Wear protective gloves when removing the exhaust pipe.
The exhaust pipe is extremely hot immediately after the engine has stopped.
Confirm that the exhaust pipe has cooled down before removing it.
17430 1.REMOVE TAILPIPE ASSEMBLY
Remove the 3 bolts and 3 nuts.
Remove the 4 nuts from the 2 exhaust pipe support cushions. Then remove the tailpipe assembly.
Remove the 4 nuts and 2 exhaust pipe support cushions from the tailpipe assembly.
Remove the gasket from the center exhaust pipe assembly.
17420 2.REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Model Code #J78 Series)
Remove the 2 bolts and 2 nuts.
Remove the 2 nuts from the exhaust pipe support cushion. Then remove the center exhaust pipe assembly.
Remove the 2 nuts and exhaust pipe support cushion from the center exhaust pipe assembly.
| *1 | Muffler Clamp Bracket |
| *2 | Exhaust Pipe Support Cushion |
| *3 | Support Bracket |
Remove the 2 nuts and muffler clamp bracket.
Remove the 2 nuts and exhaust pipe support cushion from the support bracket.
Remove the gasket from the front exhaust pipe assembly.
17420 3.REMOVE CENTER EXHAUST PIPE ASSEMBLY (for Model Code #J79 Series)
except Double Cab w/o DPF:
Remove the 2 bolts and 2 nuts.
Remove the 2 nuts from the exhaust pipe support cushion. Then remove the center exhaust pipe assembly.
Remove the 2 nuts and exhaust pipe support cushion from the center exhaust pipe assembly.
except Double Cab w/ DPF:
Remove the 2 nuts and center exhaust pipe assembly.
for Double Cab:
Remove the 2 nuts and center exhaust pipe assembly.
| *1 | Muffler Clamp Bracket |
| *2 | Exhaust Pipe Support Cushion |
| *3 | Support Bracket |
Remove the 2 nuts and muffler clamp bracket.
Remove the 2 nuts and exhaust pipe support cushion from the support bracket.
Remove the gasket from the front exhaust pipe assembly.
51447C 4.REMOVE TRANSFER CASE PROTECTOR
5.SUPPORT MANUAL TRANSMISSION WITH TRANSFER
51203 6.REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
17410 7.REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/o DPF)
for Double Cab:
Remove the 2 nuts from the exhaust pipe support cushion.
Remove the 2 bolts, 2 compression springs and front exhaust pipe assembly.
for Double Cab:
Remove the 2 nuts and exhaust pipe support cushion from the front exhaust pipe assembly.
18421C 8.REMOVE CENTER CONVERTER PROTECTOR STAY (w/o DPF)
Remove the 3 bolts and center converter protector stay.
18450A 9.REMOVE MONOLITHIC CONVERTER ASSEMBLY (w/o DPF)
Remove the 3 nuts, monolithic converter assembly and gasket.
Remove the gasket from the monolithic converter assembly.
18431 10.REMOVE UPPER CATALYTIC CONVERTER INSULATOR (w/o DPF)
Remove the 2 bolts, nut and upper catalytic converter insulator.
89467B 11.REMOVE AIR FUEL RATIO SENSOR (w/ DPF)
17402 12.REMOVE FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY (w/ DPF)
for Model Code #J78 Series:
Remove the 2 bolts and 2 compression springs. Then remove the front No. 2 exhaust pipe assembly.
Remove the 2 bolts, 2 nuts and exhaust pipe damper from the front No. 2 exhaust pipe assembly.
for Model Code #J79 Series:
Remove the 2 bolts and 2 compression springs.
Remove the 2 nuts from the exhaust pipe support cushion. Then remove the front No. 2 exhaust pipe sub-assembly.
Remove the 2 nuts and exhaust pipe support cushion from the front No. 2 exhaust pipe sub-assembly.
89425 13.REMOVE EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
89425A 14.REMOVE NO. 2 EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
89425B 15.REMOVE NO. 3 EXHAUST GAS TEMPERATURE SENSOR (w/ DPF)
17410 16.REMOVE FRONT EXHAUST PIPE ASSEMBLY (w/ DPF)
Disconnect the 2 air hoses front exhaust pipe assembly.
Remove the 4 bolts from the No. 1 exhaust pipe support.
Remove the 2 bolts from the No. 2 frame crossmember sub-assembly.
Remove the 3 nuts, front exhaust pipe assembly and gasket.
Remove the gasket from the front exhaust pipe assembly.