Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR BUMPER (except Pickup) › 2016.08–2017.09
RM25T0E _59 Vehicle Exterior _029942 EXTERIOR PANELS / TRIM _0138267 REAR BUMPER(except Pickup) A

EXTERIOR PANELS / TRIM  REAR BUMPER(except Pickup)  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:

A bolt without a torque specification is shown in the standard bolt chart.

Click hereGeneral>SPECIFICATIONS>STANDARD BOLT>SPECIFIED TORQUE FOR STANDARD BOLTS


PROCEDURE

Hide 52109A 1.INSTALL REAR SIDE BUMPER SUB-ASSEMBLY LH

a.

Install the rear side bumper sub-assembly LH with the 2 nuts.


Hide 52108B 2.INSTALL REAR BUMPER SIDE EXTENSION SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the rear side bumper sub-assembly LH.


Hide 52186B 3.INSTALL REAR BUMPER SIDE MOUNTING BRACKET LH

a.

Install the rear bumper side mounting bracket LH with 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 52185B 4.INSTALL REAR BUMPER SIDE MOUNTING BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 52174E 5.INSTALL REAR BUMPER BAR BRACKET LH

a.

Install the rear bumper bar bracket LH with the 3 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 52173E 6.INSTALL REAR BUMPER BAR BRACKET RH

HINT:

Use the same procedure described for the LH side.


Hide 52176A 7.INSTALL REAR BUMPER ARM MOUNTING BRACKET LH (for Model Code #J76 Series)

a.

Install a new grommet.


b.

Install the rear bumper arm mounting bracket LH with screw.


Hide 52175 8.INSTALL REAR BUMPER ARM MOUNTING BRACKET (for Model Code #J76 Series)

HINT:

Use the same procedure described for the LH side.


Hide 52553 9.INSTALL REAR BUMPER FILLER LH

HINT:

When installing the rear bumper filler LH, heat the vehicle body using a heat light.


Standard:
Item Temperature
Vehicle Body 40 to 60°C (104 to 140°F)


NOTICE:

Do not heat the vehicle body excessively.


a.

Clean the vehicle body surface.

i.

Using a heat light, heat the vehicle body surface.


ii.

Remove the double-sided tape from the vehicle body surface.


iii.

Wipe off any tape adhesive residue with cleaner.



b.

Install a new rear bumper filler LH.

i.

Remove the peeling paper from the rear bumper filler LH.

HINT:

After removing the peeling paper, keep the exposed adhesive free from foreign matter.



ii.

for Model Code #J76 Series:

1.

Install the rear bumper filler LH with 4 new grommets.

HINT:

Press the rear bumper filler LH firmly to install it.


2.

Install the 4 screws.



iii.

except Model Code #J76 Series:

1.

Install the rear bumper filler LH with 3 new grommets.

HINT:

Press the rear bumper filler LH firmly to install it.


2.

Install the 2 screws.

3.

Install the rear bumper arm mounting bracket LH with the 2 screws.

4.

Install a new grommet.




Hide 52552 10.INSTALL REAR BUMPER FILLER RH

HINT:

Use the same procedure described for the LH side.


Hide 52359 11.INSTALL REAR BUMPER STEP COVER LH (w/ Cover, w/ Rear Combination Light)

a.

for Model Code #J76 Series:

HINT:

When installing the rear bumper step cover LH, heat the rear bumper step cover LH using a heat light.


Standard:
Item Temperature
Rear Bumper Step Cover LH 20 to 30°C (68 to 86°F)


NOTICE:

Do not heat the rear bumper step cover LH excessively.


i.

Clean the rear bumper step cover LH surface.

1.

Using a heat light, heat the rear bumper step cover LH surface.

2.

Remove the double-sided tape from the rear bumper step cover LH.

3.

Wipe off any tape adhesive residue with cleaner.



ii.

Install the rear bumper step cover LH.

1.

Using a heat light, heat the rear bumper step cover LH.

2.

Install the double-sided tape in the position shown in the illustration.

HINT:
B460115C03
0.448,0.385 0.76,0.542 0.313,0.156 10 false *a 2.375,0.385 2.688,0.542 0.313,0.156 10 false *b 2.854,0.094 3.167,0.25 0.313,0.156 10 false *c 2.906,3.635 3.219,3.792 0.313,0.156 10 false *e 2.281,3.385 2.594,3.542 0.313,0.156 10 false *f 1.698,3.99 1.958,4.198 0.26,0.208 10 false *g 0.896,3.604 1.208,3.76 0.313,0.156 10 false *h 1.052,2.156 1.365,2.313 0.313,0.156 10 false *i 3.188,0.521 3.333,0.688 0.146,0.167 10 false *c 2.781,0.646 3.094,0.844 0.313,0.198 10 false *d 0.844,1.073 1.313,1.229 0.469,0.156 10 false A-A 2.542,4.344 3.01,4.5 0.469,0.156 10 false B-B 2.479,1.354 2.635,1.552 0.156,0.198 10 false A 2.479,1.729 2.635,1.927 0.156,0.198 10 false A 0.521,2.531 0.677,2.729 0.156,0.198 10 false B 0.531,2.948 0.688,3.146 0.156,0.198 10 false B
*a 0.4 mm *b 29.0 mm
*c 5.0 mm *d 50.0 mm
*e 1.2 mm *f 4.0 mm
*g 10.0 mm *h 1.0 mm
*i 195.0 mm - -


Cut the double-sided tape to the dimensions shown in the illustration


3.
B560746C01
0,0 0,0 false
V100135

Nut
V100136

Nut and Washer


Install the rear bumper step cover LH with the 4 nuts and 2 washers.

HINT:

Press the rear bumper step cover LH firmly to install it.



Torque:
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)



b.

except Model Code #J76 Series:

i.
B560747C01
0,0 0,0 false
V100135

Nut
V100136

Nut and Washer


Install the rear bumper step cover LH with the 5 nuts and 3 washers.

Torque:
Nut : 5.5 N*m (56 kgf*cm, 49 in.*lbf)



Hide 52358B 12.INSTALL REAR BUMPER STEP COVER RH (w/ Cover, w/ Rear Combination Light)

HINT:

Use the same procedure described for the LH side.


Hide 81920 13.INSTALL REFLEX REFLECTOR ASSEMBLY LH

a.

Attach the clip and claw to install the reflex reflector assembly LH.


Hide 81910 14.INSTALL REFLEX REFLECTOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52069 15.INSTALL REAR BUMPER BAR SUB-ASSEMBLY LH

a.

Install the rear bumper bar sub-assembly LH with the 3 nuts.

Torque:
41 N*m (418 kgf*cm, 30 ft.*lbf)


b.

Install the 2 bolts.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 52019A 16.INSTALL REAR BUMPER BAR SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 52153B 17.INSTALL REAR BUMPER EXTENSION LH

a.

for Model Code #J76 Series:

i.

Install the rear bumper extension LH with 3 nuts and bolt.

Torque:
for nut : 12 N*m (122 kgf*cm, 9 ft.*lbf)


ii.

Install 2 new grommets.


iii.

Install the 2 screws.



b.

except Model Code #J76 Series:

i.

Attach the guide to install the rear bumper extension LH.


ii.

Install the 3 nuts and bolt.

Torque:
for nut : 12 N*m (122 kgf*cm, 9 ft.*lbf)


iii.

Install the screw.



Hide 52152B 18.INSTALL REAR BUMPER EXTENSION RH

HINT:

Use the same procedure described for the LH side.


Hide 52303A 19.INSTALL REAR BUMPER STEP SUB-ASSEMBLY LH (w/ Pintle Hook)

a.
B380333C01
1.719,1.406 1.896,1.583 0.177,0.177 10 true *a 0.542,1.854 0.719,2.042 0.177,0.188 10 true *a 2.208,1.969 2.521,2.167 0.313,0.198 10 false *b 1.927,1.635 2.104,1.813 0.177,0.177 10 true *a
*a Bolt A
*b Bolt B


Install the rear bumper step sub-assembly LH with the 3 bolts.

Torque:
Bolt A : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Install the bolt.

Torque:
Bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 52302A 20.INSTALL REAR BUMPER STEP SUB-ASSEMBLY (w/ Pintle Hook)

HINT:

Use the same procedure described for the LH side.


Hide 52350 21.INSTALL REAR BUMPER STEP ASSEMBLY

a.
B380301C01
0.115,1.417 0.281,1.615 0.167,0.198 10 true *a 2.469,1.646 2.646,1.844 0.177,0.198 10 true *a 0.771,1.563 0.958,1.729 0.188,0.167 10 true *b 1.677,1.625 1.865,1.792 0.188,0.167 10 true *b
*a Bolt A
*b Bolt B


Install the rear bumper step assembly with the 2 bolts.

Torque:
Bolt A : 18 N*m (184 kgf*cm, 13 ft.*lbf)


b.

Install the 2 bolts.

Torque:
Bolt B : 12 N*m (122 kgf*cm, 9 ft.*lbf)


Hide 52566 22.INSTALL REAR BUMPER EXTENSION FILLER LH (for Model Code #J76 Series)

a.

Install the rear bumper extension filler LH with the 2 bolts.


b.

Install the 2 hole plugs.


Hide 52565 23.INSTALL REAR BUMPER EXTENSION FILLER RH (for Model Code #J76 Series)

a.

Install the rear bumper extension filler RH with the 3 bolts.


b.

Install the 3 hole plugs.


Hide 81560 24.INSTALL REAR COMBINATION LIGHT ASSEMBLY LH (w/ Rear Combination Light)

Hide 81550 25.INSTALL REAR COMBINATION LIGHT ASSEMBLY RH (w/ Rear Combination Light)

HINT:

Use the same procedure described for the LH side.


Hide 61608B 26.INSTALL REAR WHEEL OPENING EXTENSION SUB-ASSEMBLY LH (for Model Code #J71 Series)

Hide 61607B 27.INSTALL REAR WHEEL OPENING EXTENSION SUB-ASSEMBLY RH (for Model Code #J71 Series)

HINT:

Use the same procedure described for the LH side.


Hide 76608 28.INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY LH (w/ Mudguard)

Hide 76607 29.INSTALL REAR QUARTER PANEL MUDGUARD SUB-ASSEMBLY RH (w/ Mudguard)

HINT:

Use the same procedure described for the LH side.