The front passenger side squib circuit consists of the airbag sensor assembly and instrument panel passenger airbag assembly.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib circuit.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B1805/52 | Short in Front Passenger Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a line short circuit signal 5 times in the front passenger side squib circuit during the primary check.
·
An instrument panel passenger airbag assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
No. 3 instrument panel wire
·
Instrument panel passenger airbag assembly
·
Airbag sensor assembly |
| B1806/52 | Open in Front Passenger Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects an open circuit signal in the front passenger side squib circuit for 2 seconds.
·
An instrument panel passenger airbag assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
No. 3 instrument panel wire
·
Instrument panel passenger airbag assembly
·
Airbag sensor assembly |
| B1807/52 | Short to GND in Front Passenger Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to ground signal in the front passenger side squib circuit for 0.5 seconds.
·
An instrument panel passenger airbag assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
No. 3 instrument panel wire
·
Instrument panel passenger airbag assembly
·
Airbag sensor assembly |
| B1808/52 | Short to B+ in Front Passenger Side Squib Circuit | One of the following conditions is met:
·
The airbag sensor assembly detects a short circuit to B+ signal in the front passenger side squib circuit for 0.5 seconds.
·
An instrument panel passenger airbag assembly malfunction.
·
An airbag sensor assembly malfunction. |
·
Cowl wire
·
No. 3 instrument panel wire
·
Instrument panel passenger airbag assembly
·
Airbag sensor assembly |
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
To perform the simulation method, enter check mode (signal check) with the GTS (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).
| *1 | Front Passenger Side Squib |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *4 | SST |
| *a | Front view of wire harness connector (to Instrument Panel Passenger Airbag Assembly) |
| *b | Color: Orange |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connector from the instrument panel passenger airbag assembly.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).
Never connect the tester to the instrument panel passenger airbag assembly for measurement, as this may lead to a serious injury due to airbag deployment.
Do not forcibly insert SST into the terminals of the connector when connecting SST.
Insert SST straight into the terminals of the connector.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output |
| DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output |
Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output
Disconnect the connector from the airbag sensor assembly.
| *1 | Front Passenger Side Squib |
| *2 | Airbag Sensor Assembly |
Check that the connectors (on the airbag sensor assembly side and instrument panel passenger airbag assembly side) are not damaged.
The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Passenger Side Squib |
| *2 | Airbag Sensor Assembly |
| *3 | Connector E |
| *a | Front view of wire harness connector (to Instrument Panel Passenger Airbag Assembly) |
| *b | Color: Orange |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| N1-1 (P+) - Body ground | Ignition switch ON | Below 1 V |
| N1-2 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-1 (P+) - N1-2 (P-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-1 (P+) - N1-2 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| N1-1 (P+) - Body ground | Always | 1 MΩ or higher |
| N1-2 (P-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *1 | Front Passenger Side Squib |
| *2 | Airbag Sensor Assembly |
Connect the connectors to the instrument panel passenger airbag assembly and airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR
| Proceed to |
|---|
| DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output |
| DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output |
Codes other than DTC B1805/52, B1806/52, B1807/52 and B1808/52 may be output at this time, but they are not related to this check.
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is not output
DTC B1805/52, B1806/52, B1807/52 or B1808/52 is output
| *1 | Instrument Panel Passenger Airbag Assembly |
| *2 | Airbag Sensor Assembly |
| *3 | No. 3 Instrument Panel Wire |
| *4 | Cowl Wire |
| *5 | Connector C |
| *a | Front view of wire harness connector (to No. 3 Instrument Panel Wire) |
Disconnect the cowl wire connector from the No. 3 instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| IN1-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
| IN1-1 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IN1-2 (P+) - IN1-1 (P-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IN1-2 (P+) - IN1-1 (P-) | Always | 1 MΩ or higher |
Restore the released activation prevention mechanism of connector B to its original condition.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| IN1-2 (P+) - Body ground | Always | 1 MΩ or higher |
| IN1-1 (P-) - Body ground | Always | 1 MΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG