Home › Brake › BRAKE SYSTEM (OTHER) › BRAKE MASTER CYLINDER (w/o VSC) › from 2016.08
RM25T0E _54 Brake _029916 BRAKE SYSTEM (OTHER) _0282727 BRAKE MASTER CYLINDER(w/o VSC) A

BRAKE SYSTEM (OTHER)  BRAKE MASTER CYLINDER(w/o VSC)  INSTALLATION  


PROCEDURE

Hide 1.INSPECT AND ADJUST BRAKE BOOSTER PUSH ROD

Hide 47201 2.INSTALL BRAKE MASTER CYLINDER SUB-ASSEMBLY

a.

for LHD:

i.

Install a new O-ring to the master cylinder.


ii.

Install a new brake master cylinder gasket to the master cylinder.


iii.

Install the master cylinder to the booster with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure foreign matter does not attach to the master cylinder piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



iv.
C313502

Connect the brake fluid level warning switch connector to the master cylinder.


v.

Connect the clutch reservoir tube to the master cylinder.


vi.
C313500C01
1.052,2.854 1.365,3.052 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 2 brake lines to the master cylinder.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)





b.

for RHD:

i.

Install a new O-ring to the master cylinder.


ii.

Install a new brake master cylinder gasket to the master cylinder.


iii.

Install the master cylinder and bracket to the booster with the 2 nuts.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)

NOTICE:

Make sure foreign matter does not attach to the master cylinder piston. If foreign matter attaches, clean it off with a cloth. Then apply lithium soap base glycol grease to the entire outer circumference contact surface area of the piston.



iv.
C314381

Install the 3-way to the bracket with the nut.

Torque:
12.5 N*m (127 kgf*cm, 9 ft.*lbf)


v.
C313501C01
1.094,2.688 1.406,2.885 0.313,0.198 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 5 brake lines to the brake master cylinder and 3-way.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




vi.

Connect the brake fluid level warning switch connector to the master cylinder.



Hide 4.BLEED CLUTCH LINE (for RHD)