Home › Engine / Hybrid System › 1VD-FTV (COOLING) › RADIATOR › from 2016.08
RM25T0E _51 Engine / Hybrid System _029897 1VD-FTV COOLING _0136551 RADIATOR A

1VD-FTV COOLING  RADIATOR  INSTALLATION  


PROCEDURE

Hide 16584 1.INSTALL RADIATOR MOUNTING INSULATOR

a.

Install the 2 radiator mounting insulators and 2 collars.


Hide 16400 2.INSTALL RADIATOR ASSEMBLY

a.
A161829C02
2.958,0.646 2.958,0.979 2.958,0.979 3.125,0.979 true 2.25,0.083 2.5,0.083 2.5,0.083 2.844,0.167 true 2.854,0.344 2.854,1.177 2.854,1.177 2.688,1.177 true 3.167,0.906 3.365,1.083 0.198,0.177 10 false *1 2.51,1.083 2.677,1.271 0.167,0.188 10 false *b 2.083,0 2.333,0.167 0.25,0.167 10 false *a
*1 Collar
*a Specified Hole
*b Claw


Place the radiator assembly to the vehicle.

NOTICE:

Do not allow the radiator assembly to interfere with other parts.



b.

Set the collar claws to the specified holes as shown in the illustration.


c.

Install the radiator assembly with the 4 bolts.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 16572D 3.INSTALL NO. 2 RADIATOR HOSE

a.

Install the No. 2 radiator hose and slide the 2 hose clamps to secure the hose.


Hide 16361 4.INSTALL FAN

a.

Install the fan to the fluid coupling assembly with the 4 nuts.

Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)


Hide 16371 5.INSTALL FAN PULLEY

a.

Install the fan pulley.


Hide 16711 6.INSTALL FAN SHROUD

a.

Place the fan shroud together with the fluid coupling fan between the radiator assembly and engine.

NOTICE:

Do not allow the fluid coupling fan to interfere with other parts.



b.

Temporarily install the fluid coupling fan with the 4 nuts, and then tighten the nuts as much as possible by hand.


c.
A164342

Attach the claws of the fan shroud to the radiator assembly as shown in the illustration.


d.

Install the fan shroud with the 3 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


e.

Install the fan and generator V belt.

Click hereEngine / Hybrid System>1VD-FTV (ENGINE MECHANICAL)>DRIVE BELT>INSTALLATION


f.

Tighten the 4 nuts of the fluid coupling fan.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 16470 7.INSTALL RADIATOR RESERVOIR ASSEMBLY

a.

Install the radiator reservoir assembly with the 3 bolts.

Torque:
7.8 N*m (80 kgf*cm, 69 in.*lbf)


b.

Connect the No. 2 water by-pass hose to the water inlet and slide the hose clamp to secure the hose.


c.

Connect the No. 1 water by-pass hose to the radiator assembly and slide the hose clamp to secure the hose.


Hide 17875 8.INSTALL INTAKE AIR CONNECTOR PIPE

a.
A264661C01
0.667,1.875 0.833,1.875 0.833,1.875 0.833,1.542 false 2.5,0.979 2.5,0.625 2.5,0.625 2.688,0.625 false 1.188,0.25 1.5,0.406 0.313,0.156 10 false *a 0.49,1.802 0.802,1.958 0.313,0.156 10 false *1 2.74,0.542 3.052,0.698 0.313,0.156 10 false *2
*1 Intake Air Connector Pipe
*2 No. 3 Intake Air Connector Pipe
*a 6.0 mm (0.236 in.) or less


Connect the intake air connector pipe to the No. 3 intake air connector pipe.

NOTICE:

Push the intake air connector pipe onto the No. 3 intake air connector pipe so that the clearance is 6.0 mm (0.236 in.) or less.



b.
A327364C01
1.083,3 1.25,3 1.25,3 1.521,2.792 true 1.865,2.552 2.177,2.708 0.313,0.156 10 false *a 0.927,2.917 1.24,3.073 0.313,0.156 10 false *b
*a Left Side
*b 90°


Install the intake air connector pipe with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Tighten the hose clamp.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Connect the ventilation hose to the intake air connector pipe and slide the clip to secure the hose.


e.

Attach the wire harness clamp to connect the wire harness to the intake air connector pipe.


f.

Connect the engine coolant temperature sensor connector.


Hide 17805 9.INSTALL INTAKE AIR CONNECTOR SUB-ASSEMBLY

a.
A264661C01
0.667,1.875 0.833,1.875 0.833,1.875 0.833,1.542 false 2.5,0.979 2.5,0.625 2.5,0.625 2.688,0.625 false 1.188,0.25 1.5,0.406 0.313,0.156 10 false *a 0.49,1.802 0.802,1.958 0.313,0.156 10 false *1 2.74,0.542 3.052,0.698 0.313,0.156 10 false *2
*1 Intake Air Connector Pipe
*2 Intake Air Connector Sub-assembly
*a 5.0 mm (0.197 in.) or less


Connect the intake air connector sub-assembly to the intake air connector pipe.

NOTICE:

Push the intake air connector sub-assembly onto the intake air connector pipe so that the clearance is 5.0 mm (0.197 in.) or less.



b.

Install the intake air connector sub-assembly with the 2 bolts.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


c.

Tighten the hose clamp.

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


d.

Attach the 2 wire harness clamps to connect the wire harness to the intake air connector sub-assembly.


e.

Connect the air flow meter connector.


Hide 10.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly with the 2 bolts and nut.

Torque:
18 N*m (184 kgf*cm, 13 ft.*lbf)


Hide 17881 12.INSTALL NO. 1 AIR CLEANER HOSE

a.

Install the No. 1 air cleaner hose and tighten the 2 hose clamps to secure the hose.

Torque:
2.5 N*m (25 kgf*cm, 22 in.*lbf)

HINT:

Connect the No. 1 air cleaner hose with the arrow marks facing upward and pointing toward the engine.



Hide 16571C 13.INSTALL NO. 1 RADIATOR HOSE

a.

Install the No. 1 radiator hose and slide the 2 hose clamps to secure the hose.


Hide 51442 17.INSTALL NO. 2 ENGINE UNDER COVER