Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › 2016.08–2022.09
RM25T0E _58 Vehicle Interior _029929 SUPPLEMENTAL RESTRAINT SYSTEMS _0138307 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1608/84  Front Satellite Sensor Bus LH Initialization Incomplete  B1617/84  Lost Communication with Front Airbag Sensor LH  B1618/84  Front Airbag Sensor LH Initialization Incomplete  


DESCRIPTION

The front airbag sensor LH circuit consists of the airbag sensor assembly and front airbag sensor LH.

The front airbag sensor LH detects impacts to the vehicle and sends signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1608, B1617/84, B1618/84 is stored when a malfunction is detected in the front airbag sensor LH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1608/84 Front Satellite Sensor Bus LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly


B1617/84 Lost Communication with Front Airbag Sensor LH One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly


B1618/84 Front Airbag Sensor LH Initialization Incomplete One of the following conditions is met:
·

The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front airbag sensor LH circuit for 2 seconds.

·

A front airbag sensor LH malfunction.

·

An airbag sensor assembly malfunction.


·

Cowl wire

·

Engine room main wire

·

Front airbag sensor LH

·

Airbag sensor assembly



WIRING DIAGRAM

C279108E26
1.323,0.917 1.688,1.135 0.365,0.219 10 false +SL 1.365,2.083 1.698,2.281 0.333,0.198 10 false -SL 5.594,2.063 5.979,2.24 0.385,0.177 10 false -SL 5.563,0.896 5.958,1.094 0.396,0.198 10 false +SL 3.427,2.292 3.885,2.49 0.458,0.198 10 false -SL 5.531,3.01 7.083,3.24 1.552,0.229 10 false Airbag Sensor Assembly 5.573,2.833 6.031,3.031 0.458,0.198 10 false I51 0.354,2.854 0.708,3.052 0.354,0.198 10 false A13 1.688,1.969 1.917,2.156 0.229,0.188 10 false 1 3.521,0.719 3.781,0.875 0.26,0.156 10 false 1 3.5,1.885 3.729,2.042 0.229,0.156 10 false 2 1.688,0.813 1.917,1 0.229,0.188 10 false 2 3.448,0.917 3.906,1.115 0.458,0.198 10 false AI5 3.458,2.083 3.896,2.281 0.438,0.198 10 false AI5 3.417,1.115 3.875,1.313 0.458,0.198 10 false +SL 5.313,0.771 5.573,0.927 0.26,0.156 10 false 30 5.313,1.958 5.573,2.115 0.26,0.156 10 false 28 0.323,3.021 1.906,3.198 1.583,0.177 10 false Front Airbag Sensor LH

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

·

After replacing the airbag sensor assembly, refer to initialization.*

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION

*: w/ VSC



PROCEDURE

1.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the airbag sensor assembly and front airbag sensor LH.

Result:
Proceed to
The connectors are properly connected
The connectors are not properly connected




The connectors are properly connected

2.CHECK CONNECTORS

The connectors are not properly connected

CONNECT CONNECTORS PROPERLY

2.CHECK CONNECTORS
a.

Disconnect the connectors from the airbag sensor assembly and front airbag sensor LH.


b.
C213959C28
0.604,1.177 0.917,1.333 0.313,0.156 10 false *1 2.594,1.563 2.906,1.719 0.313,0.156 10 false *2
*1 Front Airbag Sensor LH
*2 Airbag Sensor Assembly


Check that the connectors (on the airbag sensor assembly side and front airbag sensor LH side) are not damaged.


Result:
Proceed to
The connectors are not deformed or damaged
The connectors are deformed or damaged



The connectors are not deformed or damaged

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT

The connectors are deformed or damaged

REPLACE HARNESS AND CONNECTOR

3.CHECK FRONT AIRBAG SENSOR LH CIRCUIT
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C305106C06
2.844,0.708 3.188,0.958 0.344,0.25 5.052,0.688 5.396,0.938 0.344,0.25 3.354,1.323 3.708,0.896 true 4.198,1.344 3.896,0.896 true 5.344,1.229 5.813,0.969 true 6.688,1.292 6.021,0.969 true 5.594,1.625 5.75,1.469 true 1.063,0.427 1.375,0.583 0.313,0.156 10 false *6 1.885,1.292 2.198,1.448 0.313,0.156 10 false *2 4.323,0.74 4.635,0.896 0.313,0.156 10 false *3 6.844,0.625 7.031,0.792 0.188,0.167 10 false *4 5.448,1.604 5.76,1.76 0.313,0.156 10 false *5 3.708,0.125 4.021,0.281 0.313,0.156 10 false *a 6.094,0.073 6.406,0.229 0.313,0.156 10 false *b 0.604,0.615 0.823,0.781 0.219,0.167 10 false F 0.896,0.833 1.115,1 0.219,0.167 10 false E 1.156,0.823 1.375,0.99 0.219,0.167 10 false D 1.271,0.823 1.49,0.99 0.219,0.167 10 false C 4.094,1.385 4.604,1.573 0.51,0.188 10 false +SL 1.51,0.823 1.729,0.99 0.219,0.167 10 false B 3.25,1.365 3.635,1.552 0.385,0.188 10 false -SL 1.802,0.615 2.021,0.781 0.219,0.167 10 false A 2.906,0.76 3.344,0.979 0.438,0.219 10 false A13 5.104,0.729 5.542,0.948 0.438,0.219 10 false I51 5.156,1.26 5.667,1.448 0.51,0.188 10 false +SL 6.635,1.333 7.021,1.521 0.385,0.188 10 false -SL 1.302,0.438 1.615,0.594 0.313,0.156 10 false *7 0.531,1 0.844,1.156 0.313,0.156 10 false *1
*1 Front Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Connector E *4 Connector B
*5 Service Wire *6 Engine Room Main Wire
*7 Cowl Wire - -
*a Front view of wire harness connector
(to Front Airbag Sensor LH)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A13-2 (+SL) - Body ground Ignition switch ON Below 1 V
A13-1 (-SL) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (+SL) - A13-1 (-SL) Always Below 1 Ω



h.

Disconnect the service wire from connector B.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A13-2 (+SL) - A13-1 (-SL) Always 1 MΩ or higher
A13-2 (+SL) - Body ground Always 1 MΩ or higher
A13-1 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK FRONT AIRBAG SENSOR LH

NG

5.CHECK COWL WIRE
4.CHECK FRONT AIRBAG SENSOR LH
a.
C212434C01
0.906,0.969 1.219,1.125 0.313,0.156 10 false *1 2.323,1.302 2.635,1.458 0.313,0.156 10 false *2
*1 Front Airbag Sensor RH
*2 Airbag Sensor Assembly


Connect the connectors to the airbag sensor assembly.


b.

Interchange the front airbag sensor LH with RH and connect the connectors to them.


c.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Clear the DTCs stored in memory.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Clear DTCs
50002 63

f.

Turn the ignition switch off.


g.

Turn the ignition switch to ON, and wait for at least 60 seconds.


h.

Check for DTCs.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR

Body Electrical > SRS Airbag > Trouble Codes
50001 63
Result:
Result Proceed to
DTC B1608/84, B1617/84 or B1618/84 is output A
DTC B1603/83, B1612/83 or B1613/83 is output B
DTC B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 are not output C


HINT:

Codes other than DTC B1603/83, B1612/83, B1613/83, B1608/84, B1617/84 and B1618/84 may be output at this time, but they are not related to this check.



i.

Turn the ignition switch off.


j.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


k.

Return the front airbag sensor RH and LH to their original positions and connect the connectors to them.



A

B

C

5.CHECK COWL WIRE
a.

Disconnect the cowl wire connector from the engine room main wire.

C303686C01
2.854,0.604 3.271,0.875 0.417,0.271 4.875,0.615 5.292,0.885 0.417,0.271 5.438,1.615 5.656,1.521 true 3.188,1.323 3.667,0.823 true 4.323,1.333 3.885,0.823 true 5.385,1.146 5.823,0.948 true 6.615,1.281 6.031,0.969 true 0.427,1 0.74,1.156 0.313,0.156 10 false *1 1.885,1.24 2.198,1.396 0.313,0.156 10 false *2 0.885,0.417 1.198,0.573 0.313,0.156 10 false *3 1.333,0.406 1.646,0.563 0.313,0.156 10 false *4 3.719,0.177 4.031,0.333 0.313,0.156 10 false *5 6.188,0.146 6.5,0.302 0.313,0.156 10 false *6 5.271,1.552 5.583,1.708 0.313,0.156 10 false *7 4.24,1.365 4.656,1.667 0.417,0.302 10 false +SL 3.208,0.229 3.521,0.385 0.313,0.156 10 false *a 5.323,0.219 5.635,0.375 0.313,0.156 10 false *b 3.042,1.354 3.458,1.656 0.417,0.302 10 false -SL 0.521,0.604 0.833,0.771 0.313,0.167 10 false F 0.813,0.854 1.125,1.021 0.313,0.167 10 false E 1.083,0.844 1.396,1.01 0.313,0.167 10 false D 1.25,0.844 1.563,1.01 0.313,0.167 10 false C 1.5,0.844 1.813,1.01 0.313,0.167 10 false B 1.76,0.625 2.073,0.792 0.313,0.167 10 false A 2.938,0.667 3.333,0.854 0.396,0.188 10 false AI5 5.188,1.146 5.604,1.448 0.417,0.302 10 false +SL 6.615,1.323 7.031,1.625 0.417,0.302 10 false -SL 4.958,0.667 5.354,0.854 0.396,0.188 10 false I51
*1 Front Airbag Sensor LH *2 Airbag Sensor Assembly
*3 Engine Room Main Wire *4 Cowl Wire
*5 Connector C *6 Connector B
*7 Service Wire - -
*a Front view of wire harness connector
(to Engine Room Main Wire)
*b Rear view of wire harness connector
(to Airbag Sensor Assembly)



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
AI5-1 (+SL) - Body ground Ignition switch ON Below 1 V
AI5-2 (-SL) - Body ground Ignition switch ON Below 1 V



e.

Turn the ignition switch off.


f.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


g.

Using a service wire, connect terminals 30 (+SL) and 28 (-SL) of connector B.

NOTICE:

Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.



h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AI5-1 (+SL) - AI5-2 (-SL) Always Below 1 Ω



i.

Disconnect the service wire from connector B.


j.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
AI5-1 (+SL) - AI5-2 (-SL) Always 1 MΩ or higher
AI5-1 (+SL) - Body ground Always 1 MΩ or higher
AI5-2 (-SL) - Body ground Always 1 MΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE ENGINE ROOM MAIN WIRE

NG

REPLACE COWL WIRE