Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System) › from 2017.01
RM25T0E _54 Brake _029873 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0287798 VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(w/o Pre-collision System)  C1439  Steering Angle Sensor Initialization Incomplete  C1445  Vehicle Driven with Steering Angle Sensor not Initialized  


DESCRIPTION

The skid control ECU (brake actuator assembly) acquires the steering angle sensor zero point every time the ignition switch is turned to ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores the previous zero point.

The steering angle sensor zero point malfunction warning is canceled by turning the ignition switch off.

DTC No. Detection Item DTC Detection Condition Trouble Area
C1439 Steering Angle Sensor Initialization Incomplete After the steering angle sensor zero point calibration is cleared due to, for example, fluctuations in the power source, the steering angle zero point calibration cannot be obtained for 0.048 seconds of continuous driving.
·

Steering angle sensor (Spiral with sensor cable sub-assembly)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)


C1445 Vehicle Driven with Steering Angle Sensor not Initialized Steering angle sensor zero point calibration cannot be obtained when the vehicle is driven without a record of steering angle sensor zero point calibration at a speed of 35 km/h (22 mph) or more for 30 seconds or more without the brake pedal being depressed.
·

Steering angle sensor (Spiral with sensor cable sub-assembly)

·

Yaw rate and acceleration sensor (Airbag sensor assembly)



CAUTION / NOTICE / HINT

NOTICE:

Before proceeding with the inspection, explain to the customer that the output DTC is related to temporary loss of the steering angle zero point calibration, such as when the power voltage drops when the battery is removed, and confirm that this condition occurred.


HINT:
·

When DTC U0073, U0124 or U0126 is output together with DTC C1439 and/or C1445, inspect and repair the trouble areas indicated by DTC U0073, U0124 or U0126 first.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>U0073

·

When the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly) has trouble, DTCs for the steering angle sensor (spiral with sensor cable sub-assembly) may be stored even when the steering angle sensor (spiral with sensor cable sub-assembly) is normal. When DTCs for the speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) are output together with other DTCs for the steering angle sensor (spiral with sensor cable sub-assembly), inspect and repair the speed sensor and yaw rate and acceleration sensor (airbag sensor assembly) first, and then inspect and repair the steering angle sensor (spiral with sensor cable sub-assembly).



PROCEDURE

1.CHECK DTC

Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
b.

Turn the ignition switch off.


c.

Turn the ignition switch to ON again and check that no CAN communication system DTC is output.

for LHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for LHD with VSC)>DIAGNOSIS SYSTEM

for RHD: Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (for RHD with VSC)>DIAGNOSIS SYSTEM


d.

Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left and check that no speed sensor or yaw rate and acceleration sensor DTCs are output.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (w/o Pre-collision System)>DTC CHECK / CLEAR


Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:
·

If there is a malfunction in the speed sensor or the yaw rate and acceleration sensor (airbag sensor assembly), an abnormal value may be output although the steering angle sensor (spiral with sensor cable sub-assembly) is normal.

·

If the speed sensor and the yaw rate and acceleration sensor (airbag sensor assembly) DTCs are output simultaneously, repair the sensors and inspect the steering angle sensor (spiral with sensor cable sub-assembly).

·

If DTC C1439 or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power voltage drops.



Result:
Result Proceed to
DTC is output C1439 and/or C1445 A
Relating to CAN communication system B
Relating to speed sensor or yaw rate and acceleration sensor (airbag sensor assembly) C
DTC is not output D



A

2.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION

B

C

D

2.PERFORM STEERING ANGLE SENSOR ZERO POINT CALIBRATION
a.

Drive the vehicle straight ahead at 35 km/h (22 mph) or more for at least 5 seconds.


b.

Check that the centered position of the steering wheel is correctly set while driving straight ahead.

HINT:

If the front wheel alignment and steering position are adjusted as a result of an abnormal centered position of the steering wheel, acquire the yaw rate and acceleration sensor zero point again after the adjustments are completed.


OK:

The centered position of the steering wheel is correctly set.



Result:
Proceed to
OK
NG



OK

3.RECONFIRM DTC

NG

ADJUST FRONT WHEEL ALIGNMENT OR STEERING POSITION

3.RECONFIRM DTC
a.

Turn the ignition switch off.



Chassis > ABS/VSC/TRC > Clear DTCs
50002 105
c.

Start the engine.


d.

Drive the vehicle at a speed of 35 km/h (22 mph) or more and turn the steering wheel to the right and left.



Chassis > ABS/VSC/TRC > Trouble Codes
50001 105
HINT:

If DTC C1439 or C1445 is not output again, the DTC may have been stored due to a temporary loss of the steering angle zero point calibration, such as when the power voltage drops.


Result:
Result Proceed to
DTCs C1439 and C1445 are not output A
Yaw rate and acceleration sensor and/or steering angle sensor DTC is output B



A

END

B