Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1603/83  Front Satellite Sensor Bus RH Initialization Incomplete  B1612/83  Lost Communication with Front Airbag Sensor RH  B1613/83  Front Airbag Sensor RH Initialization Incomplete  


DESCRIPTION

The front airbag sensor RH circuit consists of the airbag sensor assembly and front airbag sensor RH.

The front airbag sensor RH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1603/83, B1612/83 or B1613/83 is stored when a malfunction is detected in the front airbag sensor RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1603/83 Front Satellite Sensor Bus RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Front airbag sensor RH

·

Airbag sensor assembly


B1612/83 Lost Communication with Front Airbag Sensor RH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Front airbag sensor RH

·

Airbag sensor assembly


B1613/83 Front Airbag Sensor RH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor RH circuit for 2 seconds.

·

A front airbag sensor RH malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Front airbag sensor RH

·

Airbag sensor assembly



WIRING DIAGRAM

C305104E03
1.281,0.917 1.74,1.115 0.458,0.198 10 false +SR 1.365,2.083 1.823,2.281 0.458,0.198 10 false -SR 5.604,0.917 6.063,1.115 0.458,0.198 10 false +SR 5.594,2.073 6.052,2.271 0.458,0.198 10 false -SR 1.688,0.781 2.146,0.979 0.458,0.198 10 false 2 1.677,1.938 2.135,2.135 0.458,0.198 10 false 1 5.333,0.781 5.792,0.979 0.458,0.198 10 false 29 5.323,1.979 5.781,2.177 0.458,0.198 10 false 27 0.354,2.813 1.938,3.031 1.583,0.219 10 false I52 5.281,2.792 6.74,3.01 1.458,0.219 10 false I51 0.344,2.969 1.927,3.188 1.583,0.219 10 false Front Airbag Sensor RH 5.271,3.01 7.021,3.385 1.75,0.375 10 false Airbag Sensor Assembly

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.*

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor RH.

Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected




The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor RH.


b.
C208244C20
0.375,1.344 0.573,1.51 0.198,0.167 10 false *1 2.156,1.76 2.354,1.927 0.198,0.167 10 false *2 1.531,0.49 1.729,0.656 0.198,0.167 10 false *3
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly
*3 Cowl Wire


Check that the connectors (on the airbag sensor assembly side and front airbag sensor RH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK COWL WIRE

The connectors are deformed or damaged

REPLACE COWL WIRE

3.CHECK COWL WIRE
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C305105C03
2.854,0.646 3.229,0.875 0.375,0.229 5.146,0.646 5.521,0.875 0.375,0.229 3.344,1.26 3.708,0.906 true 4.198,1.281 3.885,0.906 true 5.458,1.188 5.948,0.958 true 6.115,0.948 6.677,1.281 true 5.615,1.625 5.771,1.51 true 0.552,1 0.865,1.156 0.313,0.156 10 false *1 1.906,1.24 2.219,1.396 0.313,0.156 10 false *2 1.188,0.406 1.5,0.563 0.313,0.156 10 false *3 4.396,0.75 4.708,0.906 0.313,0.156 10 false *4 6.875,0.656 7.125,0.833 0.25,0.177 10 false *5 3.771,0.135 4.083,0.292 0.313,0.156 10 false *a 6.208,0.104 6.521,0.26 0.313,0.156 10 false *b 0.635,0.625 0.948,0.781 0.313,0.156 10 false D 1.042,0.844 1.188,1 0.146,0.156 10 false C 1.781,0.615 1.927,0.771 0.146,0.156 10 false A 1.458,0.844 1.604,1 0.146,0.156 10 false B 2.927,0.677 3.24,0.833 0.313,0.156 10 false I52 3.156,1.302 3.469,1.458 0.313,0.156 10 false -SR 4.115,1.333 4.427,1.49 0.313,0.156 10 false +SR 5.229,0.677 5.583,0.833 0.354,0.156 10 false I51 5.104,1.135 5.417,1.292 0.313,0.156 10 false +SR 6.698,1.302 7.01,1.458 0.313,0.156 10 false -SR 5.438,1.563 5.688,1.74 0.25,0.177 10 false *6
*1 Front Airbag Sensor RH *2 Airbag Sensor Assembly
*3 Cowl Wire *4 Connector C
*5 Connector B *6 Service Wire
*a Front view of wire harness connector
(to Front Airbag Sensor RH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
I52-2 (+SR) - Body ground Ignition switch ON Below 1 V
I52-1 (-SR) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 29 (+SR) and 27 (-SR) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I52-2 (+SR) - I52-1 (-SR) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
I52-2 (+SR) - I52-1 (-SR) Always 1 MΩ or higher
I52-2 (+SR) - Body ground Always 1 MΩ or higher
I52-1 (-SR) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR RH

NG

REPLACE COWL WIRE

4.CHECK FRONT AIRBAG SENSOR RH
a.
C146229C20
1.063,0.979 1.375,1.135 0.313,0.156 10 false *1 2.094,1.323 2.406,1.479 0.313,0.156 10 false *2
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the front airbag sensor RH with LH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
Result:
Result Proceed to
DTC B1603/83, B1612/83 or B1613/83 is output A
DTC B1608/84, B1617/84 or B1618/84 is output B
DTC B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 are not output C


HINT:

Codes other than DTC B1603/83, DTC B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the front airbag sensor LH and RH to their original positions and connect the connectors to them.



A

B

C