Home › Drivetrain › HF1A (TRANSFER / 4WD / AWD) › TRANSFER SYSTEM
RM25T0E _52 Drivetrain _029904 HF1A TRANSFER / 4WD / AWD _0138375 TRANSFER SYSTEM G

HF1A TRANSFER / 4WD / AWD  TRANSFER SYSTEM  INSPECTION  


PROCEDURE

Hide 1. TRANSFER SYSTEM

NOTICE:
·

w/ Dual Mode Automatic Locking Hub (AUTO Position):

To shift from H2 to H4, stop the vehicle and move the transfer shift lever.

·

To shift from H4 to L4, stop the vehicle or reduce the vehicle speed to less than 8 km/h (5 mph). Then, release the accelerator pedal, depress the clutch pedal and move the transfer shift lever.

·

To shift from L4 to H4, depress the clutch pedal and move the transfer shift lever.



Hide 2.INSPECT INDICATOR LIGHT

a.

4WD Indicator Light:

i.

Start the engine.


ii.

Move the transfer shift lever from the H2 position to the H4, L4 or N position.


iii.

Check that the 4WD indicator light illuminates.

OK:

4WD indicator light comes on


If the result is not as specified, inspect the No. 1 transfer indicator switch (4WD position) and four wheel drive control ECU (w/ Differential Lock).

If the system is normal, there may be a malfunction in the combination meter (Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>PROBLEM SYMPTOMS TABLE).



Hide 89533A 3.INSPECT NO. 2 4 WHEEL DRIVE CONTROL ECU (w/ Differential Lock)

a.

Inspect the No. 2 4 wheel drive control ECU (power supply).

i.
C312231C03
2.688,1.75 2.875,1.75 2.875,1.75 2.875,1.302 true 1.625,0.344 1.448,0.344 1.448,0.344 1.448,1.125 true 2.49,1.667 2.802,1.865 0.313,0.198 10 false IG 1.688,0.25 2,0.448 0.313,0.198 10 false GND 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a
*a Component with harness connected
(No. 2 4 Wheel Drive Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
8 (IG) - Body ground Ignition switch ON 11 to 14 V


If the result is not as specified, inspect the harness, fuse or connector.

If the harness or connector is malfunctioning, repair or replace the harness or connector.

If the harness or connector is normal, replace the No. 2 4 wheel drive control ECU (Click here Drivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER INDICATOR SWITCH>INSPECTION).


ii.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
13 (GND) - Body ground Always Below 1 Ω


If the result is not as specified, repair or replace the harness or connector.



b.

Inspect the No. 2 4 wheel drive control ECU (No. 1 transfer indicator switch).

i.
C312231C05
1.167,1.854 0.958,1.854 0.958,1.854 0.958,1.313 true 0.083,0.083 0.396,0.281 0.313,0.198 10 false *a 1.26,1.76 1.75,2.01 0.49,0.25 10 false 4WD
*a Component with harness connected
(No. 2 4 Wheel Drive Control ECU)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
15 (4WD) - Body ground Ignition switch ON
Transfer position H2
8 to 14 V
Ignition switch ON
Transfer position H4
8 to 14 V
Ignition switch ON
Transfer position N or L4
Below 1 V


If the result is not as specified, check the power supply.

If the power supply is normal, inspect the No. 1 transfer indicator switch (Click hereDrivetrain>HF1A (TRANSFER / 4WD / AWD)>TRANSFER INDICATOR SWITCH>INSPECTION).