Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2017.01
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM J

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  SRS Warning Light Remains ON  


DESCRIPTION

w/o VSC:

The SRS warning light is located on the combination meter assembly. When the ignition switch is turned from off to ON, the SRS warning light illuminates. If the SRS is normal, the SRS warning light turns off automatically after approximately 6 seconds. If there is a malfunction in the SRS, the SRS warning light remains illuminated even after approximately 6 seconds have passed. When terminals TC and CG of the DLC3 are connected, the DTCs are communicated through SRS warning light blinking patterns.


w/ VSC:

The SRS warning light is located in the combination meter assembly.

When the SRS is normal, the SRS warning light comes on for approximately 6 seconds after the ignition switch is turned from off on (IG), and then goes off automatically.

If there is a malfunction in the SRS, the SRS warning light comes on to inform the driver of a problem.

When terminals TC and CG of the DLC3 are connected, DTCs are output by the blinking of the SRS warning light.

The SRS is equipped with a voltage-increase circuit (DC-DC converter) in the airbag sensor assembly in case the source voltage drops.

When the battery voltage drops, the voltage-increase circuit (DC-DC converter) functions to increase the voltage of the SRS to normal voltage.

A malfunction in this circuit is not recorded in the airbag sensor assembly. The SRS warning light automatically goes off when the source voltage returns to normal.

The signal to illuminate the SRS warning light is transmitted from the airbag sensor assembly to the combination meter assembly through the CAN communication system.


WIRING DIAGRAM

C363916E01
0.271,0.75 1.042,1.083 0.771,0.333 10 false from Ignition Switch 2.156,1.052 2.594,1.365 0.438,0.313 10 false IGN 6.146,0.885 7.156,1.198 1.01,0.313 10 false IG2 6.146,2.24 7.156,2.552 1.01,0.313 10 false LA*1 4.979,3.052 5.99,3.365 1.01,0.313 10 false *2 6.146,3.677 7.156,3.99 1.01,0.313 10 false E1 6.146,4.281 7.156,4.594 1.01,0.313 10 false E2 3.188,2.677 7.156,2.875 3.969,0.198 10 false B 3.625,2.25 4.635,2.563 1.01,0.313 10 false A/B*1 3.188,3.292 7.156,3.49 3.969,0.198 10 false B 3.188,4.24 7.156,4.438 3.969,0.198 10 false ES 2.135,2.854 2.688,3.073 0.552,0.219 10 false MET 1.906,3.448 3.542,3.698 1.635,0.25 10 false DOME NO.1 0.198,3.24 1.833,3.49 1.635,0.25 10 false from Battery 2.74,5.688 5.219,5.948 2.479,0.26 10 false Combination Meter Assembly 5.406,5.948 6.99,6.281 1.583,0.333 10 false Airbag Sensor Assembly 0.667,6.25 3.146,6.51 2.479,0.26 10 false : CAN Communication Line 2.771,5.51 7.125,5.708 4.354,0.198 10 false L25 2.854,2.563 7.156,2.833 4.302,0.271 10 false 28 2.854,3.167 7.156,3.438 4.302,0.271 10 false 26 2.854,4.146 7.156,4.417 4.302,0.271 10 false 15 5.427,5.76 6.438,6.073 1.01,0.313 10 false I51 4.146,2.135 5.156,2.448 1.01,0.313 10 false 18 5.854,0.771 6.865,1.083 1.01,0.313 10 false 21 5.865,2.146 6.875,2.458 1.01,0.313 10 false 11 5.865,3.563 6.875,3.875 1.01,0.313 10 false 25 5.875,4.156 6.885,4.469 1.01,0.313 10 false 26 0.313,5.094 7.156,5.344 6.844,0.25 10 false *1: w/o VSC 0.313,5.406 7.156,5.656 6.844,0.25 10 false *2: w/ VSC

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.*

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

When replacing the combination meter assembly, make sure to replace it with a new one.



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle condition.


Result:
Result Proceed to
w/ VSC A
w/o VSC B



A

2.CHECK CAN COMMUNICATION SYSTEM

B

3.CHECK BATTERY
2.CHECK CAN COMMUNICATION SYSTEM
a.

Check if a CAN communication DTC is output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM(w/ VSC)>DIAGNOSIS SYSTEM

Result:
Proceed to
DTCs are output
DTC is not output




DTCs are output

DTC is not output

3.CHECK BATTERY
3.CHECK BATTERY
a.

Measure the voltage of the battery.

Standard voltage:

11 to 14 V


HINT:

If the voltage is below 11 V, recharge or replace the battery before proceeding.



Result:
Proceed to
OK
NG



OK

4.CHECK CONNECTION OF CONNECTORS

NG

RECHARGE OR REPLACE BATTERY

4.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and combination meter assembly.

OK:

The connectors are properly connected.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)

NG

CONNECT CONNECTORS PROPERLY

5.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the connectors from the airbag sensor assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Operate all the components of the electrical system (defogger, wipers, headlights, heater blower, etc.).


C198548C45
0.417,0.729 0.833,0.979 0.417,0.25 1.24,1.906 1.583,1.375 true 2.063,1.865 1.729,1.375 true 2.198,1.354 2.615,1.354 true 0.156,0.073 0.479,0.375 0.323,0.302 10 false *a 0.5,0.781 0.938,1.104 0.438,0.323 10 false I51 1.052,1.875 1.417,2.167 0.365,0.292 10 false E2 2.104,1.875 2.427,2.177 0.323,0.302 10 false E1 2.677,1.271 3,1.573 0.323,0.302 10 false IG2
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-21 (IG2) - Body ground Ignition switch ON 11 to 14 V



f.

Turn the ignition switch off.


g.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-25 (E1) - Body ground Always Below 1 Ω
I51-26 (E2) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)

NG

REPLACE HARNESS AND CONNECTOR

6.CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - BATTERY AND BODY GROUND)
a.

Disconnect the connector from the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


C212427C04
1.542,0.677 1.906,0.948 0.365,0.271 0.531,1.927 0.698,1.927 0.698,1.927 1.031,1.656 true 2.594,2.031 2.406,2.031 2.406,2.031 2.219,1.677 true 2.74,1.865 2.552,1.865 2.552,1.865 2.417,1.656 true 0.125,0.208 0.438,0.365 0.313,0.156 10 false *a 1.594,0.729 1.906,0.885 0.313,0.156 10 false L25 2.635,1.948 2.948,2.104 0.313,0.156 10 false B 0.26,1.854 0.573,2.01 0.313,0.156 10 false ES 2.76,1.802 3.073,1.958 0.313,0.156 10 false B
*a Front view of wire harness connector
(to Combination Meter Assembly)


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L25-28 (B) - Body ground Ignition switch ON 11 to 14 V
L25-26 (B) - Body ground Always 11 to 14 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L25-15 (ES) - Body ground Always Below 1 Ω



Result:
Proceed to
OK (w/ VSC)
OK (w/o VSC)
NG



OK (w/ VSC)

9.CHECK SRS WARNING LIGHT

OK (w/o VSC)

7.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - COMBINATION METER ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (AIRBAG SENSOR ASSEMBLY - COMBINATION METER ASSEMBLY)
a.
C364687C01
0.448,1.177 0.865,1.458 0.417,0.281 0.333,2.948 0.75,3.229 0.417,0.281 2.646,1.802 2.49,1.802 2.49,1.802 2.219,1.438 true 1.135,4.198 1.323,4.198 1.323,4.198 1.385,3.667 true 0.573,1.219 1.031,1.417 0.458,0.198 10 false I51 0.417,3 0.875,3.198 0.458,0.198 10 false L25 2.719,1.698 3.177,1.896 0.458,0.198 10 false LA 0.854,4.104 1.313,4.302 0.458,0.198 10 false A/B 0.167,0.104 0.625,0.302 0.458,0.198 10 false *a 0.167,2.625 0.625,2.823 0.458,0.198 10 false *b
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)
*b Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I51-11 (LA) - L25-18 (A/B) Always Below 1 Ω
I51-11 (LA) - Body ground Always 10 MΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK COMBINATION METER ASSEMBLY

NG

REPLACE HARNESS AND CONNECTOR

8.CHECK COMBINATION METER ASSEMBLY
a.

Connect the connector to the combination meter assembly.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 second.


c.

Turn the ignition switch to ON.


d.
C198548C46
0.417,0.719 0.833,0.969 0.417,0.25 2.188,1.167 2.51,1.479 2.51,1.479 2.698,1.479 true 0.146,0.073 0.469,0.375 0.323,0.302 10 false *a 0.49,0.771 0.813,1.073 0.323,0.302 10 false I51 2.75,1.406 3.073,1.708 0.323,0.302 10 false LA
*a Rear view of wire harness connector
(to Airbag Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I51-11 (LA) - Body ground Ignition switch ON 11 to 14 V



e.

Turn the ignition switch to OFF.


Result:
Proceed to
OK
NG



OK

9.CHECK SRS WARNING LIGHT

NG

REPLACE COMBINATION METER ASSEMBLY

9.CHECK SRS WARNING LIGHT
a.

w/ VSC:

Connect the connector to the combination meter assembly.


b.

Turn the ignition switch to ON.


c.

Check the SRS warning light condition.

NOTICE:

Make sure that nobody is in the vehicle.


OK:

After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.



Result:
Proceed to
OK
NG



OK

10.REPLACE AIRBAG SENSOR ASSEMBLY

NG

REPLACE COMBINATION METER ASSEMBLY

10.REPLACE AIRBAG SENSOR ASSEMBLY
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.



d.

Check the SRS warning light condition.

OK:

SRS warning light illuminates normally.



Result:
Proceed to
OK
NG



OK

END (AIRBAG SENSOR ASSEMBLY WAS DEFECTIVE)

NG

REPLACE COMBINATION METER ASSEMBLY