Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT AIRBAG SENSOR › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138002 FRONT AIRBAG SENSOR A

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT AIRBAG SENSOR  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 89174A 1.INSTALL FRONT AIRBAG SENSOR LH

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the battery negative (-) terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

w/o Curtain Shield Airbag

i.

Attach the guide and hold the front airbag sensor LH in place.


ii.

Install the nut.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

·

When installing the front airbag sensor LH, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

·

Tighten the nut while holding the front airbag sensor LH because the front airbag sensor LH guide is easily damaged.





d.

w/ Curtain Shield Airbag

i.

Attach the guide and hold the front airbag sensor LH in place.


ii.

Install the bolt.

Torque:
9.0 N*m (92 kgf*cm, 80 in.*lbf)

NOTICE:
·

If the front airbag sensor LH has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.

·

When installing the front airbag sensor LH, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

·

Tighten the bolt while holding the front airbag sensor LH because the front airbag sensor LH guide is easily damaged.





e.

Connect the airbag connector.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.


i.

Before connecting the connector, check that the position of the housing lock is correct as shown in the illustration.

B340848C02
4.583,0.594 4.896,0.75 0.313,0.156 10 *a 4.677,1.875 4.99,2.031 0.313,0.156 10 *b 1.385,0.615 1.698,0.771 0.313,0.156 10 *a 1.448,1.865 1.76,2.021 0.313,0.156 10 *b
*a Incorrect *b Correct



ii.

While holding the CPA be sure to engage the connectors until they are locked and check that the CPA is in its original position (when locking, make sure that a click sound can be heard).

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and upper part of the CPA, as it may result in an insecure fit.


B340850C07
2.271,1.198 2.5,1.76 2.5,1.76 2.729,1.76 false 2.438,1.01 2.844,0.521 2.844,0.521 3.115,0.521 true 1.521,1.125 1.792,1.125 1.792,1.125 2.083,0.917 true 3.167,0.417 3.479,0.573 0.313,0.156 10 false *a 2.781,1.656 3.094,1.813 0.313,0.156 10 false *b 5.823,2.073 6.135,2.229 0.313,0.156 10 false *d 1.365,1.021 1.823,1.219 0.458,0.198 10 false *c
*a Housing Lock *b CPA
*c CPA Upper Part *d Connection is Completed




f.

Check that there is no looseness in the installation parts of the front airbag sensor LH.


Hide 2.INSTALL HEADLIGHT ASSEMBLY LH (w/ Curtain Shield Airbag)

Hide 4.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL