Home › Vehicle Interior › INTERIOR PANELS / TRIM › ROOF HEADLINING (for Single Cab) › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029934 INTERIOR PANELS / TRIM _0142494 ROOF HEADLINING(for Single Cab) A

INTERIOR PANELS / TRIM  ROOF HEADLINING(for Single Cab)  REMOVAL  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 67914 1.REMOVE FRONT DOOR SCUFF PLATE LH

a.
B235520

Remove the 4 screws and front door scuff plate LH.


Hide 67913 2.REMOVE FRONT DOOR SCUFF PLATE RH

HINT:

Use the same procedure described for the LH side.


Hide 62112A 3.REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH

a.
B386296

Remove the cap nut.


b.

Detach the clip and remove the cowl side trim sub-assembly LH.


Hide 62111A 4.REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 62316C 5.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP LH

a.
B234364

Remove the front door rear opening trim weatherstrip LH.


Hide 62315E 6.REMOVE FRONT DOOR REAR OPENING TRIM WEATHERSTRIP RH

HINT:

Use the same procedure described for the LH side.


Hide 55356B 7.REMOVE INSTRUMENT PANEL PLATE LH

Hide 55355B 8.REMOVE INSTRUMENT PANEL PLATE RH

Hide 74617A 9.REMOVE ASSIST GRIP PLUG

HINT:

Use the same procedure for all assist grip plugs.


a.
B234351C03
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, detach the 2 claws and remove the assist grip plug.

HINT:

Tape the screwdriver tip before use.



Hide 74603 10.REMOVE FRONT ASSIST GRIP SUB-ASSEMBLY

HINT:

Use the same procedure for both front assist grip sub-assemblies.


a.
B234353

Remove the 2 screws and front assist grip sub-assembly.


Hide 62212 11.REMOVE FRONT PILLAR GARNISH LH

a.
B234354

w/o Knee Airbag:

Detach the claw and clip and remove the front pillar garnish LH.


b.

w/ Driver Side Knee Airbag:

i.
B452041

Detach the clip.


ii.
B452042

Remove the front pillar garnish LH as indicated by the arrow shown in the illustration.


iii.
B452043

Using a clip remover, remove the clip from vehicle side.



Hide 62211 12.REMOVE FRONT PILLAR GARNISH RH

a.
B234355

w/o Assist Grip:

i.

Using a clip remover, remove the 2 clips.

HINT:

Tape the clip remover tip before use.



ii.

Detach the claw and clip and remove the front pillar garnish RH.



b.

w/o Knee Airbag:

HINT:

Use the same procedure described for the LH side.



c.

w/ Driver Side Knee Airbag:

HINT:

Use the same procedure described for the LH side.



Hide 73174 13.REMOVE FRONT SEAT BELT HOLE COVER LH (w/o Knee Airbag)

a.
B234359

Using moulding remover, detach the 2 claws and 2 guides, and remove the front seat belt hole cover LH.


Hide 73173 14.REMOVE FRONT SEAT BELT HOLE COVER RH (w/o Knee Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 58707A 15.REMOVE JACK HOLDER SUB-ASSEMBLY (w/o Knee Airbag)

a.
B234357

Remove the 2 bolts and jack holder sub-assembly.


Hide 62412 16.REMOVE CENTER PILLAR GARNISH LH

a.

w/o Knee Airbag:

i.
B233858C04
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, detach the 2 claws and open the front seat belt shoulder anchor cover.

HINT:

Tape the screwdriver tip before use.



ii.
B233859

Loosen the bolt and disconnect the front seat belt shoulder anchor.


iii.
B234356

Loosen the bolt and disconnect the front seat belt floor anchor.


iv.
B234358

Remove the 3 clips.


v.

Detach the 5 clips and remove the center pillar garnish LH.



b.

w/ Driver Side Knee Airbag:

i.
B452040

Remove the bolt and disconnect the front seat belt floor anchor.


ii.
B461230

Remove the 2 clips.


iii.

Detach the 6 clips.


iv.
B461229

Remove the center pillar garnish LH as indicated by the arrow shown in the illustration.


v.
B461227

Using a clip remover, remove the 2 clips from vehicle side.



Hide 62411 17.REMOVE CENTER PILLAR GARNISH RH

HINT:

Use the same procedure described for the LH side.


Hide 73024 18.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY LH (w/ Driver Side Knee Airbag)

a.
B452003

Detach the 6 guides and remove the front shoulder belt anchor plate sub-assembly LH as shown in the illustration.


Hide 73023 19.REMOVE FRONT SHOULDER BELT ANCHOR PLATE SUB-ASSEMBLY RH (w/ Driver Side Knee Airbag)

HINT:

Use the same procedure described for the LH side.


Hide 74617C 20.REMOVE ASSIST GRIP PLUG

HINT:

Use the same procedure for all assist grip plugs.


a.
B234351C04
0,0 0,0 false
V100155

Protective Tape


Using a screwdriver, detach the 2 claws and remove the assist grip plug.

HINT:

Tape the screwdriver tip before use.



Hide 74610A 21.REMOVE ASSIST GRIP SUB-ASSEMBLY

a.
B234352

Remove the 2 screws and assist grip sub-assembly.


Hide 87827 22.REMOVE INNER REAR VIEW MIRROR ABSORBER

Hide 87834 23.REMOVE INNER REAR VIEW MIRROR STAY HOLDER COVER

Hide 87810 24.REMOVE INNER REAR VIEW MIRROR ASSEMBLY

Hide 81290 25.REMOVE NO. 3 ROOM LIGHT ASSEMBLY

Hide 74320 26.REMOVE VISOR ASSEMBLY LH

a.
B234361

Remove the 2 screws and visor assembly LH.


Hide 74310 27.REMOVE VISOR ASSEMBLY RH

HINT:

Use the same procedure described for the LH side.


Hide 74348 28.REMOVE VISOR HOLDER

HINT:

Use the same procedure for both visor holders.


a.
B234362

Remove the screw.


b.

Detach the clip and remove the visor holder.


Hide 63310 29.REMOVE ROOF HEADLINING ASSEMBLY

a.

w/o Knee Airbag:

i.
B234363

Using a clip remover, remove the 8 clips.

HINT:

Tape the clip remover tip before use.



ii.
B234365

Remove the roof headlining assembly from the front door as shown in the illustration.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.





b.
B452004

w/ Driver Side Knee Airbag:

i.

Using a clip remover, remove the 4 clips.

HINT:

Tape the clip remover tip before use.



ii.
B452005

Remove the roof headlining assembly from the front door as shown in the illustration.

NOTICE:
·

Make sure wrinkles do not form in the roof headlining assembly during removal.

·

Make sure that the roof headlining assembly does not get caught on anything as it may become bent or damaged.

·

Do not damage the roof headlining assembly or vehicle interior.