Home › Drivetrain › AXLE AND DIFFERENTIAL › STEERING KNUCKLE › 2014.08–2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0138019 STEERING KNUCKLE A

AXLE AND DIFFERENTIAL  STEERING KNUCKLE  INSTALLATION  


CAUTION / NOTICE / HINT

PROCEDURE

Hide 43405 1.INSTALL FRONT AXLE OUTER SHAFT SUB-ASSEMBLY

a.
C305698

Hold the front axle outer shaft in a vise and while compressing a new snap ring, install the front axle inner shaft to the front axle outer shaft.


b.

Make sure that the front axle inner shaft cannot be pulled out.


Hide 43211R 2.INSTALL STEERING KNUCKLE BUSHING

a.
C305699N01
2.583,0.719 2.958,0.719 false 2.99,0.646 3.365,0.844 0.375,0.198 10 false SST

Using SST and a press, install a new needle roller bearing and new steering knuckle bushing into the steering knuckle spindle.

SST
09618-60010  


Hide 43411D 3.INSTALL FRONT DRIVE SHAFT TYPE T OIL SEAL

a.
C305700N01
2.135,0.958 2.385,0.354 2.385,0.354 2.792,0.354 true 2.865,0.281 3.271,0.479 0.406,0.198 10 false SST

Using SST and a hammer, install a new front drive shaft type T oil seal into the front axle housing assembly.

SST
09618-60010  


b.

Coat the seal lip with MP grease.


Hide 45611F 4.INSTALL STEERING KNUCKLE ARM BEARING

a.
C305701N01
0.385,0.656 0.542,0.656 0.542,0.656 0.74,0.906 true 0.083,0.573 0.469,0.771 0.385,0.198 10 false SST

Using SST and a hammer, carefully install 2 new bearing outer races.

SST
09605-60010  


b.

Place MP grease in the palm of your hand.


c.

Pack grease into the steering knuckle arm bearing, continuing until the grease oozes out from the other side.


d.

Do the same around the bearing circumference.


Hide 43211A 5.INSTALL STEERING SET STUD BOLT

a.

Degrease and clean the steering knuckle LH bolt hole.


b.
C399805

Using an E12 "TORX" socket wrench, install the 4 steering set stud bolts to the steering knuckle LH.

Torque:
49 N*m (500 kgf*cm, 36 ft.*lbf)

NOTICE:
·

When replacing the steering set stud bolt, replace the installation nuts with the new nuts that are supplied.

·

Install the steering set stud bolts with the side coated with sealant on the steering LH side.

·
C435594C01
0,0 0,0 false
V100155

Steering Knuckle Installation Seat


After installing the steering set stud bolts, do not allow sealant on the steering knuckle installation seat.




Hide 43212 6.INSTALL STEERING KNUCKLE LH

a.

Place the 2 steering knuckle arm bearings in positions on the steering knuckle and front axle housing.


b.

Install the steering knuckle to the front axle housing assembly.


Hide 43204 7.INSTALL STEERING KNUCKLE OIL SEAL SUB-ASSEMBLY

a.

Install a new steering knuckle outer oil seal, new steering knuckle inner oil seal and new steering knuckle oil seal inner ring to the steering knuckle.


Hide 43232 8.TEMPORARILY INSTALL STEERING KNUCKLE BEARING CAP

C305702C01
2.135,1.542 2.448,1.542 2.448,1.542 2.677,0.969 true 2.167,1.865 2.531,1.865 2.531,1.865 2.698,1.417 true 1.99,1.771 2.302,1.927 0.313,0.156 10 false *a 1.823,1.458 2.198,1.667 0.375,0.208 10 false SST
*a Wooden Plate


a.

Using SST and wooden plate, support the upper bearing inner race.

SST
09606-60020  


b.

Install the steering knuckle bearing cap over the used No. 1 steering knuckle adjust shim.


c.

Using a hammer, install the bearing cap into the bearing inner race.


Hide 45611G 9.TEMPORARILY INSTALL NO. 1 STEERING KNUCKLE ARM

a.

Install a new steering knuckle king pin dust or ring seal to the No.1 steering knuckle arm.


b.
C307919C01
1.99,0.385 2.229,0.385 2.229,0.385 2.49,0.646 true 1.917,1.771 2.25,1.771 2.25,1.771 2.667,1.115 true 1.813,0.292 2.125,0.448 0.313,0.156 10 false *a 1.635,1.708 1.938,1.875 0.302,0.167 10 false SST
*a Wooden Plate


Using SST and wooden plate, support the lower bearing inner race.

SST
09606-60020  


c.

Using a hammer, install the No. 1 steering knuckle arm into the bearing inner race.


d.

Remove SST from the steering knuckle.


Hide 45612A 10.TEMPORARILY INSTALL NO. 2 STEERING KNUCKLE ARM

HINT:

Use the same procedure described for the No. 1 steering knuckle arm.


Hide 43232 11.INSTALL STEERING KNUCKLE BEARING CAP

a.

Install the steering knuckle bearing cap with the 2 bolts.

Torque:
96.1 N*m (980 kgf*cm, 71 ft.*lbf)


Hide 45611G 12.INSTALL NO. 1 STEERING KNUCKLE ARM

a.

Install the No. 1 steering knuckle arm with the 4 cone washers and 4 nuts.

Torque:
123 N*m (1254 kgf*cm, 91 ft.*lbf)


Hide 45612A 13.INSTALL NO. 2 STEERING KNUCKLE ARM

HINT:

Use the same procedure described for the No. 1 steering knuckle arm.


Hide 45611F 14.MEASURE BEARINGS PRELOAD

a.
C305704N01
1.802,1.177 2.26,1.375 0.458,0.198 10 false 90°

Using a spring tension gauge, measure the preload.

Preload (at starting):

25 to 44 N (3 to 4 kgf, 5.6 to 9.9 lbf)



Hide 45611F 15.ADJUST BEARINGS PRELOAD

a.

Remove the steering knuckle bearing cap and No. 1 steering knuckle adjust shim.


b.

Select the No. 1 steering knuckle adjust shim.

Adjusting Shim Thickness:
Thickness mm (in.)
0.1 (0.004)
0.2 (0.008)
0.5 (0.020)
1.0 (0.039)



c.

Install the steering knuckle bearing cap with the 2 bolts.

Torque:
96.1 N*m (980 kgf*cm, 71 ft.*lbf)


Hide 43241 16.INSTALL STEERING KNUCKLE OIL SEAL COVER

a.

Install the 2 steering knuckle oil seal covers to the steering knuckle with the 6 bolts.

Torque:
5.4 N*m (55 kgf*cm, 48 in.*lbf)


Hide 45047 17.CONNECT TIE ROD END SUB-ASSEMBLY LH

a.

Connect the tie rod end to the No. 1 steering knuckle arm with the nut.

Torque:
90.7 N*m (925 kgf*cm, 67 ft.*lbf)

NOTICE:

Tighten the nut up to an additional 60° if the holes for the cotter pin are not aligned.



b.

Install a new cotter pin.


Hide 18.INSTALL FRONT AXLE SHAFT ASSEMBLY

a.

Position one flat part of the outer shaft upward and install the front axle shaft assembly.


Hide 19.PACK STEERING KNUCKLE WITH GREASE

a.
C305705C01
0.448,1.26 1.24,1.26 true 0.24,1.156 0.552,1.313 0.313,0.156 10 false *a
*a Molybdenum Disulfide Lithium Base Grease, NLGI No. 2


Pack molybdenum disulfide lithium base grease, NLGI No. 2 into the steering knuckle to about 3 fourths of the steering knuckle.


Hide 43401 20.INSTALL STEERING KNUCKLE SPINDLE SUB-ASSEMBLY

a.

Place a new knuckle spindle gasket in position on the steering knuckle and install the knuckle spindle.


b.

Place the front disc brake dust cover, new front axle hub dust seal and a new knuckle spindle oil retainer gasket on the steering knuckle spindle.


c.

Install the 8 bolts.

Torque:
46.6 N*m (475 kgf*cm, 34 ft.*lbf)


Hide 21.CONNECT FRONT SPEED SENSOR LH (w/ ABS)

a.

Connect the front speed sensor LH to the steering knuckle with the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 43502C 22.INSTALL FRONT AXLE HUB SUB-ASSEMBLY LH

Hide 23.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT