The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.
The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.
DTC B1603/83, B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1603/83 | Front Satellite Sensor Bus RH Initialization Incomplete | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.
·
A front airbag sensor RH malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Front airbag sensor RH
·
Airbag sensor assembly |
| B1612/83 | Lost Communication with Front Airbag Sensor RH | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.
·
A front airbag sensor RH malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Front airbag sensor RH
·
Airbag sensor assembly |
| B1613/83 | Front Airbag Sensor RH Initialization Incomplete | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.
·
A front airbag sensor RH malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
Front airbag sensor RH
·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH.
| Proceed to |
|---|
| The connectors are properly connected |
| The connectors are not properly connected |
The connectors are properly connected
The connectors are not properly connected
Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH.
| *1 | Front Airbag Sensor RH |
| *2 | Airbag Sensor Assembly |
| *3 | Cowl Wire |
Check that the connectors (on the airbag sensor assembly side and front airbag sensor RH side) are not damaged.
| Proceed to |
|---|
| The connectors are not deformed or damaged |
| The connectors are deformed or damaged |
The connectors are not deformed or damaged
The connectors are deformed or damaged
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
| *1 | Front Airbag Sensor RH | *2 | Airbag Sensor Assembly |
| *3 | Cowl Wire | *4 | Connector C |
| *5 | Connector B | *6 | Service Wire |
| *a | Front view of wire harness connector (to Front Airbag Sensor RH) |
*b | Rear view of wire harness connector (to Airbag Sensor Assembly) |
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I52-2 (+SR) - Body ground | Ignition switch ON | Below 1 V |
| I52-1 (-SR) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.
Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I52-2 (+SR) - I52-1 (-SR) | Always | Below 1 Ω |
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I52-2 (+SR) - I52-1 (-SR) | Always | 1 MΩ or higher |
| I52-2 (+SR) - Body ground | Always | 1 MΩ or higher |
| I52-1 (-SR) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Airbag Sensor LH |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the airbag sensor assembly.
Interchange the front airbag sensor RH with LH and connect the connectors to them.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in memory.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B1603/83, B1612/83 or B1613/83 is output | A |
| DTC B1608/84, B1617/84 or B1618/84 is output | B |
| DTC B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 are not output | C |
Codes other than DTC B1603/83, DTC B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Return the front airbag sensor LH and RH to their original positions and connect the connectors to them.
A
B
C