Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › 2016.08–2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

If any of the following is detected, the ABS warning light remains on:

·

The skid control ECU (brake actuator assembly) connectors are disconnected from the skid control ECU (brake actuator assembly).

·

There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.

·

There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).

·

The ABS control system is defective.

·

w/ Rear Differential Lock:

When the rear differential lock is in the lock state, the ABS is also prohibited and the ABS warning light turns on during operation.


HINT:

In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM

C363588E01
0.698,5.906 4.208,6.104 3.51,0.198 10 false Differential Lock ECU (No. 2 4 Wheel Drive Control ECU)* 2.969,6.406 4.615,6.646 1.646,0.24 10 false *: w/ Rear Differential Lock 0.698,5.75 0.958,5.948 0.26,0.198 10 false I8 0.469,6.417 2.292,6.635 1.823,0.219 10 false : CAN Communication Line 5.573,5.219 7.104,5.583 1.531,0.365 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,5.031 5.948,5.25 0.365,0.219 10 false A42 2.594,4.646 4.906,5.031 2.313,0.385 10 false Rear Differential Lock Position Switch (No. 4 Transfer Indicator Switch)* 2.594,4.49 2.906,4.698 0.313,0.208 10 false V1 5.854,4.094 6.302,4.302 0.448,0.208 10 false EXI3* 5.563,3.729 5.76,3.938 0.198,0.208 10 false 23 5.854,0.448 6.135,0.677 0.281,0.229 10 false IG1 5.594,2.792 5.792,3 0.198,0.208 10 false 25 5.865,2.917 6.323,3.135 0.458,0.219 10 false GND1 5.833,3.823 6.375,4.021 0.542,0.198 10 false FSW+* 5.604,4.094 5.802,4.302 0.198,0.208 10 false 11 5.854,1.323 6.333,1.521 0.479,0.198 10 false CANL 5.844,1.885 6.323,2.083 0.479,0.198 10 false CANH 1.813,1.854 2.292,2.052 0.479,0.198 10 false CANH 1.844,1.354 2.323,1.552 0.479,0.198 10 false CANL 2.26,0.448 3.229,0.635 0.969,0.188 10 false from IG Circuit 4.135,0.615 4.656,0.802 0.521,0.188 10 false ECU IG 5.563,1.677 5.76,1.885 0.198,0.208 10 false 22 5.542,0.333 5.74,0.542 0.198,0.208 10 false 12 5.563,1.146 5.76,1.354 0.198,0.208 10 false 10 2.396,1.125 2.594,1.333 0.198,0.208 10 false 14 2.396,1.635 2.594,1.844 0.198,0.208 10 false 13 1.708,3.063 2.25,3.271 0.542,0.208 10 false RRSW* 2.396,2.844 2.677,3.021 0.281,0.177 10 false 17 0.854,3.594 2.729,3.823 1.875,0.229 10 false Combination Meter Assembly 3.885,4.094 4.063,4.302 0.177,0.208 10 false 2 3.063,4.104 3.24,4.313 0.177,0.208 10 false 1 2.01,5.146 2.375,5.365 0.365,0.219 10 false RLP 2.448,5.125 2.625,5.333 0.177,0.208 10 false 2 2.375,1.354 2.698,1.563 0.323,0.208 10 false L26 2.365,1.865 2.688,2.073 0.323,0.208 10 false L26 2.365,3.073 2.719,3.26 0.354,0.188 10 false L25

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.CHECK CAN COMMUNICATION SYSTEM
a.

Check if CAN communication system DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM


Result:
Proceed to
DTC is not output
DTC is output



DTC is not output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the skid control ECU (brake actuator assembly) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.INSPECT BATTERY

NG

CONNECT CONNECTOR TO BRAKE ACTUATOR ASSEMBLY CORRECTLY

3.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)

NG

4.CHECK TERMINAL VOLTAGE (IG1 TERMINAL)
a.
C364797C06
1.542,0.104 1.917,0.333 0.375,0.229 2.906,1.854 2.906,1.375 2.906,1.375 2.5,0.917 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 2.833,1.927 3.281,2.156 0.448,0.229 10 false IG1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A42-12 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (IG1 CIRCUIT)

5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C364797C03
1.542,0.104 1.917,0.333 0.375,0.229 0.271,1.677 0.271,1.521 0.271,1.521 0.698,1.219 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 0.094,1.75 0.625,1.958 0.531,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK (w/ Rear Differential Lock)
OK (w/o Rear Differential Lock)
NG



OK (w/ Rear Differential Lock)

6.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)

OK (w/o Rear Differential Lock)

7.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

6.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)
a.

Turn the ignition switch off.


b.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


c.

Turn the ignition switch to ON.


d.

Rear differential switch ON.


e.

Disconnect the A42 skid control ECU (brake actuator assembly) connector.


f.
C363591C04
1.521,0.125 1.917,0.354 0.396,0.229 2.271,0.875 2.344,0.24 2.344,0.24 2.542,0.24 true 1.594,0.156 1.906,0.354 0.313,0.198 10 false A42 2.583,0.156 2.979,0.354 0.396,0.198 10 false EXI3
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A42-11 (EXI3) - Body ground
·

Ignition switch ON

·

Rear differential switch ON


Below 1 Ω


Result:
Proceed to
OK
NG




OK

7.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

8.CHECK HARNESS AND CONNECTOR (EXI3/FSW+ TERMINAL CIRCUIT)
7.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.


f.

According to the display on the GTS, read the Data List.


Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light OFF or ON OFF: Warning light off
ON: Warning light on
-
Chassis > ABS/VSC/TRC > Data List
Tester Display
ABS Warning Light
50003 105 51
g.

Check the GTS display condition of the ABS warning light.

Result:
Proceed to
Display of the Data List remains OFF
Display of the Data List remains ON




Display of the Data List remains OFF

Display of the Data List remains ON

8.CHECK HARNESS AND CONNECTOR (EXI3/FSW+ TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the L25 combination meter assembly connector.


c.

Disconnect the V1 rear differential lock position switch (No. 4 transfer indicator switch) connector.


d.

Disconnect the I8 differential lock ECU (No. 2 4 wheel drive control ECU) connector.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-11 (EXI3) - V1-2 Always Below 1 Ω
A42-11 (EXI3) or V1-2 - Body ground Always 10 kΩ or higher
A42-11 (EXI3) - L25-17 (RRSW) Always Below 1 Ω
A42-11 (EXI3) or L25-17 (RRSW) - Body ground Always 10 kΩ or higher
A42-11 (EXI3) - I8-2 (RLP) Always Below 1 Ω
A42-11 (EXI3) or I8-2 (RLP) - Body ground Always 10 kΩ or higher
A42-23 (FSW+) - V1-2 Always Below 1 Ω
A42-23 (FSW+) or V1-2 - Body ground Always 10 kΩ or higher
A42-23 (FSW+) - L25-17 (RRSW) Always Below 1 Ω
A42-23 (FSW+) or L25-17 (RRSW) - Body ground Always 10 kΩ or higher
A42-23 (FSW+) - I8-2 (RLP) Always Below 1 Ω
A42-23 (FSW+) or I8-2 (RLP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

9.INSPECT NO. 4 TRANSFER INDICATOR SWITCH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.INSPECT NO. 4 TRANSFER INDICATOR SWITCH
a.

Remove the rear differential lock position switch (No. 4 transfer indicator switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>REMOVAL


b.

Inspect the rear differential lock position switch (No. 4 transfer indicator switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 4 WHEEL DRIVE CONTROL ECU

NG