Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1432  Steering Angle Sensor Power Source Voltage Malfunction  


DESCRIPTION

The skid control ECU (brake actuator assembly) outputs this DTC when it receives a sensor power source malfunction signal from the steering angle sensor.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1432 Steering Angle Sensor Power Source Voltage Malfunction Steering angle sensor power supply malfunction signal is received from steering angle sensor.
·

ECU-B fuse

·

ECU IG fuse

·

Steering angle sensor (Spiral with sensor cable sub-assembly)

·

Wire harness or connector



WIRING DIAGRAM

C274776E47
0.823,0.677 1.438,0.875 0.615,0.198 10 false CANL 1.281,0.5 1.438,0.698 0.156,0.198 10 false 3 5.76,0.5 6.073,0.698 0.313,0.198 10 false 10 6.031,0.677 6.646,0.875 0.615,0.198 10 false CANL 0.802,1.26 1.417,1.458 0.615,0.198 10 false CANH 1.281,1.083 1.438,1.281 0.156,0.198 10 false 4 5.771,1.094 6.083,1.292 0.313,0.198 10 false 22 6.042,1.271 6.656,1.469 0.615,0.198 10 false CANH 0.906,1.958 1.365,2.156 0.458,0.198 10 false BAT 1.281,1.844 1.438,2.042 0.156,0.198 10 false 6 2.26,2.125 2.771,2.354 0.51,0.229 10 false ECU-B 3.917,1.948 4.74,2.146 0.823,0.198 10 false from Battery 1.031,2.615 1.344,2.813 0.313,0.198 10 false IG 1.281,2.51 1.438,2.708 0.156,0.198 10 false 5 2.24,2.792 2.75,3.021 0.51,0.229 10 false ECU IG 3.917,2.615 4.865,2.813 0.948,0.198 10 false from IG Circuit 0.896,3.281 1.354,3.479 0.458,0.198 10 false ESS 1.271,3.188 1.427,3.385 0.156,0.198 10 false 2 0.115,3.906 0.573,4.104 0.458,0.198 10 false L47 0.115,4.073 2.219,4.448 2.104,0.375 10 false Steering Angle Sensor (Spiral with Sensor Cable Sub-assembly) 2.875,4.375 4.635,4.583 1.76,0.208 10 false : CAN Communication Line 5.573,3.823 5.885,4.021 0.313,0.198 10 false A42 5.563,4 7.115,4.406 1.552,0.406 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove the steering angle sensor from the spiral with sensor cable sub-assembly.

·

When replacing the steering angle sensor (spiral with sensor cable sub-assembly), confirm that the replacement part is of the correct specification.

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



HINT:
·

When U0073, U0124 and/or U0126 is output together with C1432, inspect and repair the trouble areas indicated by U0073, U0124 and/or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>U0073

·

When the speed sensor or the yaw rate sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be output even when the steering angle sensor is normal. When DTCs for the speed sensor or yaw rate sensor (airbag sensor assembly) are output together with DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).



PROCEDURE

1.CHECK TERMINAL VOLTAGE (BAT TERMINAL)
a.

Turn the ignition switch off.


b.

Remove the steering wheel and the column cover lower.

Click hereSteering>STEERING COLUMN>STEERING COLUMN ASSEMBLY>REMOVAL


c.
C364760C01
0.24,1.167 0.615,1.417 0.375,0.25 2.354,1.885 2.354,1.5 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 2.24,1.917 2.594,2.125 0.354,0.208 10 false BAT
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly])


Make sure that there is no looseness at the locking part and the connecting part of the connectors.


d.

Disconnect the L47 steering angle sensor (spiral with sensor cable sub-assembly) connector.


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L47-6 (BAT) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (BAT CIRCUIT)

2.CHECK TERMINAL VOLTAGE (IG TERMINAL)
a.

Turn the ignition switch to ON.


b.
C364760C02
0.24,1.167 0.615,1.417 0.375,0.25 1.594,1.927 2.063,1.521 false 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 0.323,1.208 0.708,1.427 0.385,0.219 10 false L47 1.396,1.875 1.75,2.083 0.354,0.208 10 false IG
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly])


Measure the voltage according to the value(s) in the table below.


Standard Voltage:
Tester Connection Switch Condition Specified Condition
L47-5 (IG) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (ESS TERMINAL)
a.

Turn the ignition switch off.


b.
C364760C03
0.229,1.146 0.625,1.396 0.396,0.25 0.875,1.875 1.333,1.5 false 0.313,1.177 0.646,1.375 0.333,0.198 10 false L47 0.146,0.094 0.406,0.302 0.26,0.208 10 false *a 0.542,1.865 0.938,2.073 0.396,0.208 10 false ESS
*a Front view of wire harness connector
(to Steering Angle Sensor [Spiral with Sensor Cable Sub-assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L47-2 (ESS) - Body ground Always Below 1 Ω


HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
OK
NG



OK

REPLACE SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (ESS CIRCUIT)