Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) › from 2016.08
RM25T0E _52 Drivetrain _029907 AXLE AND DIFFERENTIAL _0136709 REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock) A

AXLE AND DIFFERENTIAL  REAR DIFFERENTIAL CARRIER ASSEMBLY(w/ Differential Lock)  REASSEMBLY  


PROCEDURE

Hide 1.INSPECT DIFFERENTIAL SIDE GEAR BACKLASH

a.
C124142

Install the 2 rear No. 1 differential side gear thrust washers to the 2 rear differential side gears.


b.

Install the 4 rear differential pinion thrust washers to the 4 rear differential pinions.


c.
C161882

Install the 2 rear differential side gears into the differential case.


d.

Install the rear differential pinion shaft holder into the differential case.


e.

Install the 4 rear differential pinions and 4 rear differential pinion thrust washers.


f.

Align the holes of the differential case and pinion shaft, and install the 2 rear No. 1 differential pinion shafts and rear differential pinion shaft.


g.

Install the rear differential side gear to the differential cover.


h.

Align the matchmarks and temporarily install the 5 bolts and 3 pinion shaft pins.


i.

Using a T10 "TORX" socket, tighten the 5 bolts and 3 pinion shaft pins.

Torque:
57.9 N*m (590 kgf*cm, 43 ft.*lbf)


j.
C161883

Using a dial indicator, while holding the rear differential side gear, measure the backlash.

Standard backlash:

0.02 to 0.15 mm (0.00079 to 0.00590 in.)


If the backlash is not within the specification, install a thrust washer of a different thickness.

HINT:
·

Make sure the washers on both sides are the same size.

·

Measure at all 4 locations.

·

Apply hypoid gear oil to each sliding surface and rotating part.



Standard Thrust Washers Thickness:
Thickness Thickness
1.53 to 1.57 mm (0.0603 to 0.0618 in.) 1.83 to 1.87 mm (0.0721 to 0.0736 in.)
1.58 to 1.62 mm (0.0623 to 0.0637 in.) 1.88 to 1.92 mm (0.0741 to 0.0755 in.)
1.63 to 1.67 mm (0.0642 to 0.0657 in.) 1.93 to 1.97 mm (0.0760 to 0.0775 in.)
1.68 to 1.72 mm (0.0662 to 0.0677 in.) 1.98 to 2.02 mm (0.0780 to 0.0795 in.)
1.73 to 1.77 mm (0.0682 to 0.0696 in.) 2.03 to 2.07 mm (0.0800 to 0.0814 in.)
1.78 to 1.82 mm (0.0701 to 0.0716 in.) 2.08 to 2.12 mm (0.0819 to 0.0834 in.)



k.

After measuring the backlash, remove the 5 set bolts and 3 pinion shaft pins.


Hide 2.ASSEMBLE DIFFERENTIAL CASE

a.

Clean the threads of the 5 bolts, 3 pinion shaft pins, differential case and differential cover with non-residue solvent.


b.
C161884C01
0.698,1.156 1.167,1.344 1.167,1.344 0.688,1.229 true 1.25,1.292 1.49,1.5 0.24,0.208 10 true *a
*a Matchmark


Coat the threads of the 5 bolts and 3 pinion shaft pins with adhesive.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



c.

Align the matchmarks, and install the differential case and differential cover.


d.

Using a T10 "TORX" socket, install the 5 bolts and 3 pinion shaft pins.

Torque:
57.9 N*m (590 kgf*cm, 43 ft.*lbf)


Hide 41301A 3.INSTALL REAR DIFFERENTIAL CASE BEARING

a.
C161885N01
0.205,0.515 0.533,0.664 0.329,0.15 10 SST 0.811,0.74 0.574,0.625 false

Differential Cover Side:

Using SST and a press, press in the rear differential case bearing (inner race) on the differential cover.

SST
09550-60010  


b.
C161886N01
0.204,0.404 0.533,0.554 0.329,0.15 10 SST 0.811,0.63 0.573,0.514 false

Ring Gear Side:

Using SST and a press, press in the rear differential case bearing (inner race) on the differential case.

SST
09550-60010  


Hide 4.INSTALL DIFFERENTIAL RING GEAR

a.

Clean the threads of the bolts and differential case with non-residue solvent.


b.

Clean the contact surface of the differential case and differential ring gear.


c.

Heat the differential ring gear to about 100°C (212°F) in boiling water.


d.

Carefully take the differential ring gear out of the boiling water.


e.

After the moisture on the differential ring gear has completely evaporated, quickly install the differential ring gear to the differential case.


f.
C161887C01
0.896,1.49 1.875,1.271 1.875,1.271 0.885,1.385 true 1.938,1.188 2.76,1.344 0.823,0.156 10 false *a
*a Matchmark


Align the matchmarks on the differential ring gear and differential case.


g.

Apply thread lock adhesive to the threads of the 12 set bolts and temporarily install them.

Thread lock:

Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent



h.

After the differential ring gear cools down sufficiently, tighten the set bolts.

Torque:
137 N*m (1397 kgf*cm, 101 ft.*lbf)


Hide 5.INSPECT DIFFERENTIAL RING GEAR

a.

Place the bearing outer races on their respective bearings.

HINT:

Do not interchange the left and right outer races.



b.

Install the assembled plate washers onto the rear differential case bearing (outer race).


c.

Install the differential case onto the differential carrier.

HINT:

If it is difficult to install the differential case onto the differential carrier, replace the plate washer with a thinner one.

However, select a plate washer that allows no clearance between it and the differential carrier.



d.

Align the matchmarks on the bearing caps and differential carrier.


e.

Install and uniformly tighten the 4 bolts a little at a time.


f.
C161871

Using a dial indicator, check the ring gear runout.

Maximum runout:

0.05 mm (0.00197 in.)



g.

Remove the differential case.


Hide 41201B 6.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

a.
C161851N03
1.653,0.715 0.831,0.868 0.831,0.868 1.551,0.993 false 0.464,0.789 0.808,0.992 0.344,0.203 10 SST

Using SST and a press, press in the rear drive pinion front tapered roller bearing (outer race).

SST
09950-60020  (09951-00710)
09950-70010  (09951-07150)


Hide 41201A 7.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.
C162726N03
0.66,0.605 1.036,0.78 0.376,0.175 10 SST 1.722,0.87 1.022,0.727 1.022,0.727 1.639,1.157 false

Using SST and a press, press in the rear drive pinion rear tapered roller bearing (outer race).

SST
09950-60020  (09951-00890)
09950-70010  (09951-07150)


Hide 41201A 8.INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING

a.

Install the rear differential drive pinion plate washer onto the differential drive pinion.

HINT:

First fit a rear differential drive pinion plate washer with the same thickness as the removed rear differential drive pinion plate washer, and then check the tooth contact pattern. Replace the rear differential drive pinion plate washer with one of a different thickness if necessary.



b.
C161852C01
1.896,1.333 2.302,1.156 true 1.51,1.01 1.188,0.781 false 2.375,1.031 2.76,1.219 0.385,0.188 10 false SST 1.042,0.708 1.938,0.917 0.896,0.208 10 false *1
*1 Front Differential Drive Pinion Plate Washer


Using SST and a press, press in the rear drive pinion rear tapered roller bearing (inner race).

SST
09506-35010  


Hide 9.INSPECT DRIVE PINION PRELOAD

a.
C237303

Install the differential drive pinion, rear drive pinion front tapered roller bearing (inner race) and rear differential drive pinion oil slinger.

HINT:

Install the rear differential drive pinion bearing spacer and rear differential carrier oil seal after adjusting the gear contact pattern.



b.
C161853C01
1.458,0.688 0.917,0.552 false 0.531,0.448 0.906,0.615 0.375,0.167 10 false SST 2.813,0.719 3.125,0.917 0.313,0.198 10 false *a 0.521,1.479 0.833,1.677 0.313,0.198 10 false *b
*a Turn
*b Hold


Using SST, install the rear drive pinion companion flange sub-assembly with dust deflector.

SST
09950-30012  (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)


c.
C282254C01
0.573,0.594 0.896,0.594 false 3.052,1.115 3.365,1.313 0.313,0.198 10 false *a 0.281,1.063 0.594,1.26 0.313,0.198 10 false *b 0.281,0.51 0.594,0.708 0.313,0.198 10 false SST
*a Turn
*b Hold


Using SST, hold the rear drive pinion companion flange sub-assembly.

SST
09330-00021  (09330-00030)


d.

Using a 30 mm socket wrench and torque wrench, gradually tighten the rear drive pinion companion flange nut within the adjustment range of the differential drive pinion preload.

Torque:
441 N*m (4497 kgf*cm, 325 ft.*lbf)

or less


NOTICE:
·

As there is no rear differential drive pinion bearing spacer, tighten the rear drive pinion companion flange nut a little at a time. Be careful not to overtighten it.

·

Apply hypoid gear oil LSD to the drive pinion threads and rear drive pinion companion flange nut seat face.




e.
C124126

Using a torque wrench, measure the preload.

Standard Preload (At Starting):
Bearing Preload
New 1.08 to 1.73 N*m (12 to 17 kgf*cm, 10 to 15 in.*lbf)
Reused 0.89 to 1.41 N*m (10 to 14 kgf*cm, 8 to 12 in.*lbf)


HINT:

Measure the total preload after first turning the bearing clockwise and counterclockwise several times to make the bearing smooth.



Hide 41302 10.INSTALL REAR DIFFERENTIAL CASE SUB-ASSEMBLY

a.
C161888

Place the rear differential case bearings (outer race) on their respective bearings.

HINT:

Do not interchange the left and right outer races.



b.

Install the assembled plate washer onto the rear differential case bearing.


c.

Install the differential case onto the differential carrier.


d.
C161889

Using a plastic-faced hammer, tap on the differential ring gear to make sure the differential case is aligned with the differential carrier, and fit the rear differential case bearings and plate washers into the differential carrier.

HINT:

If it is difficult to install the differential case onto the differential carrier, replace the plate washer with a thinner one.

However, select a plate washer that allows no clearance between it and the differential carrier.



Hide 11.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161890

Using a dial indicator, measure the backlash while holding the rear differential case bearing of the differential ring gear side.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)



b.

Select a case cover side plate washer using the backlash as a reference.

Standard Side Plate Washer Thickness:
Mark No. Thickness Mark No. Thickness
01 2.66 to 2.68 mm (0.1048 to 0.1055 in.) 13 3.02 to 3.04 mm (0.1189 to 0.1196 in.)
02 2.69 to 2.71 mm (0.1060 to 0.1066 in.) 14 3.05 to 3.07 mm (0.1201 to 0.1208 in.)
03 2.72 to 2.74 mm (0.1071 to 0.1078 in.) 15 3.08 to 3.10 mm (0.1213 to 0.1220 in.)
04 2.75 to 2.77 mm (0.1083 to 0.1090 in.) 16 3.11 to 3.13 mm (0.1225 to 0.1232 in.)
05 2.78 to 2.80 mm (0.1095 to 0.1102 in.) 17 3.14 to 3.16 mm (0.1237 to 0.1244 in.)
06 2.81 to 2.83 mm (0.1107 to 0.1114 in.) 18 3.17 to 3.19 mm (0.1249 to 0.1255 in.)
07 2.84 to 2.86 mm (0.1119 to 0.1125 in.) 19 3.20 to 3.22 mm (0.1260 to 0.1267 in.)
08 2.87 to 2.89 mm (0.1130 to 0.1137 in.) 20 3.23 to 3.25 mm (0.1272 to 0.1279 in.)
09 2.90 to 2.92 mm (0.1142 to 0.1149 in.) 21 3.26 to 3.28 mm (0.1284 to 0.1291 in.)
10 2.93 to 2.95 mm (0.1154 to 0.1161 in.) 22 3.29 to 3.31 mm (0.1296 to 0.1303 in.)
11 2.96 to 2.98 mm (0.1166 to 0.1173 in.) 23 3.32 to 3.34 mm (0.1308 to 0.1314 in.)
12 2.99 to 3.01 mm (0.1178 to 0.1185 in.) - -



c.
C161892

Select a ring gear teeth side plate washer so that there is no clearance between the outer race and case.


d.
C161893

Remove the 2 plate washers and differential carrier.


e.

Install the plate washer into the lower part of the differential carrier.


f.

Place the plate washer onto the differential case together with the outer races, and install the differential case with the outer races onto the differential carrier.


g.

Using a plastic-faced hammer, tap on the differential ring gear to make sure the differential case is aligned with the differential carrier, and fit the rear differential case bearings and plate washers into the differential carrier.


h.
C161890

Using a dial indicator, measure the differential ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


If the backlash is not within the specification, adjust it by either increasing or decreasing the thickness of washers on both sides by an equal amount.

HINT:

There should be no clearance between the plate washers and case.



i.

Ensure that there is differential ring gear backlash.


Hide 12.ADJUST SIDE BEARING PRELOAD

a.

Remove the differential ring gear side plate washer.


b.
C124163

Using a micrometer, measure the thickness.


c.

Using the backlash as a reference, select a washer that is 0.06 to 0.09 mm (0.00237 to 0.00354 in.) thicker than the removed washer.

HINT:

Select a washer which can be pressed in 2/3 of the full amount with your finger.



d.

Install the selected plate washer.


e.
C161894N01
1.642,1.178 1.219,0.922 false 0.84,0.816 1.142,0.998 0.302,0.182 10 SST

Using a plastic-faced hammer and SST, tap the plate washer so that it fits to the rear differential case bearing.

SST
09504-22012  


f.
C161875C01
1.219,1.354 0.438,1.74 0.438,1.74 1.229,1.427 true 0.26,1.656 0.573,1.854 0.313,0.198 10 false *a
*a Matchmark


Align the matchmarks on the 2 bearing caps and differential carrier.


g.

Install the 4 bearing cap bolts to the specified torque.

Torque:
113 N*m (1152 kgf*cm, 83 ft.*lbf)


h.

Using a dial indicator, adjust the differential ring gear backlash until it is within the specification.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)



Hide 13.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

Standard total preload (at starting):

0.29 to 0.49 N*m (3 to 4 kgf*cm, 3 to 4 in.*lbf) + Standard drive pinion preload



Hide 14.INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION

a.
C161895

Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.


b.

Turn the companion flange in both directions to inspect the ring gear for proper tooth contact.

C247128C02
0.313,0.927 0.625,1.125 0.313,0.198 10 *a 2.563,0.083 2.875,0.281 0.313,0.198 10 *b 4.844,0.063 5.156,0.26 0.313,0.198 10 *c 3.667,1.479 3.979,1.677 0.313,0.198 10 *d 2.656,1.99 2.969,2.188 0.313,0.198 10 *e 4.875,2.042 5.188,2.24 0.313,0.198 10 *f 3.708,3.281 4.021,3.479 0.313,0.198 10 *g
*a Proper Contact *b Heel Contact
*c Face Contact *d Select an adjusting washer that will shift the drive pinion closer to the ring gear (*b, *c)
*e Toe Contact *f Flank Contact
*g Select an adjusting washer that will shift the drive pinion away from the ring gear (*e, *f) - -


C237312C02
2.111,1.755 2.274,1.906 0.163,0.152 10 *1 1.738,1.45 1.738,1.84 1.738,1.84 2.08,1.84 false
*1 Rear Differential Drive Pinion Plate Washer


If the teeth are not contacting properly, use the following table and select a proper washer for correction.

Standard Washer Thickness:
Thickness Thickness
1.04 to 1.06 mm (0.0410 to 0.0417 in.) 1.315 to 1.335 mm (0.0518 to 0.0525 in.)
1.065 to 1.085 mm (0.0420 to 0.0427 in.) 1.34 to 1.36 mm (0.0528 to 0.0535 in.)
1.09 to 1.11 mm (0.0430 to 0.0437 in.) 1.365 to 1.385 mm (0.0538 to 0.0545 in.)
1.115 to 1.135 mm (0.0439 to 0.0446 in.) 1.39 to 1.41 mm (0.0548 to 0.0555 in.)
1.14 to 1.16 mm (0.0449 to 0.0456 in.) 1.415 to 1.435 mm (0.0558 to 0.0564 in.)
1.165 to 1.185 mm (0.0459 to 0.0466 in.) 1.44 to 1.46 mm (0.0567 to 0.0574 in.)
1.19 to 1.21 mm (0.0469 to 0.0476 in.) 1.465 to 1.485 mm (0.0577 to 0.0584 in.)
1.215 to 1.235 mm (0.0479 to 0.0486 in.) 1.49 to 1.51 mm (0.0587 to 0.0594 in.)
1.24 to 1.26 mm (0.0489 to 0.0496 in.) 1.515 to 1.535 mm (0.0597 to 0.0604 in.)
1.265 to 1.285 mm (0.0499 to 0.0505 in.) 1.54 to 1.56 mm (0.0607 to 0.0614 in.)
1.29 to 1.31 mm (0.0508 to 0.0515 in.) -




Hide 41204G 15.REMOVE REAR DRIVE PINION COMPANION FLANGE NUT

Hide 41204 16.REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 41214 17.REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201B 18.REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41231 19.INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER

Hide 41201B 20.INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING

Hide 41214 21.INSTALL REAR DIFFERENTIAL DRIVE PINION OIL SLINGER

Hide 41201C 22.INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL

Hide 41204 23.INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY WITH DUST DEFLECTOR

Hide 25.INSPECT TOTAL PRELOAD

a.
C124126

Using a torque wrench, measure the preload with the teeth of the differential drive pinion and differential ring gear in contact.

Standard total preload (at starting):

0.29 to 0.49 N*m (3 to 4 kgf*cm, 3 to 4 in.*lbf) + Standard drive pinion preload



Hide 26.INSPECT DIFFERENTIAL RING GEAR BACKLASH

a.
C161872

Using a dial indicator, measure the differential ring gear backlash.

Standard backlash:

0.10 to 0.20 mm (0.00394 to 0.00787 in.)


HINT:

Measure at 3 or more positions around the circumference of the differential ring gear.


If the backlash is not as specified, adjust the side bearing preload or repair as necessary.


Hide 41204 27.INSPECT RUNOUT OF REAR DRIVE PINION REAR COMPANION FLANGE SUB-ASSEMBLY

Hide 41204G 28.STAKE REAR DRIVE PINION COMPANION FLANGE NUT

Hide 41450 29.INSTALL DIFFERENTIAL LOCK SHIFT ACTUATOR

a.

Remove any old FIPG material.


b.

Clean the contact surfaces of any residual FIPG material using non-residue solvent.


c.
C161896C01
0.656,0.927 1.24,0.698 1.24,0.698 1.385,0.698 true 1.479,0.625 2.792,0.792 1.313,0.167 10 false *a
*a Seal Packing Diameter: 1 to 2 mm (0.0394 to 0.0787 in.)


Apply seal packing to the differential lock shift actuator.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


HINT:

Install the differential lock shift actuator within 10 minutes after applying seal packing.



d.
C161897

Install the rear differential lock shift fork and differential lock shift actuator to the differential carrier and match the shift fork hole with the shift lock.


e.

Clean the threads of the set bolt and fork shaft with non-residue solvent.


f.
C161898

Coat the threads of the set bolt with adhesive.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent



g.

Install the shift fork shaft set bolt.

Torque:
19.6 N*m (200 kgf*cm, 14 ft.*lbf)


h.

Engage the rear differential lock sleeve with the dog clutch of the differential case.


i.
C161873

Install the 4 bolts.

Torque:
23.5 N*m (240 kgf*cm, 17 ft.*lbf)


Hide 41456 30.INSTALL REAR DIFFERENTIAL LOCK COVER

a.

Remove any old FIPG material.


b.

Clean the contact surfaces of any residual FIPG material using non-residue solvent.


c.
C161900C01
1.323,1.104 1.615,1.198 true 1.667,1.135 2.979,1.302 1.313,0.167 10 false *a
*a Seal Packing Diameter: 1 to 2 mm (0.0394 to 0.0787 in.)


Apply seal packing to the rear differential lock cover.

Seal packing:

Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent


HINT:

Install the rear differential lock cover within 10 minutes after applying seal packing.



d.
C311223

Install the 3 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 84222D 31.INSTALL NO. 4 TRANSFER INDICATOR SWITCH

a.
C311225

Install a new gasket and the No. 4 transfer indicator switch.

Torque:
40.2 N*m (410 kgf*cm, 30 ft.*lbf)