, remove the 4 steering set stud bolts frome the steeing knuckle LH.


Hide 45611F 13.REMOVE STEERING KNUCKLE ARM BEARING

a.
C305694

Using a brass bar and hammer, remove the 2 bearing outer races.


Hide 43411D 14.REMOVE FRONT DRIVE SHAFT TYPE T OIL SEAL

a.
C305695N01
2.042,0.833 2.406,0.198 2.406,0.198 2.781,0.198 true 2.854,0.115 3.24,0.313 0.385,0.198 10 false SST

Using SST, remove the front drive shaft type T oil seal from the front axle housing assembly.

SST
09308-00010  


Hide 43211R 15.REMOVE STEERING KNUCKLE BUSHING

a.
C305696N01
1.896,1.354 2.188,1.354 false 1.615,1.292 2.021,1.469 0.406,0.177 10 false SST

Using SST, remove the steering knuckle bushing from the steering knuckle spindle.

SST
09612-65014  (09612-01010, 09612-01050)


b.

Remove the needle roller bearing from the steering knuckle spindle.


Hide 43405 16.REMOVE FRONT AXLE OUTER SHAFT SUB-ASSEMBLY

a.

Secure the front axle inner shaft LH in a vise using aluminum plates.


b.
C305697

Place a brass bar against the joint inner race and remove the front axle outer shaft assembly.

HINT:

When removing the outer shaft, the snap ring will be broken.