Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1625/22  Side Airbag Sensor LH Circuit Malfunction  


DESCRIPTION

The door side airbag sensor LH consists of a diagnostic circuit and sideal deceleration sensor, etc.

If the airbag sensor assembly receives signals from the sideal deceleration sensor, it determines whether the SRS should be activated.

DTC B1625/22 is stored when a malfunction is detected in the door side airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1625/22 Side Airbag Sensor LH Circuit Malfunction Either condition is met:
·

A door side airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Door side airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C305104E16
1.24,0.917 1.698,1.115 0.458,0.198 10 false BBL+ 1.271,2.083 1.729,2.281 0.458,0.198 10 false BBL- 1.688,0.781 2.146,0.979 0.458,0.198 10 false 2 1.677,1.938 2.135,2.135 0.458,0.198 10 false 1 5.385,0.781 5.844,0.979 0.458,0.198 10 false 8 5.323,1.979 5.781,2.177 0.458,0.198 10 false 15 0.354,2.813 1.938,3.031 1.583,0.219 10 false S26 5.281,2.792 6.74,3.01 1.458,0.219 10 false S24 0.344,2.958 2.292,3.167 1.948,0.208 10 false Door Side Airbag Sensor LH 5.271,3.01 7.021,3.385 1.75,0.375 10 false Airbag Sensor Assembly 5.615,0.906 7.156,1.167 1.542,0.26 10 false BBL+ 5.615,2.104 7.156,2.365 1.542,0.26 10 false BBL-

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION



PROCEDURE

1.CHECK DOOR SIDE AIRBAG SENSOR LH
a.
C214664C06
0.624,1.525 0.789,1.69 0.166,0.166 10 *1 2.01,1.525 2.176,1.69 0.166,0.166 10 *2
*1 Door Side Airbag Sensor RH
*2 Airbag Sensor Assembly


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Interchange the door side airbag sensor LH with RH and connect the connectors to them.


d.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63

g.

Turn the ignition switch off.


h.

Turn the ignition switch to ON, and wait for at least 60 seconds.


i.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63
Result:
Proceed to
DTC B1625/22 is output
DTC B1620/21 is output
DTC B1620/21 and B1625/22 are not output


HINT:

Codes other than DTC B1620/21 and B1625/22 may be output at this time, but they are not related to this check.



j.

Turn the ignition switch off.


k.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


l.

Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.



DTC B1625/22 is output

DTC B1620/21 is output

DTC B1620/21 and B1625/22 are not output