Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ANTI-LOCK BRAKE SYSTEM › from 2016.08
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0135612 ANTI-LOCK BRAKE SYSTEM J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ANTI-LOCK BRAKE SYSTEM  ABS Warning Light Remains ON  


DESCRIPTION

When one of the following conditions is met, the ABS warning light remains on:

·

The brake actuator assembly (skid control ECU) connector is disconnected.

·

There is a malfunction in the brake actuator assembly (skid control ECU) internal circuit.

·

There is an open in the harness between the combination meter and the brake actuator assembly (skid control ECU).

·

The anti-lock brake system is defective.

·

w/ Rear Differential Lock:

The rear differential is locked or the rear differential and front differential are locked.


WIRING DIAGRAM

C368227E01
0.458,0.427 1.479,0.74 1.021,0.313 10 false from IG Circuit 1.875,0.323 2.188,0.521 0.313,0.198 10 false 28 2.125,0.313 2.281,0.51 0.156,0.198 10 false B 2.667,0.625 3.125,0.823 0.458,0.198 10 false ABS 4.281,0.271 4.594,0.469 0.313,0.198 10 false LP 4.552,0.313 4.865,0.51 0.313,0.198 10 false 19 3.125,1.25 4.469,1.438 1.344,0.188 10 false Rear Differential Lock 4.021,0.813 4.635,1.01 0.615,0.198 10 false RRSW 4.542,0.927 5,1.125 0.458,0.198 10 false 17* 1.927,1.615 2.385,1.813 0.458,0.198 10 false L25 1.906,1.802 5.885,2 3.979,0.198 10 false Combination Meter Assembly 2.438,2.271 3.354,2.469 0.917,0.198 10 false ECU IG 0.5,2.125 2.792,2.323 2.292,0.198 10 false from IG Circuit 3.021,3.208 3.177,3.406 0.156,0.198 10 false 1 3.823,3.219 3.979,3.417 0.156,0.198 10 false 2 2.615,3.594 2.927,3.792 0.313,0.198 10 false V1 2.594,3.781 4.844,4.24 2.25,0.458 10 false No. 4 Transfer Indicator Switch (Rear Differential Lock Position Switch)* 1.979,4.49 2.438,4.688 0.458,0.198 10 false RLP 2.375,4.479 2.531,4.677 0.156,0.198 10 false 2 0.719,5.146 1.031,5.354 0.313,0.208 10 false I8 0.698,5.354 4.198,5.677 3.5,0.323 10 false No. 2 4 Wheel Drive Control ECU (Differential Lock ECU)* 0.844,5.917 5.125,6.115 4.281,0.198 10 false *: w/ Rear Differential Lock 5.146,4.135 5.604,4.333 0.458,0.198 10 false A20 5.135,4.354 7.073,4.802 1.938,0.448 10 false Brake Actuator Assembly (Skid Control ECU) 5.563,3.208 5.875,3.406 0.313,0.198 10 false 9* 5.844,3.198 6.458,3.396 0.615,0.198 10 false EXI3 5.552,2.01 5.865,2.208 0.313,0.198 10 false 34 5.865,2.104 6.323,2.302 0.458,0.198 10 false IG1 5.646,1.396 5.802,1.594 0.156,0.198 10 false 1 5.833,1.479 6.448,1.677 0.615,0.198 10 false GND1 5.594,0.313 5.906,0.51 0.313,0.198 10 false 21 5.833,0.396 6.146,0.594 0.313,0.198 10 false WA

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

·

Before disconnecting the connector, make sure that there are no problems with the connection.

·

After disconnecting the connector, make sure that the connector case and terminals are not deformed or corroded.



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch off.


b.

Check if DTCs for the ABS are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ANTI-LOCK BRAKE SYSTEM>DTC CHECK / CLEAR

Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
Result:
Proceed to
DTC is not output
DTC is output




DTC is not output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED

DTC is output

2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
a.

Check if the brake actuator assembly (skid control ECU) connector is securely connected.

OK:

The connector is securely connected.



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)

NG

CONNECT CONNECTOR TO ECU CORRECTLY

3.CHECK HARNESS AND CONNECTOR (IG1 TERMINAL)
a.
C260095C19
0.177,0.917 0.51,1.177 0.333,0.26 2.094,1.833 2.302,1.396 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.229,0.969 0.542,1.167 0.313,0.198 10 false A20 1.865,1.792 2.167,2 0.302,0.208 10 false IG1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Disconnect the A20 brake actuator assembly (skid control ECU) connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-34 (IG1) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)
a.

Turn the ignition switch off.


b.
C260095C20
0.219,0.927 0.563,1.156 0.344,0.229 1.115,0.833 1.26,0.146 true 0.052,0.042 0.365,0.198 0.313,0.156 10 false *a 0.281,0.958 0.594,1.156 0.313,0.198 10 false A20 1.292,0.063 1.906,0.26 0.615,0.198 10 false GND1
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-1 (GND1) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION METER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - COMBINATION METER)
a.

Turn the ignition switch off.


b.

Disconnect the L25 combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-21 (WA) - L25-19 (LP) Always Below 1 Ω
A20-21 (WA) or L25-19 (LP) - Body ground Always 10 kΩ or higher


Result:
Proceed to
OK (w/ Rear Differential Lock)
OK (w/o Rear Differential Lock)
NG




OK (w/ Rear Differential Lock)

6.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)

OK (w/o Rear Differential Lock)

9.PERFORM ACTIVE TEST USING GTS (ABS WARNING LIGHT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL)
a.

Turn the ignition switch to ON.


b.
C260095C26
0.177,0.917 0.51,1.177 0.333,0.26 2.104,0.844 2.417,0.188 true 0.24,0.969 0.552,1.167 0.313,0.198 10 false A20 2.479,0.094 2.802,0.302 0.323,0.208 10 false EXI3 0.073,0.052 0.385,0.208 0.313,0.156 10 false *a
*a Front view of wire harness connector
(to Brake Actuator Assembly [Skid Control ECU])


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A20-9 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Result:
Proceed to
Outside of the specified condition
Within the specified condition




Outside of the specified condition

7.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL CIRCUIT)

Within the specified condition

9.PERFORM ACTIVE TEST USING GTS (ABS WARNING LIGHT)
7.CHECK HARNESS AND CONNECTOR (EXI3 TERMINAL CIRCUIT)
a.

Turn the ignition switch off.


b.

Disconnect the V1 No. 4 transfer indicator switch (rear differential lock position switch) connector.


c.

Disconnect the I8 No. 2 4 wheel drive control ECU (differential lock ECU) connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A20-9 (EXI3) - V1-2 Always Below 1 Ω
A20-9 (EXI3) or V1-2 - Body ground Always 10 kΩ or higher
A20-9 (EXI3) - L25-17 (RRSW) Always Below 1 Ω
A20-9 (EXI3) or L25-17 (RRSW) - Body ground Always 10 kΩ or higher
A20-9 (EXI3) - I8-2 (RLP) Always Below 1 Ω
A20-9 (EXI3) or I8-2 (RLP) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.INSPECT NO. 4 TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.INSPECT NO. 4 TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)
a.

Remove the No. 4 transfer indicator switch (rear differential lock position switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>REMOVAL


b.

Inspect the No. 4 transfer indicator switch (rear differential lock position switch).

Click hereDrivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH(w/ Differential Lock)>INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE NO. 2 4 WHEEL DRIVE CONTROL ECU

NG

REPLACE NO. 4 TRANSFER INDICATOR SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH)

9.PERFORM ACTIVE TEST USING GTS (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the brake actuator assembly (skid control ECU) connector.


c.

Connect the combination meter assembly connector.


d.

Connect the GTS to the DLC3.


e.

Turn the ignition switch to ON.


f.

Turn the GTS on.


g.

Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.

Chassis > ABS/VSC/TRC > Active Test
Tester Display Measurement Item Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON / OFF Observe the combination meter.

h.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.

Chassis > ABS/VSC/TRC > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light ON or OFF ON: ABS warning light on
OFF: ABS warning light off
-

Chassis > ABS/VSC/TRC > Active Test
Active Test Display
ABS Warning Light
Data List Display
ABS Warning Light
50004 105 8 51
Result:
Result Proceed to
Data List Display Data List Display When Performing Active Test ON/OFF Operation
ON Does not change between ON and OFF A
Changes between ON and OFF B
OFF Does not change between ON and OFF A
Changes between ON and OFF B



A

B