Refer to "SRS Warning Light Remains ON".
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SRS Warning Light Remains ON
Refer to "SRS Warning Light Remains ON".
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>SRS Warning Light Remains ON
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
After replacing the airbag sensor assembly, refer to initialization.*
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION
*: w/ VSC
Inspect the fuses for circuits related to this system before performing the following procedure.
When replacing the combination meter assembly, make sure to replace it with a new one.
Measure the battery voltage.
11 to 14 V
It may be possible to tell whether the battery is discharged by operating the horn.
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connector is properly connected to the combination meter assembly.
| Proceed to |
|---|
| The connector is properly connected |
| The connector is not properly connected |
The connector is properly connected
The connector is not properly connected
| *a | Front view of wire harness connector (to Combination Meter Assembly) |
Disconnect the connector from the combination meter assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| L25-28 (B) - Body ground | Ignition switch to ON | 11 to 14 V |
| L25-26 (B) - Body ground | Always | 11 to 14 V |
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L25-15 (ES) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Connect the connector to the combination meter assembly.
Disconnect the connector from the airbag sensor assembly.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON.
Check the SRS warning light condition.
After the primary check period, the SRS warning light goes off for approximately 10 seconds and then remains on.
The primary check period is approximately 6 seconds after the ignition switch is turned to ON.
| Proceed to |
|---|
| OK |
| NG (w/ VSC) |
| NG (w/o VSC) |
OK
NG (w/ VSC)
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
NG (w/o VSC)
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Replace the airbag sensor assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>REMOVAL
Check the SRS warning light condition.
SRS warning light illuminates normally.
| Proceed to |
|---|
| OK |
| NG |
OK
NG