Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM(w/ VSC) › 2016.08–2017.01
RM25T0E _57 Power Source / Network _057931 NETWORKING _0285332 CAN COMMUNICATION SYSTEM(w/ VSC) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ VSC)  ECM Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
ECM Communication Stop Mode Either condition is met:
·

"ECM (Engine)" is not displayed on "CAN Bus Check".

(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "ECM Communication Stop Mode" in "DTC Combination Table".

(Click here)


·

Power source circuit of ECM

·

ECM ground circuit

·

ECM CAN main wire or connector

·

ECM



WIRING DIAGRAM

C363544E01
5.604,0.438 6.219,0.635 0.615,0.198 10 false CANH 5.604,1.167 6.219,1.365 0.615,0.198 10 false CANL 5.25,0.333 5.865,0.531 0.615,0.198 10 false 41 5.25,0.854 5.865,1.052 0.615,0.198 10 false 49 5.208,0.531 5.823,0.729 0.615,0.198 10 false A29 5.208,1.063 5.823,1.26 0.615,0.198 10 false A29 1.542,0.427 2.156,0.625 0.615,0.198 10 false 3 1.563,0.917 2.177,1.115 0.615,0.198 10 false 9 0.313,1.438 0.927,1.635 0.615,0.198 10 false I111 0.292,1.594 2.354,1.823 2.063,0.229 10 false No. 5 CAN Junction Connector 1.781,1.917 3.844,2.146 2.063,0.229 10 false from Battery 3.823,2.125 4.99,2.49 1.167,0.365 10 false EFI MAIN 1.51,2.448 2.677,2.813 1.167,0.365 10 false from MAIN Relay 1.625,3.406 2.792,3.771 1.167,0.365 10 false to MAIN Relay 4.052,4.167 5.219,4.531 1.167,0.365 10 false IGN 1.365,3.958 2.875,4.302 1.51,0.344 10 false from Ignition Switch 5.646,1.948 6.208,2.281 0.563,0.333 10 false BATT 5.208,1.927 5.823,2.125 0.615,0.198 10 false A29 5.208,2.479 5.823,2.677 0.615,0.198 10 false A29 5.208,3.458 5.823,3.656 0.615,0.198 10 false A29 5.198,3.99 5.813,4.188 0.615,0.198 10 false A29 5.229,5.958 5.844,6.156 0.615,0.198 10 false A29 5.208,5.479 5.823,5.677 0.615,0.198 10 false C39 5.208,4.99 5.823,5.188 0.615,0.198 10 false C39 5.219,4.51 5.833,4.708 0.615,0.198 10 false C39 5.646,2.49 6.208,2.823 0.563,0.333 10 false +B 5.615,3.448 6.177,3.781 0.563,0.333 10 false MREL 5.604,4 6.167,4.333 0.563,0.333 10 false IGSW 5.604,4.49 6.167,4.823 0.563,0.333 10 false E01 5.604,4.979 6.167,5.313 0.563,0.333 10 false E05 5.604,5.469 6.167,5.802 0.563,0.333 10 false E1 5.604,5.948 6.167,6.281 0.563,0.333 10 false EC 5.271,5.74 5.833,6.073 0.563,0.333 10 false 32 5.271,5.281 5.833,5.615 0.563,0.333 10 false 81 5.26,4.781 5.823,5.115 0.563,0.333 10 false 23 5.26,4.313 5.823,4.646 0.563,0.333 10 false 22 5.229,3.792 5.792,4.125 0.563,0.333 10 false 28 5.25,3.25 5.813,3.583 0.563,0.333 10 false 44 5.281,2.281 5.844,2.615 0.563,0.333 10 false 2 5.25,1.729 5.813,2.063 0.563,0.333 10 false 20 5.833,6.417 6.396,6.75 0.563,0.333 10 false ECM 5.615,2.979 6.177,3.313 0.563,0.333 10 false +B2 5.208,3.01 5.823,3.208 0.615,0.198 10 false A29 5.292,2.813 5.854,3.146 0.563,0.333 10 false 1

CAUTION / NOTICE / HINT

NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Drive the vehicle for 3 seconds at a speed of 15 km/h (9 mph) or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (ECM CAN MAIN WIRE)
a.
C363469C01
1.49,0.292 2.094,0.552 0.604,0.26 2.427,1.354 2.656,1.167 2.656,1.167 2.823,1.167 true 2.427,1.458 2.625,1.938 2.625,1.938 2.792,1.938 true 0.135,0.094 0.448,0.25 0.313,0.156 10 false *a 2.875,1.042 3.385,1.292 0.51,0.25 10 false CANH 2.833,1.823 3.344,2.073 0.51,0.25 10 false CANL 1.667,0.313 2.177,0.563 0.51,0.25 10 false A29
*a Front view of wire harness connector
(to ECM)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-41 (CANH) - A29-49 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)

NG

REPAIR OR REPLACE ECM CAN MAIN WIRE OR CONNECTOR (CANH, CANL)

2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY AND BODY GROUND)
a.

Connect the cable to the negative (-) battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION


C234869C14
1.99,0.49 2.458,0.76 0.469,0.271 4.594,0.5 5.063,0.771 0.469,0.271 1.542,0.708 1.76,0.708 1.76,0.708 1.958,1.219 true 5.688,1.208 6.25,0.823 6.25,0.823 6.469,0.823 true 5.813,2.313 5.51,2.313 5.51,2.313 5.208,1.646 true 1.115,1.01 1.333,1.01 1.333,1.01 1.865,1.385 true 1.896,2.5 2.115,2.5 2.115,2.5 2.344,1.719 true 1.229,2.198 1.448,2.198 1.448,2.198 1.938,1.677 true 5.583,1.208 5.854,0.604 5.854,0.604 6.073,0.604 true 2.094,0.51 2.385,0.688 0.292,0.177 10 false A29 0.125,0.073 0.417,0.25 0.292,0.177 10 false *a 6.135,0.5 6.677,0.802 0.542,0.302 10 false E01 5.875,2.198 6.74,2.365 0.865,0.167 10 false E1 4.698,0.521 5.031,0.698 0.333,0.177 10 false C39 0.76,0.917 1.188,1.083 0.427,0.167 10 false BATT 1.281,0.604 1.708,0.771 0.427,0.167 10 false +B 1.469,2.396 1.896,2.563 0.427,0.167 10 false MREL 0.958,2.094 1.385,2.26 0.427,0.167 10 false EC 6.531,0.729 7.073,1.031 0.542,0.302 10 false E05
*a Front view of wire harness connector
(to ECM)
- -



b.

Disconnect the ECM connector.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A29-20 (BATT) - Body ground Always 11 to 14 V
A29-2 (+B) - Body ground Battery positive (+) voltage applied to terminal A29-44 (MREL) 11 to 14 V
A29-1 (+B2) - Body ground Battery positive (+) voltage applied to terminal A29-44 (MREL) 11 to 14 V
A29-28 (IGSW) - Body ground Ignition switch ON 11 to 14 V



d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A29-32 (EC) - Body ground Always Below 1 Ω
C39-22 (E01) - Body ground Always Below 1 Ω
C39-23 (E05) - Body ground Always Below 1 Ω
C39-81 (E1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR