Home › Engine / Hybrid System › 1VD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › 2016.08–2022.09
RM25T0E _51 Engine / Hybrid System _029760 1VD-FTV ENGINE CONTROL _0282525 ECD SYSTEM(w/ DPF) C

1VD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and sets the DTC.

HINT:

The normal conditions are as shown in the table below. The signals can be read using the GTS.

Signals Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0504 Brake Switch "A" / "B" Correlation Conditions (a), (b) and (c) continue for 0.5 seconds or more
(1 trip detection logic):
(a) Ignition switch ON
(b) Brake pedal released
(c) STP signal OFF when ST1- signal OFF
·

Short in stop light switch signal circuit

·

STOP fuse

·

IGN fuse

·

Stop light switch assembly

·

ECM


- DTC stored

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P0504 Depress and release brake pedal with engine switch on (IG)

WIRING DIAGRAM

A222283E05
0.573,0.885 1.865,1.052 1.292,0.167 10 false from Ignition Switch 1.01,1.875 1.896,2.083 0.885,0.208 10 false from Battery 2.448,0.729 2.76,0.885 0.313,0.156 10 false IGN 4.219,1.802 4.354,1.958 0.135,0.156 10 false 1 5.896,2.948 6.219,3.104 0.323,0.156 10 false A29 5.896,3.104 6.281,3.26 0.385,0.156 10 false ECM 3.094,1.802 3.229,1.958 0.135,0.156 10 false 2 3.052,0.792 3.188,0.948 0.135,0.156 10 false 4 5.313,0.813 5.51,0.969 0.198,0.156 10 false 35 5.313,1.802 5.51,1.958 0.198,0.156 10 false 13 5.594,0.813 5.938,0.969 0.344,0.156 10 false ST1- 5.594,1.802 5.938,1.958 0.344,0.156 10 false STP 4.208,0.781 4.344,0.938 0.135,0.156 10 false 3 4.656,1.729 5.063,1.885 0.406,0.156 10 false STOP 2.385,1.729 2.885,1.885 0.5,0.156 10 false STOP 3.135,2.24 3.458,2.385 0.323,0.146 10 false I19 3.135,2.396 4.271,2.583 1.135,0.188 10 false Stop Light Switch

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.

·

STP signal conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the ignition switch to ON.

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.

(e)

Check the STP signal when the brake pedal is depressed and released.




Brake Pedal Operation Specified Condition
Depressed STP signal ON
Released STP signal OFF

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.
A148738C18
1.5,0.813 1.958,1.094 0.458,0.281 0.188,0.177 0.458,0.365 0.271,0.188 10 false *a 1.604,0.875 1.875,1.021 0.271,0.146 10 false I19
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
I19-2 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

2.CHECK HARNESS AND CONNECTOR (TERMINAL VOLTAGE)
a.
A148738C18
1.5,0.813 1.958,1.094 0.458,0.281 0.188,0.177 0.458,0.365 0.271,0.188 10 false *a 1.604,0.875 1.875,1.021 0.271,0.146 10 false I19
*a Front view of wire harness connector
(to Stop Light Switch)


Disconnect the stop light switch connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
I19-4 - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.INSPECT STOP LIGHT SWITCH ASSEMBLY

NG

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION)
3.INSPECT STOP LIGHT SWITCH ASSEMBLY
a.
A115657C09
1.927,2.323 2.365,1.979 true 1.594,2.323 1.135,1.979 true 1.979,2.563 2.344,2.667 true 1.521,2.563 1.115,2.688 true 0.042,0.802 0.813,0.948 0.771,0.146 10 false Not Pushed 2.073,0.802 2.563,0.948 0.49,0.146 10 false Pushed 2.385,1.885 2.542,2.063 0.156,0.177 10 false 1 2.385,2.583 2.542,2.76 0.156,0.177 10 false 3 1.031,1.885 1.188,2.063 0.156,0.177 10 false 2 1,2.615 1.156,2.792 0.156,0.177 10 false 4 0.115,0.115 0.354,0.323 0.24,0.208 10 false *a
*a Component without harness connected
(Stop Light Switch)


Remove the stop light switch assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
1 - 2 Switch pin released Below 1 Ω
Switch pin pushed in 10 kΩ or higher
3 - 4 Switch pin released 10 kΩ or higher
Switch pin pushed in Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK ECM (STP AND ST1- VOLTAGE)

NG

REPLACE STOP LAMP SWITCH ASSEMBLY

4.CHECK ECM (STP AND ST1- VOLTAGE)
a.
A112585C11
1.531,2.552 2,2.885 0.469,0.333 1.781,3.365 2.313,4.354 true 1.771,3.667 1.344,4.354 true 2.448,0.448 2.708,0.646 0.26,0.198 10 false *b 0.708,0.427 0.948,0.656 0.24,0.229 10 false *a 0.333,2.167 0.563,2.448 0.229,0.281 10 false *c 2.313,4.396 2.885,4.594 0.573,0.198 10 false 13 (STP) 0.979,4.396 1.594,4.604 0.615,0.208 10 false 35 (ST1-) 1.656,2.635 1.948,2.813 0.292,0.177 10 false A29
*a Brake Pedal Depressed
*b Brake Pedal Released
*c Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Condition Specified Condition
A29-35 (ST1-) - Body ground Released 11 to 14 V
Depressed 0 to 3 V
A29-13 (STP) - Body ground Released 0 to 3 V
Depressed 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - IGNITION)
a.

Disconnect the stop light switch connector.


b.

Disconnect the ignition switch connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard resistance:
Tester Connection Condition Specified Condition
I19-4 - L21-6 (IG2) Always Below 1 Ω
I19-4 or L21-6 (IG2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG