Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2016.08–2017.01
RM25T0E _57 Power Source / Network _057931 NETWORKING _0285332 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  Skid Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Skid Control ECU Communication Stop Mode Either condition is met:
·

"Skid Control (ABS/VSC/TRAC)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Skid Control ECU Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of brake actuator assembly (skid control ECU)

·

Brake actuator assembly (skid control ECU) ground circuit

·

Brake actuator assembly (skid control ECU) CAN branch wire or connector

·

Brake actuator assembly (skid control ECU)



WIRING DIAGRAM

C364741E01
2.031,2.604 3.865,2.802 1.833,0.198 10 false from Battery 2.01,3.063 3.844,3.26 1.833,0.198 10 false from Battery 1.75,3.594 3.583,3.792 1.833,0.198 10 false from IG1 1 Relay 3.948,3.813 5.781,4.01 1.833,0.198 10 false ECU IG 3.906,2.823 5.74,3.021 1.833,0.198 10 false ABS MTR 3.906,3.292 5.74,3.49 1.833,0.198 10 false ABS SOL 5.542,3.094 6.479,3.5 0.938,0.406 10 false +BS 5.542,2.625 6.479,3.031 0.938,0.406 10 false BM 5.552,0.969 6.49,1.375 0.938,0.406 10 false CANH 5.552,1.458 6.49,1.865 0.938,0.406 10 false CANL 0.469,1.927 2.469,2.146 2,0.219 10 false I111 0.469,2.083 2.469,2.302 2,0.219 10 false No. 5 CAN Junction Connector 1.563,1.385 2.5,1.792 0.938,0.406 10 false 10 1.552,0.885 2.49,1.292 0.938,0.406 10 false 4 5.24,1.385 6.177,1.792 0.938,0.406 10 false 10 5.229,0.875 6.167,1.281 0.938,0.406 10 false 22 5.26,2.51 5.521,2.885 0.26,0.375 10 false 13 5.26,2.979 5.521,3.354 0.26,0.375 10 false 38 5.25,3.469 5.51,3.844 0.26,0.375 10 false 12 5.542,3.583 6.479,3.99 0.938,0.406 10 false IG1 5.542,4.24 6.479,4.646 0.938,0.406 10 false GND1 5.542,4.74 6.479,5.146 0.938,0.406 10 false GND2 5.25,4.188 5.51,4.563 0.26,0.375 10 false 25 5.323,4.656 5.583,5.031 0.26,0.375 10 false 1 5.146,5.625 6.792,5.979 1.646,0.354 10 false A42 5.156,5.781 6.802,6.135 1.646,0.354 10 false Brake Actuator Assembly (Skid Control ECU)

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SKID CONTROL ECU CAN BRANCH WIRE)
a.
C364734C02
0.573,0.208 1.063,0.427 0.49,0.219 2.094,1.052 2.552,0.458 2.552,0.458 2.719,0.458 true 2.042,1.167 1.813,0.188 1.813,0.188 1.979,0.188 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,0.229 0.99,0.385 0.313,0.156 10 false A42 2.781,0.354 3.281,0.594 0.5,0.24 10 false CANL 2.031,0.104 2.531,0.344 0.5,0.24 10 false CANH
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the brake actuator assembly (skid control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-22 (CANH) - A42-10 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE SKID CONTROL ECU CAN BRANCH WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - BATTERY AND BODY GROUND)
a.
C364734C03
0.573,0.208 1.063,0.427 0.49,0.219 2.573,1.031 2.76,0.479 2.76,0.479 2.927,0.479 true 2.292,1.052 2.49,0.24 2.49,0.24 2.656,0.24 true 2.573,1.344 2.677,1.958 2.677,1.958 2.844,1.958 true 0.51,1.938 0.698,1.938 0.698,1.938 0.854,1.344 true 0.5,0.573 0.688,0.573 0.688,0.573 0.823,1.031 true 0.125,0.094 0.438,0.25 0.313,0.156 10 false *a 0.677,0.229 0.99,0.385 0.313,0.156 10 false A42 2.99,0.385 3.333,0.594 0.344,0.208 10 false BM 2.906,1.885 3.302,2.146 0.396,0.26 10 false +BS 0.073,1.833 0.469,2.094 0.396,0.26 10 false GND1 2.708,0.115 3.052,0.323 0.344,0.208 10 false IG1 0.063,0.469 0.458,0.729 0.396,0.26 10 false GND2
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-13 (BM) - Body ground Always 11 to 14 V
A42-38 (+BS) - Body ground Always 11 to 14 V
A42-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-25 (GND1) - Body ground Always Below 1 Ω
A42-1 (GND2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR