Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › 2016.08–2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM  C1241  Low Power Supply Voltage Malfunction  


DESCRIPTION

If a malfunction is detected in the power supply circuit, the skid control ECU (brake actuator assembly) stores this DTC and the fail-safe function prohibits ABS operation.

This DTC is stored when the +BS terminal voltage deviates from the DTC detection condition due to a malfunction in the power supply or charging circuit such as the battery or generator circuit, etc.

The DTC is canceled when the +BS terminal voltage returns to normal.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1241 Low Power Supply Voltage Malfunction Any of the following is detected:
1.

When vehicle speed is 3 km/h (2 mph) or more, +BS terminal voltage is continuously below 9.5 V for 10 seconds or more.

2.

When solenoid relay is on, +BS terminal voltage is below 9.5 V and relay contact is off for 0.22 seconds or more.

3.

When +BS terminal voltage is below 9.5 V, power supply voltage of vehicle speed sensor is continuously low for 60 seconds or more.

4.

When fail-safe motor relay is on and +BS terminal voltage is below 9.5 V, fail-safe motor relay overcurrent continues for 0.05 seconds or more.


·

ABS SOL fuse

·

Battery

·

Charging system

·

Wire harness or connector

·

Skid control ECU (Brake actuator assembly)



WIRING DIAGRAM

C283800E20
2.167,0.844 3.219,1.125 1.052,0.281 10 false from Battery 3.573,1.063 4.229,1.26 0.656,0.198 10 false ABS SOL 5.563,0.865 6.021,1.063 0.458,0.198 10 false +BS 5.281,0.729 5.594,0.927 0.313,0.198 10 false 38 5.24,2.906 5.469,3.156 0.229,0.25 10 false 25 5.573,3.042 6.188,3.24 0.615,0.198 10 false GND1 4.802,3.531 5.26,3.729 0.458,0.198 10 false A42 4.802,3.729 6.896,4.052 2.094,0.323 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the skid control ECU (brake actuator assembly), perform zero point calibration and store system information.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>CALIBRATION

·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.



PROCEDURE

1.INSPECT BATTERY
a.

Check the battery voltage.

Standard voltage:

11 to 14 V


Result:
Proceed to
OK
NG




OK

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)

NG

2.CHECK TERMINAL VOLTAGE (+BS TERMINAL)
a.

Turn the ignition switch off.


b.

Make sure that there is no looseness in the locking part and connecting part of the connectors.


c.
C364797C02
1.542,0.104 1.917,0.333 0.375,0.229 3.208,1.823 3.208,1.677 3.208,1.677 2.802,1.219 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 3.042,1.885 3.417,2.094 0.375,0.208 10 false +BS
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Disconnect the A42 skid control ECU (brake actuator assembly) connector.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A42-38 (+BS) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (+BS CIRCUIT)

3.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C364797C03
1.542,0.104 1.917,0.333 0.375,0.229 0.271,1.677 0.271,1.521 0.271,1.521 0.698,1.219 true 0.104,0.063 0.417,0.26 0.313,0.198 10 false *a 1.604,0.125 1.917,0.323 0.313,0.198 10 false A42 0.094,1.75 0.625,1.958 0.531,0.208 10 false GND1
*a Front view of wire harness connector
(to Skid Control ECU [Brake Actuator Assembly])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A42-25 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.RECONFIRM DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)

4.RECONFIRM DTC
a.

Reconnect the A42 skid control ECU (brake actuator assembly) connector.



c.

Turn the ignition switch off.


d.

Start the engine.


e.

Drive the vehicle at a speed of 20 km/h (12 mph) or more for 30 seconds or more.


f.

Check if the same DTC is recorded.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If troubleshooting has been carried out according to the Problem Symptoms Table, refer back to the table and proceed to the next step.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>PROBLEM SYMPTOMS TABLE



Result:
Proceed to
DTC C1241 is not output
DTC C1241 is output



DTC C1241 is not output

DTC C1241 is output