Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1225  SM Solenoid Circuit  C1468  SFR Solenoid Circuit  C1469  SFL Solenoid Circuit  C146A  SRR Solenoid Circuit  C146B  SRL Solenoid Circuit  


DESCRIPTION

These solenoids turn on when signals are received from the skid control ECU (brake actuator assembly) and they control the pressure acting on the wheel cylinders to control the braking force.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1225 SM Solenoid Circuit Any of the following is detected:
1.

While master cylinder cut solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

2.

While master cylinder cut solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While master cylinder cut solenoid outputs ON, open circuit continues for 0.05 seconds or more.

4.

While master cylinder cut solenoid outputs OFF, current is maintained for 0.05 seconds or more.

5.

Difference in master cylinder cut solenoid output accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C1468 SFR Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C1469 SFL Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C146A SRR Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly
C146B SRL Solenoid Circuit Any of the following is detected:
1.

Open or short circuit in decompression solenoid continues for 0.05 seconds or more.

2.

While holding solenoid outputs OFF, open circuit continues for 0.05 seconds or more.

3.

While holding solenoid outputs OFF, current is maintained for 0.05 seconds or more.

4.

While holding solenoid outputs ON, overcurrent continues for 0.1 seconds or more.

5.

While holding solenoid outputs ON, open circuit continues for 0.05 seconds or more.

6.

Difference in holding solenoid LH and RH accuracy continues for 0.2 seconds or more.


Brake actuator assembly

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.RECONFIRM DTC
HINT:

These codes are detected when a problem is determined in the skid control ECU (brake actuator assembly).

The solenoid circuits are in the skid control ECU (brake actuator assembly).

Therefore, solenoid circuit inspection and solenoid unit inspection cannot be performed. Be sure to check if any DTCs are output before replacing the skid control ECU (brake actuator assembly).



b.

Turn the ignition switch off.


c.

Start the engine.


d.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


e.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output


HINT:
·

If a speed signal of 6 km/h (4 mph) or more is input to the skid control ECU (brake actuator assembly) with the ignition switch turned to ON and the stop light switch off, the ECU performs self diagnosis of the motor and solenoid circuits.

·

If the normal system code is output (the trouble code is not output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly). Make sure that no DTCs are output.

·

If any DTCs are output while jiggling a connector or wire harness from the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

The DTCs were probably output due to a bad connection of the connector terminal.





DTC is not output

DTC is output