Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › BRAKE ACTUATOR (w/o VSC) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0282729 BRAKE ACTUATOR(w/o VSC) A

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  BRAKE ACTUATOR(w/o VSC)  INSTALLATION  


PROCEDURE

Hide 44510 1.INSTALL BRAKE ACTUATOR ASSEMBLY WITH BRACKET

a.
C267646E01
0.791,1.275 0.914,1.422 0.123,0.147 10 A 1.934,1.733 2.057,1.880 0.123,0.147 10 B 2.461,1.256 2.584,1.403 0.123,0.147 10 C

Install the brake actuator with bracket with the 3 nuts.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)

NOTICE:
·

Be careful not to damage the brake tubes.

·

Tighten the 3 nuts uniformly in alphabetical order.




b.
C267644E02
2.548,0.881 2.706,1.029 0.158,0.148 10 *1 2.403,0.373 2.554,0.517 0.150,0.144 10 *2 1.347,1.791 1.497,1.944 0.150,0.154 10 *3 2.864,2.071 3.016,2.214 0.152,0.143 10 *4 2.642,3.031 2.793,3.174 0.152,0.143 10 *5 1.641,1.541 1.428,1.702 1.428,1.702 1.428,1.782 false 2.025,1.748 2.025,3.11 2.025,3.11 2.621,3.11 false 2.383,1.491 2.383,2.15 2.383,2.15 2.839,2.15 false 2.041,1.246 2.32,0.967 2.32,0.967 2.537,0.967 false 1.828,1.342 1.828,0.449 1.828,0.449 2.391,0.449 false

Set each brake line in the correct position on the brake actuator as shown in the illustration.

HINT:
·

*1: to front wheel cylinder RH

·

*2: to front wheel cylinder LH

·

*3: to rear wheel cylinder

·

*4: to master cylinder front

·

*5: to master cylinder rear




c.
A329093C03
1.719,0.542 2.031,0.698 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


Using a union nut wrench, connect the 5 brake lines to the correct locations on the actuator as shown in the illustration.

Torque:
Specified tightening torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.8661 in.)) + torque wrench (fulcrum length of 162 mm (6.3779 in.)): 13.4 N*m (137 kgf*cm, 10 ft.*lbf)




d.

Connect the connector.

NOTICE:

Make sure that the connector is locked securely.



Hide 2.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 4.BLEED CLUTCH LINE