Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1425  Open in Stop Light Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) detects the brake operating conditions through a signal transmitted by the stop light switch assembly.

The skid control ECU incorporates a circuit to detect an open circuit. This DTC is output when an open circuit is detected in the stop light signal input line.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1425 Open in Stop Light Switch Circuit When voltage at terminal +BS is 9.5 to 17.4 V, open circuit occurs between STP terminal circuits A and B for 0.3 seconds or more.
·

Wire harnesss or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C325963E16
4.594,1.094 4.75,1.313 0.156,0.219 10 false B 4.854,2.219 5.313,2.417 0.458,0.198 10 false GND1 4.563,0.823 5.021,1.021 0.458,0.198 10 false 35 4.573,2.083 5.073,2.281 0.5,0.198 10 false 25 4.896,2.958 5.354,3.156 0.458,0.198 10 false A42 4.875,3.135 6.427,3.531 1.552,0.396 10 false Skid Control ECU (Brake Actuator Assembly) 0.125,0.958 2.448,1.323 2.323,0.365 10 false from Stop Light Switch Assembly 0.927,1.635 2.604,2.01 1.677,0.375 10 false to Stop Light Circuit 4.865,0.958 5.25,1.177 0.385,0.219 10 false STP 4.146,1.083 4.313,1.281 0.167,0.198 10 false A

CAUTION / NOTICE / HINT

NOTICE:

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION


PROCEDURE

1.CHECK STOP LIGHT OPERATION
a.

Check that all stop lights come on when the brake pedal is depressed, and go off when the brake pedal is released.

OK:
Condition Illumination Condition
Brake pedal depressed ON
Brake pedal released OFF



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)

NG

2.CHECK HARNESS AND CONNECTOR (STP TERMINAL)
a.
C364797C04
1.542,0.104 1.917,0.333 0.375,0.229 2.677,1.885 2.677,1.74 2.677,1.74 2.271,1.281 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 2.542,1.948 2.969,2.177 0.427,0.229 10 false STP
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Turn the ignition switch off.


b.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.


c.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-35 (STP) - Body ground Stop light switch assembly on (Brake pedal depressed) 8 to 14 V
Stop light switch assembly off (Brake pedal released) Below 1.5 V



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BRAKE ACTUATOR ASSEMBLY - STOP LIGHT CIRCUIT)

3.RECONFIRM DTC
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Turn the ignition switch off.


d.

Start the engine.


e.

Depress the brake pedal several times to test the stop light circuit.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>PROBLEM SYMPTOMS TABLE


Result:
Proceed to
DTC C1425 is not output
DTC C1425 is output



DTC C1425 is not output

DTC C1425 is output