Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1210  Zero Point Calibration of Yaw Rate Sensor Undone  C1336  Zero Point Calibration of Acceleration Sensor Undone  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via the CAN communication system.

The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle condition. If there is trouble in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, the DTC U0124 (Lost Communication with Lateral Acceleration Sensor Module) is output.

The DTCs are also output when the calibration has not been completed.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1210 Zero Point Calibration of Yaw Rate Sensor Undone Zero point calibration of yaw rate sensor undone.
·

Sensor installation

·

Yaw rate sensor (Airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)


C1336 Zero Point Calibration of Acceleration Sensor Undone Zero point calibration of acceleration sensor undone.
·

Sensor installation

·

Acceleration sensor (Airbag sensor assembly)

·

Skid control ECU (Brake actuator assembly)



CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION

·

When replacing the yaw rate and acceleration sensor (airbag sensor assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION



HINT:

When U0124 and/or U0126 is output along with C1210 and/or C1336, inspect and repair trouble areas indicated by U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>U0073


PROCEDURE

1.PERFORM ZERO POINT CALIBRATION OF YAW RATE AND ACCELERATION SENSOR
a.

Perform zero point calibration of the yaw rate and acceleration sensor.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


Result:
Proceed to
NEXT



NEXT

2.PERFORM TEST MODE (SIGNAL CHECK)
2.PERFORM TEST MODE (SIGNAL CHECK)
a.

Turn the ignition switch off.


b.

Using the GTS, perform a Test Mode (signal check) inspection sensor check and check that all Test Mode (signal check) inspection items change from incomplete to complete.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>TEST MODE PROCEDURE

Chassis > ABS/VSC/TRC > Utility
Tester Display
Signal Check
50005 105 4359
OK:

All Test Mode (signal check) inspection items change from incomplete to complete.


HINT:

If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

END

NG

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Turn the ignition switch off.


b.

Check that the airbag sensor assembly has been installed properly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION

OK:

The sensor is tightened to the specified torque.

The sensor is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)

NG

4.READ VALUE USING GTS (YAW RATE AND ACCELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


e.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Deceleration Sensor Acceleration sensor Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Deceleration Sensor2 Acceleration sensor 2 Min.: -18.525 m/s2, Max.: 18.387 m/s2 - During deceleration/acceleration: Changes continuously
Yaw Rate Sensor Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
Deceleration Sensor
Deceleration Sensor2
Yaw Rate Sensor
50003 105 14,15,24
f.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.


Result:
Proceed to
OK
NG




OK

NG