Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2014.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1662/45  Indicator Light Circuit Malfunction  


DESCRIPTION

The indicator light circuit consists of the airbag sensor assembly and combination meter assembly.

When the airbag sensor assembly detects a malfunction in the SRS airbag system, the SRS warning light comes on to inform the driver. It also comes on when the source voltage drops, and automatically goes off in approximately 10 seconds after the source voltage returns to normal (DTC is not stored).

The SRS warning light comes on for 6 seconds after the ignition switch is turned to ON and goes off if the system is normal.

When an open circuit is detected, such as when the connector between the combination meter assembly and airbag sensor assembly is disconnected, the SRS warning light remains on even when approximately 6 seconds elapsed after the ignition switch is turned to ON.

DTC B1662/45 is stored when a malfunction is detected in the indicator light circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1662/45 Indicator Light Circuit Malfunction When one of the following conditions is met:
·

The airbag sensor assembly receives an open circuit signal, short to ground signal, or short circuit to ground signal or short circuit to B+ signal in the indicator light circuit for 2 seconds.

·

A combination meter assembly malfunction.

·

An airbag sensor assembly malfunction.


·

Combination meter assembly (SRS warning light)

·

Airbag sensor assembly

·

Instrument panel wire



WIRING DIAGRAM

C315265E01
0.219,3.271 1.104,3.927 0.885,0.656 10 false from Battery 5.51,5.906 7.135,6.469 1.625,0.563 10 false Airbag Sensor Assembly 2.792,5.719 4.781,6.302 1.99,0.583 10 false Combination Meter Assembly 5.51,5.729 5.969,5.927 0.458,0.198 10 false I51 4.125,2.26 4.583,2.458 0.458,0.198 10 false L26 2.802,2.667 3.26,2.865 0.458,0.198 10 false L25 2.802,3.26 3.26,3.458 0.458,0.198 10 false L25 2.802,4.25 3.26,4.448 0.458,0.198 10 false L25 3.146,2.677 3.604,2.875 0.458,0.198 10 false B 3.167,3.271 3.625,3.469 0.458,0.198 10 false B 3.146,4.271 3.604,4.469 0.458,0.198 10 false ES 3.823,2.25 4.281,2.448 0.458,0.198 10 false A/B 6.156,2.271 6.615,2.469 0.458,0.198 10 false LA 6.146,3.656 6.604,3.854 0.458,0.198 10 false E1 6.146,4.292 6.604,4.49 0.458,0.198 10 false E2 5.875,4.177 6.333,4.375 0.458,0.198 10 false 26 5.865,3.583 6.323,3.781 0.458,0.198 10 false 25 5.906,2.188 6.365,2.385 0.458,0.198 10 false 11 5.896,0.771 6.354,0.969 0.458,0.198 10 false 21 6.135,0.896 6.594,1.094 0.458,0.198 10 false IG2 2.115,1.042 2.573,1.24 0.458,0.198 10 false IGN 2.115,2.823 2.573,3.021 0.458,0.198 10 false MET 1.875,3.438 2.75,3.792 0.875,0.354 10 false DOME NO.1 0.188,0.813 0.958,1.417 0.771,0.604 10 false from Ignition Switch 4.146,2.073 4.594,2.302 0.448,0.229 10 false 19 2.813,2.469 3.26,2.698 0.448,0.229 10 false 28 2.813,3.083 3.26,3.313 0.448,0.229 10 false 26 2.854,4.063 3.302,4.292 0.448,0.229 10 false 15

CAUTION / NOTICE / HINT

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

1.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK CONNECTORS

NG

CHECK AND REPLACE BATTERY OR CHARGING SYSTEM

2.CHECK CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

3.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.
C212445C02
0.427,1.188 0.844,1.427 0.417,0.24 1.063,1.896 1.656,1.552 true 2.292,1.885 1.75,1.552 true 2.688,1.854 2.146,1.521 true 0.25,0.135 0.563,0.292 0.313,0.156 10 false *a 0.51,1.208 0.823,1.365 0.313,0.156 10 false I51 0.938,1.927 1.25,2.083 0.313,0.156 10 false E2 2.74,1.865 3.135,2.021 0.396,0.156 10 false IG2 2.271,1.927 2.667,2.083 0.396,0.156 10 false E1
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Disconnect the connector from the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-25 (IE1) - Body ground Always Below 1 Ω
I51-26 (IE2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.
C212427C03
1.542,0.677 1.906,0.948 0.365,0.271 0.667,1.917 0.833,1.917 0.833,1.917 1.042,1.667 false 2.833,1.917 2.667,1.917 2.667,1.917 2.417,1.635 false 2.75,2.083 2.583,2.083 2.583,2.083 2.198,1.677 false 0.125,0.208 0.438,0.365 0.313,0.156 10 false *a 1.594,0.729 1.906,0.885 0.313,0.156 10 false L25 0.438,1.833 0.75,2.031 0.313,0.198 10 false ES 2.896,1.833 3.208,2.031 0.313,0.198 10 false B 2.792,2 3.083,2.177 0.292,0.177 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the combination meter assembly.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON.


f.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
L25-28 (B) - Body ground Ignition switch ON 11 to 14 V
L25-26 (B) - Body ground Always 11 to 14 V



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-15 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.

Turn the ignition switch off.


C212446C03
0.448,3.729 0.896,3.958 0.448,0.229 0.458,1.177 0.906,1.406 0.448,0.229 0.948,4.427 1.844,4.281 true 2.26,1.396 2.531,1.521 true 0.365,0.26 0.677,0.417 0.313,0.156 10 false *a 0.469,3.104 0.781,3.26 0.313,0.156 10 false *b 2.625,1.448 2.938,1.604 0.313,0.156 10 false LA 0.688,4.354 1.271,4.51 0.583,0.156 10 false A/B 0.531,3.771 1.115,3.927 0.583,0.156 10 false L26 0.521,1.219 1.104,1.375 0.583,0.156 10 false I51
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L51-11 (LA) - L26-19 (A/B) Always Below 1 Ω
L51-11 (LA) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK SRS WARNING LIGHT (SHORT TO GROUND)
a.

Connect the connector to the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Check the SRS warning light condition.

OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.


HINT:

The primary check period is approximately 6 seconds after the ignition switch is turned to ON.



Result:
Proceed to
OK
NG



OK

NG