Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT PROPELLER SHAFT ASSEMBLY
RM25T0E _52 Drivetrain _029905 DRIVE SHAFT / PROPELLER SHAFT _0138401 FRONT PROPELLER SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT PROPELLER SHAFT ASSEMBLY  REASSEMBLY  


CAUTION / NOTICE / HINT

NOTICE:
·

When using a vise, place aluminum plates between the part and vise.

·

When using a vise, do not overtighten it.



PROCEDURE

Hide 1.INSTALL SPIDER BEARING

HINT:

Use the same procedure for both spiders.


a.
C258225

Apply MP grease to a new spider and new spider bearing.

NOTICE:

Do not apply too much MP grease.



b.

Install the spider to the propeller shaft.


c.
C307743C01
0.552,0.229 1.042,0.427 true 1.375,1.427 1.688,1.625 0.313,0.198 10 false *a 2.979,0.5 3.292,0.698 0.313,0.198 10 false *b 0.24,0.156 0.698,0.354 0.458,0.198 10 false SST
*a Turn
*b Hold


Using SST, install 2 of the spider bearings to the spider.

SST
09332-25010  


d.

Using SST, adjust both spider bearings so that the front propeller shaft joint spider bearing snap ring grooves are at maximum and equal in width.

SST
09332-25010  


e.
C307723

Install 2 new front propeller shaft joint spider bearing snap rings of equal thickness which will allow no axial play.

HINT:

Do not reuse the front propeller shaft joint spider bearing snap rings.


Standard Snap Ring Thickness
Color Mark Thickness
- J 2.18 to 2.20 mm
(0.0859 to 0.0866 in.)
- K 2.20 to 2.22 mm
(0.0867 to 0.0874 in.)
- F 2.22 to 2.24 mm
(0.0875 to 0.0881 in.)
- G 2.24 to 2.26 mm
(0.0882 to 0.0889 in.)
- H 2.26 to 2.28 mm
(0.0890 to 0.0897 in.)
- 1 2.28 to 2.30 mm
(0.0898 to 0.0905 in.)
- 2 2.30 to 2.32 mm
(0.0906 to 0.0913 in.)
- - 2.32 to 2.34 mm
(0.0914 to 0.0921 in.)
Brown - 2.34 to 2.36 mm
(0.0922 to 0.0929 in.)
Blue - 2.36 to 2.38 mm
(0.0930 to 0.0937 in.)
- 6 2.38 to 2.40 mm
(0.0938 to 0.0944 in.)
- 7 2.40 to 2.42 mm
(0.0945 to 0.0952 in.)
- 8 2.42 to 2.44 mm
(0.0953 to 0.0960 in.)
-
C262545

2.44 to 2.46 mm
(0.0961 to 0.0968 in.)
- 10 2.46 to 2.48 mm
(0.0969 to 0.0976 in.)
- A 2.48 to 2.50 mm
(0.0977 to 0.0984 in.)
- B 2.50 to 2.52 mm
(0.0985 to 0.0992 in.)
- C 2.52 to 2.54 mm
(0.0993 to 0.0999 in.)
- D 2.54 to 2.56 mm
(0.1000 to 0.1007 in.)
- E 2.56 to 2.58 mm
(0.1008 to 0.1015 in.)

NOTICE:
·

Use a new front propeller shaft joint spider bearing snap ring.

·

Use front propeller shaft joint spider bearing snap ring with as close to the same thickness as possible on both ends.




f.
C258227C01
2.323,0.677 1.792,0.49 1.792,0.49 1.521,0.49 false 1.302,0.396 1.49,0.594 0.188,0.198 10 *a
*a Hammering Point


Using a hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and front propeller shaft joint spider bearing snap ring.

HINT:

Install the spider bearing on the sleeve side using the procedure described above.



g.

Align the matchmarks on the flange yoke and sleeve yoke.


h.
C307744C01
1.167,1 1.167,0.417 1.167,0.417 1.25,0.417 true 2.5,1.333 2.865,1.323 true 1.323,1.573 1.635,1.771 0.313,0.198 10 false *a 0.979,0.125 1.292,0.323 0.313,0.198 10 false *b 1.292,0.333 1.75,0.531 0.458,0.198 10 false SST 2.948,1.25 3.167,1.469 0.219,0.219 10 false A
*a Turn
*b Hold


Using SST, install the 2 spider bearings to the spider.

SST
09332-25010  

HINT:

Before installing SST, sufficiently raise the part labeled A. If the part labeled A is too low, it may be difficult to install SST.



i.

Using SST, adjust both spider bearings so that the front propeller shaft joint spider bearing snap ring grooves are at maximum and equal in width.

SST
09332-25010  


j.

Install 2 new front propeller shaft joint spider bearing snap rings of equal thickness which will allow 0 mm (0 in.) of axial play.

HINT:

Do not reuse the front propeller shaft joint spider bearing snap rings.


Standard Snap Ring Thickness
Color Mark Thickness
- J 2.18 to 2.20 mm
(0.0859 to 0.0866 in.)
- K 2.20 to 2.22 mm
(0.0867 to 0.0874 in.)
- F 2.22 to 2.24 mm
(0.0875 to 0.0881 in.)
- G 2.24 to 2.26 mm
(0.0882 to 0.0889 in.)
- H 2.26 to 2.28 mm
(0.0890 to 0.0897 in.)
- 1 2.28 to 2.30 mm
(0.0898 to 0.0905 in.)
- 2 2.30 to 2.32 mm
(0.0906 to 0.0913 in.)
- - 2.32 to 2.34 mm
(0.0914 to 0.0921 in.)
Brown - 2.34 to 2.36 mm
(0.0922 to 0.0929 in.)
Blue - 2.36 to 2.38 mm
(0.0930 to 0.0937 in.)
- 6 2.38 to 2.40 mm
(0.0938 to 0.0944 in.)
- 7 2.40 to 2.42 mm
(0.0945 to 0.0952 in.)
- 8 2.42 to 2.44 mm
(0.0953 to 0.0960 in.)
-
C262545

2.44 to 2.46 mm
(0.0961 to 0.0968 in.)
- 10 2.46 to 2.48 mm
(0.0969 to 0.0976 in.)
- A 2.48 to 2.50 mm
(0.0977 to 0.0984 in.)
- B 2.50 to 2.52 mm
(0.0985 to 0.0992 in.)
- C 2.52 to 2.54 mm
(0.0993 to 0.0999 in.)
- D 2.54 to 2.56 mm
(0.1000 to 0.1007 in.)
- E 2.56 to 2.58 mm
(0.1008 to 0.1015 in.)

NOTICE:
·

Use a new front propeller shaft joint spider bearing snap ring.

·

Use front propeller shaft joint spider bearing snap rings with as close to the same thickness as possible on both ends.




k.
C258229C01
1.646,2.031 1.896,2.031 1.896,2.031 2.344,1.792 false 1.458,1.938 1.667,2.125 0.208,0.188 10 *a
*a Hammering Point


Using a plastic-faced hammer, tap the flange yoke until there is no clearance between the spider bearing outer race and front propeller shaft joint spider bearing snap ring.

HINT:

Install the spider bearing on the sleeve side using the procedure described above.



Hide 2.INSPECT PROPELLER SHAFT GREASE FITTING DIRECTION

HINT:
·

When replacing a spider bearing, be sure that the grease fitting hole is facing the direction shown in the illustration.

·

Fill the grease fittings with MP grease.



C307724C01
0.948,1.656 0.781,1.656 0.781,1.656 0.781,0.906 true 1.063,1.396 0.896,1.396 0.896,1.396 0.896,0.896 true 4.208,1.635 4.042,1.635 4.042,1.635 4.042,0.885 true 5.208,1.24 5.521,1.438 0.313,0.198 10 false *a 5.083,0.802 5.396,1 0.313,0.198 10 false *b 5.135,0.385 5.448,0.583 0.313,0.198 10 false *c 4.229,1.552 4.542,1.708 0.313,0.156 10 false *c 0.99,1.573 1.313,1.74 0.323,0.167 10 false *a 1.115,1.323 1.427,1.521 0.313,0.198 10 false *b 2.677,0.24 2.99,0.438 0.313,0.198 10 false *d
*a Grease Fitting No. 1 *b Grease Fitting No. 2
*c Grease Fitting No. 3 *d Rear Side