Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  TS and CG Terminal Circuit  


DESCRIPTION

In Test Mode (signal check), a malfunction in the speed sensor that cannot be detected when the vehicle is stopped can be detected while driving.

Sensor check mode can be entered by connecting terminals TS and CG of the DLC3 and turning the ignition switch from off to ON.

WIRING DIAGRAM

C173350E29
0.917,0.885 1.188,1.063 0.271,0.177 10 false TS 0.917,1.771 1.188,1.948 0.271,0.177 10 false CG 5.417,3.021 6.958,3.427 1.542,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 0.479,2.885 0.927,3.063 0.448,0.177 10 false I17 0.5,3.052 0.948,3.229 0.448,0.177 10 false DLC3 1.313,1.583 1.563,1.76 0.25,0.177 10 false 4 1.26,0.708 1.635,0.885 0.375,0.177 10 false 12 6.052,0.896 6.323,1.073 0.271,0.177 10 false TS 5.406,2.885 5.677,3.063 0.271,0.177 10 false A42 5.729,0.708 5.948,0.885 0.219,0.177 10 false 24

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - TS of DLC3)
a.

Turn the ignition switch off.


b.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-24 (TS) - I17-12 (TS) Always Below 1 Ω
A42-24 (TS) or I17-12 (TS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (CG of DLC3 - BODY GROUND)
a.
C269109C82
0.115,1.49 0.479,1.719 0.365,0.229 1.302,0.281 1.573,0.792 true 1.073,0.198 1.417,0.438 0.344,0.24 10 false CG 0.167,0.167 0.479,0.323 0.313,0.156 10 false *a 0.208,1.521 0.521,1.719 0.313,0.198 10 false I17
*a Front view of DLC3


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I17-4 (CG) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR