Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING VALVE › 2017.01–2021.07
RM25T0E _53 Suspension _062777 TIRE PRESSURE MONITORING _0310949 TIRE PRESSURE WARNING VALVE A

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING VALVE  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:
·

Always use a new grommet and valve core when installing the tire pressure warning valve and transmitter.

·

Check that the washer and nut are not damaged, and replace them if necessary.

·

Make sure not to damage the urethane covered backside of the tire pressure warning valve and transmitter (the surface opposite to the side with the ID code) with anything sharp.

·

If installing a new tire pressure warning valve and transmitter, write down the ID number before installation.

·

Check that there is no oil, water or lubricant around the rim hole, tire pressure warning valve and transmitter, washer and nut. Failing to do so may result in improper installation.

·

Use only a specified valve cap. If an unspecified valve cap is used, it may seize to the tire pressure warning valve and transmitter.



PROCEDURE

Hide 1.INSTALL TIRE PRESSURE WARNING VALVE AND TRANSMITTER

a.

Install a new grommet to the tire pressure warning valve and transmitter.

NOTICE:

Do not install a grommet to a new tire pressure warning valve and transmitter, as a new tire pressure warning valve and transmitter has a grommet already installed.



b.

for Short Body with Tire Size 265/70R16:

Record the 7-digit number transmitter ID printed on the tire pressure warning valve and transmitter at the position shown in the illustration.

C348690C06
0.667,0.833 0.927,0.833 0.927,0.833 1.333,1.667 true 5.979,1.344 6.167,0.667 6.167,0.667 6.417,0.667 true 0.479,0.76 0.792,0.958 0.313,0.198 10 false *b 6.458,0.594 6.771,0.792 0.313,0.198 10 false *a
*a Transmitter ID (7-Digit Number) *b Identification Mark



c.

except Short Body with Tire Size 265/70R16:

Record the 7-digit number transmitter ID printed on the tire pressure warning valve and transmitter at the position shown in the illustration.

C370424C06
1.406,1.802 1.521,0.917 1.521,0.917 1.729,0.917 true 6.333,1.281 6.427,0.625 6.427,0.625 6.635,0.625 true 2.844,1.719 2.5,0.583 2.5,0.583 2.333,0.583 false 0.469,1.115 0.781,1.313 0.313,0.198 10 false *d 2.354,1.135 2.667,1.333 0.313,0.198 10 false *c 1.781,0.833 2.094,1.031 0.313,0.198 10 false *2 6.688,0.542 7,0.74 0.313,0.198 10 false *a 2.177,0.49 2.49,0.688 0.313,0.198 10 false *b
*a Transmitter ID (7-Digit Number) *b Identification Mark
*c Surface A *d Surface B



d.

Insert the tire pressure warning valve and transmitter into the valve installation hole from the inside of the rim so that the printed surface can be seen.

NOTICE:
·

Check that there is no visible deformation, damage, or other abnormalities on the tire pressure warning valve and transmitter.

·

Check that there is no foreign matter on the grommet and around the rim hole.

·

If the tire pressure warning valve and transmitter is installed upside down, it may be damaged or fail to transmit signals when driving at high speeds.

·

Use a tire pressure warning valve and transmitter with a part number that matches that of the vehicle.




e.
C278890C01
1,0.667 0.833,0.417 0.833,0.417 0.667,0.417 true 2.75,0.417 2.583,0.167 2.583,0.167 2.417,0.167 true 1.833,0.75 1.417,0.25 1.417,0.25 1.25,0.25 true 1.833,1.167 1.333,1.583 1.333,1.583 1.167,1.583 true 2.333,1.333 1.833,1.75 1.833,1.75 1.667,1.75 true 0.438,0.333 0.75,0.531 0.313,0.198 10 *1 2.167,0.083 2.479,0.281 0.313,0.198 10 *2 1.083,0.167 1.396,0.365 0.313,0.198 10 *3 0.938,1.5 1.25,1.698 0.313,0.198 10 *4 1.438,1.667 1.75,1.865 0.313,0.198 10 *5
*1 Tire Pressure Warning Valve and Transmitter
*2 Rim
*3 Grommet
*4 Washer
*5 Nut


From the outside of the rim, install the washer to the tire pressure warning valve and transmitter, which has the grommet installed. Afterward, using an 11 mm deep socket wrench, tighten the nut.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

NOTICE:
·

No further tightening is required once the nut is tightened to the specified torque.

·

Check that there is no foreign matter on the washer and nut.




f.
C278915C01
0.917,1 1.333,1 false 2.083,2.958 2.5,2.958 false 1.083,0.5 1.417,0.5 1.417,0.5 1.667,0.75 false 2.333,2.448 2,2.448 2,2.448 1.75,2.698 false 0.833,1.333 1.167,1.333 1.167,1.333 1.417,1.5 true 2.5,3.333 2.333,3.333 2.333,3.333 2,3.5 true 0.688,0.917 1,1.115 0.313,0.198 10 false *1 2.583,2.844 2.896,3.042 0.313,0.198 10 false *1 0.854,0.417 1.167,0.615 0.313,0.198 10 false *a 0.604,1.25 0.917,1.448 0.313,0.198 10 false *b 2.448,2.333 2.76,2.531 0.313,0.198 10 false *a 2.604,3.25 2.917,3.448 0.313,0.198 10 false *b 1.25,1.75 1.583,2 0.333,0.25 10 false *c 2.083,3.75 2.417,4 0.333,0.25 10 false *c
*1 Rim
*a Mount Tool of Mounting Machine
*b Area for Tire Pressure Warning Valve and Transmitter
*c 60°
V100135

Rim Rotation Direction


Set the tire and disc wheel onto the mounting machine.

NOTICE:
·

Make sure the tire pressure warning valve and transmitter is positioned in the area shown in the illustration when set to the mounting machine. Otherwise, the tire pressure warning valve and transmitter may interfere with the tire bead and become damaged.

·

Position the main body of the tire pressure warning valve and transmitter in the area shown in the illustration.




g.

Apply a sufficient coat of soapy water or equivalent to the tire bead and rim.

NOTICE:

Do not apply soapy water or equivalent directly to the tire pressure warning valve and transmitter.



h.

Using a mounting machine, install the tire to the disc wheel.

NOTICE:
·

Make sure that the tire bead and mount tool do not interfere with the tire pressure warning valve and transmitter.

·

Make sure that the tire pressure warning valve and transmitter is not clamped by the bead and rim.




i.

Install a new valve core.


j.

Adjust the tire pressure to the standard tire pressure.


k.

After the tire is inflated, the valve nut may be loose. Using an 11 mm deep socket wrench, retighten the nut to the specified torque.

Torque:
4.0 N*m (41 kgf*cm, 35 in.*lbf)

NOTICE:

No further tightening is required once the nut is tightened to the specified torque.



l.

Check for air leaks with soapy water.

If there is air leakage, push the valve core 2 or 3 times to remove any dirt attached to the valve core. If air continues to leak, replace the grommet, washer and nut.


m.

Install the valve cap.


Hide 2.INSTALL FRONT WHEEL

Hide 4.INSTALL SPARE TIRE