| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Memory |
|---|---|---|---|---|
| B1500 | Fuel Sender Open Detected | Both conditions are met:
·
The voltage at the IG power supply terminal of the combination meter assembly is between 9.5 and 11.5 V.
·
Average input signal of fuel sender gauge is 4.85 V or more or 0.15 V or less. |
·
Fuel sender gauge assembly
·
Harness or connector
·
Combination meter assembly |
X |
Be careful of flames.
Using the GTS, read the Data List.
Click hereVehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Fuel Input | Fuel input | Min.: 0, Max.: 127.5 | Current fuel level displayed | Unit: Liter |
| Tester Display |
|---|
| Fuel Input |
Fuel amount value displayed on the GTS is almost the same as the needle indication.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the L26 combination meter assembly connector.
Disconnect the C97*1 or T19*2 fuel sender gauge assembly connector.
*1: for 90 L Tank Carried in Middle
*2: for 130 L Tank
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L26-7 (FV) - C97-1 (FV) | Always | Below 1 Ω |
| L26-5 (FE) - C97-3 (FE) | Always | Below 1 Ω |
| L26-10 (FR) - C97-2 (FR) | Always | Below 1 Ω |
| L26-7 (FV) or C97-1 (FV) - Body ground | Always | 10 kΩ or higher |
| L26-5 (FE) or C97-3 (FE) - Body ground | Always | 10 kΩ or higher |
| L26-10 (FR) or C97-2 (FR) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L26-7 (FV) - T19-2 (FV) | Always | Below 1 Ω |
| L26-5 (FE) - T19-3 (FE) | Always | Below 1 Ω |
| L26-10 (FR) - T19-1 (FR) | Always | Below 1 Ω |
| L26-7 (FV) or T19-2 (FV) - Body ground | Always | 10 kΩ or higher |
| L26-5 (FE) or T19-3 (FE) - Body ground | Always | 10 kΩ or higher |
| L26-10 (FR) or T19-1 (FR) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the fuel sender gauge assembly.
for Single Tank Type and 90 L Tank Carried in Middle:
for 130 L Tank:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY(for 130 L Tank)>REMOVAL
Inspect the fuel sender gauge assembly.
for Single Tank Type and 90 L Tank Carried in Middle:
for 130 L Tank:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY(for 130 L Tank)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for Single Tank Type and 90 L Tank Carried in Middle:
for 130 L Tank:
Click hereEngine / Hybrid System>1VD-FTV (FUEL)>FUEL SENDER GAUGE ASSEMBLY(for 130 L Tank)>REMOVAL